The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, so the water ring vacuum pump is used for exhaust to achieve the of water inlet.ZendehJan,　　The rotation direction of QW (WQ) submersible non blocking sewage pump after connection is counterclockwise from the water inlet. Assuming that the electric pump rotates, it is only necessary to adjust the wiring direction of any two wires in the cable.　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, soMokolo　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.　　Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump tighten the adjusting screw of the bearing box evenly, and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ, When δ= A (. ~ mm　　Its main features are as follows: the whole machine is a dry-type motor pump structure. The motor is protected by mechanical seal, which can effectively prevent high-pressure water and impurities from entering the motor cavity. In addition to the main impeller, it is also equipped with a mixing impeller, which can pump out the slag settled at the bottom after stirring into turbulence. impeller

　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submerged　　First of all, the slurry pump is divided into three categories from the installation method: horizontal slurry pump,ZendehJanDeep well pump, vertical slurry pump, submersible slurry pump horizontal slurry pump: also known as dry installation slurry pump, because it is installed on the ground and the surface of the pump body cannot contact the slurry, it is called dry installation. When this type of pump is installed,　　In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself,ZendehJanSplit vertical pipeline pump, so it is also a reminder that we are using it tooThe cost is reasonable,　　Reasonable.　　In addition to the method, materials shall be selected comprehensively according to the nature of corrosive medium, anti cavitation theory,ZendehJanBooster pipeline pump, corrosion mechanism of water pump and stress characteristics. In order to prolong the service life, which should be a comprehensive optimization design method.　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,

　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,　　Flexibility. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　In recent years, domestic stainless steel pipeline pump products have greatly improved their technical level through introduction, absorption, digestion and innovation, especially the supporting products of some major technical equipment have reached or approached the advanced level of similar products.　　The fruit is also bad; When the axial flow pump is used, its water output is relatively large, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from oneZendehJan,　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.　　Third, the whole industrial and mining system operates stably, and the operation of the pump will not affect the work of the whole industrial and mining system.　　Some impurities will entangle the impeller, so generally, the open impeller will be used, so there is no need to worry about getting stuck in the process of transporting sewage.