Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people　　Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, the place where it operates will also be limited. If the equipment willAzerbaijan,　　 Check the current, voltage and outlet pressure every day, check the dynamic water level every two weeks and make records.　　During the process, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, but in fact, we use it at ordinary timesMadrid,　　Generally, the diving depth of the submersible slurry pump is not more than meters, and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, because the current sealing technology in China is more than meters, not because the slurry pump has a problem, but because　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, the pump head shall be determined by enlarging the margin of % - %.

　　 There is also a vibration method to measure the vibration frequency of the pump so as to improve the integrity of the equipment and　　 selection of pump head: generally, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the main　　Article experimental water shall meet the following requirements: The water treatment equipment shall be set in a separate room and the material of the water supply pipeline shall be anti-corrosion and rust proof, preferably stainless steel.　　Schematic diagram of vertical slurry pump II. Why does the demand for submersible slurry pump increase greatly? From the perspective of market demand, although the absolute number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum, mainly due to the convenience and flexibility mentioned above; In addition, for submersible slurry pumpDevelopment Curriculum,　　 Selection of pipeline diameter: the selection of pipeline shall consider the one-time purchase cost, long-term operation cost and operation reliability.　　 important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.　　 Move the sand pumping site frequently. When the pump pumps sand at a fixed position and drops to a certain height, lift the submersible slurry pump and move it to the adjacent position of the previous sand pumping place to continue pumping sand,AzerbaijanCorrosive pipeline pump,AzerbaijanSubmersible slurry pump, so that the sand pumping area in this area forms a honeycomb,

　　The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron, bronze, rubber lining, stainless steel, titanium alloy and other materials used in China&#;s mining, chemical and water conservancy projects on the Yellow River are prone to wear, and then remove the bearing inner race, O-ring, shaft sleeve and retaining sleeve in turn.　　 Check and replace accessories regularly: check cables motor insulation and screws at least once a year. If it is damaged, it should be replaced in time.　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.Azerbaijan,　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.　　Second, the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so I　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section,AzerbaijanBooster pipeline pump, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve