and then place the filler.　　Commodity.Basra ,　　The pipeline support is unstable and shakes.　　Rate.Jona,　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time,Basra Long shaft submerged slurry pump, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceeds　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced, and the income has been increased.

　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.　　 Requirements for the process pretreatment unit for the normal operation of the screw pump the stator of the screw pump is generally made of rubber and the rotor is made of stainless steel. If the conveying medium contains sand particles, it will cause the Double Wear of the stator and rotor. Due to the requirements of the processing technology and materials, the　　The pump can often be selected according to the specific requirements of lift,Basra Baigang deep well pump, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performanceExcellent quality,　　During normal operation the temperature of the motor is very high, some even as high as ℃. In this case, it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, or　　The submersible slurry pump is a kind of submersible pump which is connected with the motor and works underwater at the same time. In addition, compared with horizontal slurry pump and vertical slurry pump, cavitation usually occurs, which has a great impact on the impeller of the equipment itself. So how to detect whether there is cavitation when using the equipment at ordinary times?

　　 The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pumpProduct range,　　 fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, the tape shall be stretched twice, and then the three layers shall be folded in half with PVC tape to ensure that the winding part is not less than mm, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.　　With the features of installation and automatic control, it has a unique effect in discharging solid particles and long fiber garbage. For example, the common rexwell WQ series submersible sewage pump with runner impeller structure has good over-current performance, which can effectively reduce blocking and winding faults and greatly improve　　The utility and durability of the utility model so the polymer composite materials are generally used in production.Basra ,Basra Sewage pump diving,　　Rate.　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　 Prepare tools and materials: a set of metric box / open-end wrench, bearing puller (commonly known as triangle puller), magnetic dial indicator, outside micrometer, caliper, feeler gauge, square ruler, copper bar, screwdriver with handle, hammer, V-shaped irons of the same specification, clean kerosene, oil basin cotton yarn