It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.The shafts in the middle of the support rods of the hydraulic lifting platform are inconsistent, causing the lifting platform to fail to work normally, the platform is severely damaged, and the table is tilted. Please check carefully that the general scissor aerial work platform has not been strictly tested before leaving the factory, and it has been put into the market. Caused a lot of accidents to take place, for the tilt detection, the detection of this link is not very concerned about for the majority of small enterprises, which is why there are such a large number of lifting equipment to have this problem. Problems with the oil cylinder and the power unit system are often caused by insufficient power and unqualified quality of the oil cylinder, which is also a problem that the enterprise itself needs to pay attention to.Unscrew the screw on the dust-proof hole outside the flange of the elevator, and tighten the inner hexagon. After that, remove the motor shaft key.Scheme customization,The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.System: explosion-proof electronic control system, remote control system, P IC system.If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.
Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.Honest service,Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.The main structure and application of the guide rail elevator: the mechanical part of the guide rail elevator mainly includes three parts: the lifting device, the track device and the belt changing device. The main function is to provide the moving track to make the operation more smooth. The belt changing device is used to switch the track when the elevator is going to pass the door. Lifting device The internal structure of the lifting device is mainly composed of gear mechanism, bracket, worm gear, guide mechanism boom, upper and lower shells etc. Gear mechanism The gear mechanism mainly includes large and small gears, a winding wheel, a middle shaft, and a safety device composed of a stop buckle and a torsion spring.Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles containers, mold manufacturing wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, Turntable, steering, tilting, telescopic), linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting,BayannurChain type cargo elevator, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.Bayannur,In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.
The delivery speed is very fast, give your company a thumbs up
Good seller, thank you. My colleagues like BayannurOil pressure track lifting cargo elevator very much. Come again next time!
I’ve been too busy lately, it’s too late to confirm, BayannurOil pressure track lifting cargo elevator is very good, like the boss.
BayannurOil pressure track lifting cargo elevator It can be said to be top-notch, and the details are perfect.
I’m really sorry.