Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.AIX Provence,AIX ProvenceFixed lifting cargo elevator,The opening system of the manual hydraulic stacking platform truck is divided into pedal type and manual type for selection, which is simple and easy to operate. The models are divided into fixed and mobile forks, and there are many options for ordinary legs and straddle legs. It is very suitable for warehouse, supermarket retail merchandise placement, and extraction.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Surcin,Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines, mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels, post and telecommunications,AIX ProvenceFixed hydraulic lifting cargo elevator, municipal gardens, garages, cleaning companies, public building facade decoration, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, self-propelled, electric start, self-supporting legs, simple operation large working area, especially the ability to cross obstacles for high-altitude operations and the like.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.

Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.The series of standards related to mobile elevators. This series of standards is based on the Ministry of Construction's Jianbiao No. document and [] No. document of the Ministry of Construction's product standards. Standards, this series of standards refers to the American ANSIA- 'boom-type elevating work platform' standard and the American ANSI-A- 'self-propelled aerial work platform' standard, and also refers to relevant European industry standards. The standard was reviewed by relevant Chinese departments on January , . The review opinion is: the series of standards for aerial work platforms are comprehensive in content, strong in support, and sufficient in basis, reflecting the advanced nature and scientific nature of the standards, and the main performance indicators have reached the international advanced level. The standard was published on /.Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Honest management,Test the freight elevator every day to see if the freight elevator can operate normally.Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the load and other factors to choose a lifting platform that suits the work requirements .Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.

The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today,Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.The lifting platform needs to be placed in a ditch position, and the corresponding anti-slip work should be done; remove the gear box of the equipment, remove the shaft holding oil box, take out the lower tile and oil absorber; test the car slowly, it should be smoothed with oilstone; under the motor, and the sleeper is carried on the edge of the ditch inside the rail, and the motor is regularly pulled by a jack to remove the upper tile; the important part of the lifting platform How to deal with equipment damage Check the status of the bearing bush and oil absorber, investigate the cause of damage, replace the bearing bush, install a new oil absorber on the oil box for the shaft, clean the shaft Oil; gear box gear oil in accordance with the regulations; axle box bearing burnout is the most common bearing burnout of the outer row, and in serious cases, the axle box and the wheel set will be fixed together, affecting the operation of the equipment.Fixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, materials on and off the assembly line, parts lifting during large-scale equipment assembly, and fixed three-dimensional parking. So what is the new price of the fixed lift?AIX Provence,The price is guaranteed, the service is guaranteed, and it is a large-scale logistics and storage equipment service company directly operated by the manufacturer. Since the fixed lift is a mechanical device the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods car lifting, fixed three-dimensional parking and other places.In addition to the fixed mode, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.