When the vehicle is replaced with seamless square tube blank, the material is too soft to affect the requirements, so as to ensure the quality of parts and avoid wrinkles.For oil, the oil brush work shall be carried out in accordance with the requirements of the rule system, so as to ensure the oil brush and the oil in the correct position of the brush and avoid wrinkles.Ribnita,Cold formed hollow section steel (American Standard) for cold pressed QB square tube (national standard) structure carbon steel cold-formed circular section and pressure welded QB square tube and seamless QB square tube (European standard) non alloy fine grain cold formed welded hollow structural profile (Japanese standard) angle steel QB square tube for general structure galvanized qb square tube for low pressure fluid transmission, Standard No.: gbt-. Representative materials: qqbqb, etc. it is mainly used to transport water, gas, air, oil and water or steam. It is a special product manufacturing enterprise integrating R & D, and service. It has long been a professional square tube, square tube, seamless square tube, galvanized square tube and galvanized tube. Its purpose is only limited to general low-pressure fluid.A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.Jabbar OS salaj,C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.The strength, plasticity and angle discussed later are the machine function indicators of metal under static load. In practice, many mechanical machines are under repeated load, and the whole opportunity is tired in this environment.Pig iron refers to the product made by smelting iron ore in blast furnace. It is mainly used for steelmaking and square casting. Put the cast pig iron in the melting furnace to obtain cast iron (liquid), and cast the liquid cast iron into a cast square pipe. This kind of cast iron is called cast iron.

The other is designed with deformation angle, which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.The researcher's test before using the strip thinning drawing also confirmed that using the strip thinning drawing can greatly reduce the large value of tangential residual stress of the drawn parts and effectively prevent the occurrence of longitudinal cracking. According to different deformation degree and original sheet thickness, the appropriate thinning coefficient & psi is selected; N (generally .t ~ .t), if & psi; If n is too small, the deformation stress will increase sharply, resulting in the fracture of the bottom of the drawing part.Steel pipe for geological drilling (yb-) is a steel pipe used by geological departments for core drilling. It can be divided into drill pipe, drill collar, core pipe, casing, class II pressure pipe system, boiler and superheater. It is a long-term business square pipe, square pipe, seamless square pipe, galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃, and the working temperature of alloy steel square pipe wall shall exceed ℃.Hot dip galvanized square pipe is widely used, mainly in curtain wall, solar power generation support, construction, machinery and steel structure engineering, especially in curtain wall, machinery and construction. The effect of cold galvanized square tube is far from that of hot galvanized square tube; How to distinguish hot galvanized square pipe from cold galvanized square pipe?

Square tube is an essential material for the construction and Realization of industrialization. It is widely used and has a wide variety. According to different section shapes, square tube is generally divided into sections, plates, ordering and supply of square tube and do a good job in operation and management, it is also divided into heavy rail, light rail, large section steel, medium section steel, small section steel and square tube cold bending Section steel, high-quality section steel, wire rod medium and thick steel plate, sheet steel, electrical silicon steel sheet, strip steel, seamless steel pipe, square pipe, welded steel pipe, metal products etc.build,Ferroalloy is an alloy composed of iron and silicon, manganese,RibnitaPrice of DN100 galvanized pipe, titanium and other elements. Ferroalloy is the raw material for steelmaking. It is used as deoxidizer and alloy element additive for steel in square tube steelmaking.The strip caused by component segregation, that is, when the steel contains harmful impurities such as phosphorus and is pressed and delayed, the impurities elongate along the rolling direction. When the steel is cooled below , making the morphology of ferrite distributed in bands and then pearlite distributed in bands. This band can be eliminated by electroslag remelting and increasing crystallization speed.Steel pipe for geological drilling (yb-) is a steel pipe used by geological departments for core drilling. It can be divided into drill pipe, drill collar, core pipe, casing, sedimentation pipe, etc.Ribnita,Steel for construction and engineering according to the classification of use without phase transformation or partial phase transformation of square tube: A. ordinary carbon structural steel; b. Low alloy structural steel; c. Steel reinforcement.The other is designed with deformation angle which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.Square tube structural steel A. mechanical steel: (a) quenched and tempered structural steel; (b) Surface hardening structural steel: including carburized steel, ammoniated steel and surface quenching steel; (c) Easy to cut structural steel; (d) Steel for cold plastic forming: including steel for cold stamping and steel for cold heading.