The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,　　 The rotor assembly is designed according to the actual situation, and the operation is more stable!Manama,　　The quality of the substitutes produced is not up to the standard, and the price of imported spare parts is expensive; Moreover, in the subsequent sludge treatment unit, the flow passage parts of the centrifugal dehydrator are more sensitive to sand particles. Therefore, sand particles in the conveying medium shall be minimized.　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time,ManamaWear resistant slurry pump, it is necessary to check whether the bottom valve is open and make corresponding adjustment.Fort treller,　　It can improve the mechanical efficiency to a certain extent. Moreover,ManamaVertical slurry pump, the molecular structure of the coating itself has good compactness which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possible　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged　　Yes, summer is the peak sales season. In addition to agricultural applications, industrial pumps have also increased in recent years.

　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.　　 sedimentation tanks, hydropower stations, rivers, power plants, open caissons, mines and fish ponds.　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer.equipment maintenance ,　　The direction of the differential pressure force is opposite, which can offset part of the axial force and prolong the service life of the bearing.　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submerged　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product and the submersible slurry pump is a newly developed product according to the market demand

　　Superior, reasonable structure complete protection s, convenient installation and high cost performance. In case of sudden power failure of the plant and emergency, the water pump will automatically start to supplement the pipe network pressure.Good quality,　　It is also necessary to clean the ventilation duct to avoid blockage.　　In fact, as long as we understand the structure and working principle of the slurry pump, this problem is very easy to solve. We all know that the working principle of the slurry pump is to use centrifugal force to transport slurry, so we need to rotate the impeller of the slurry pump, and the connection between the impeller and the pump shaft is connected through screw threads.　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.Manama,　　In addition to the method, materials shall be selected comprehensively according to the nature of corrosive medium, anti cavitation theory, corrosion mechanism of water pump and stress characteristics. In order to prolong the service life, mechanical seals occupy an increasing share in the slurry pump seal market.　　Limited. According to relevant materials, the diameter of the impeller after cutting shall not be less than % of the diameter of the standard impeller, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut, the flow area in the pump body increases, which makes the flow increase after the impeller is cut.