Alloy pipes can be used for heating (cooling) projects.Key technical characteristics of alloy pipeGambetta ,Reinforcement mesh is manufactured by automatic and intelligent production line under the strict quality control of the factory. Grid size, reinforcement specification and quality are strictly controlled. The longitudinal and transverse bars of the reinforcement mesh form a network structure, so it has good bonding and anchorage with the concrete, and the load is evenly distributed, which obviously shows the seismic crack resistance of the reinforced concrete structure.Whether I-section steel is ordinary or light, because the section size is relatively high and narrow,Gambetta Alloy pipe for power plant, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.Delta del Tigre,Determined by the shape the section modulus, moment of inertia and corresponding strength of I-beam are obviously better than those of ordinary I-beam with the same single weight. When used in metal structures with different requirements, it shows its superior performance in bearing bending moment, pressure load and eccentric load. Compared with ordinary I-beam, it can greatly improve the bearing capacity and save metal by % ~ %.At present, there is still a big gap in the production technology of C-section steel between China and foreign countries.The specification of pass design I-beam is expressed in cm of waist width. For example the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No., cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.

→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure. It has iron zinc alloy layer and compact combination, which shows unique corrosion resistance in marine salt spray atmosphere and industrial atmosphere;What is the stainless steel passivation of alloy pipe?original,Alloy pipe is a kind of seamless steel pipe. Alloy pipe is divided into structural seamless pipe and high-pressure heat-resistant alloy pipe. It is mainly different from the production standard and industry of alloy pipe. Annealing and tempering of alloy pipe changes its mechanical properties. Meet the required processing conditions. Its performance is higher than that of ordinary seamless steel pipe, its utilization value is higher, the chemical composition of alloy pipe contains more Cr, and its performance of high temperature resistance, low temperature resistance and corrosion resistance. Ordinary carbon seamless tubes do not contain alloy components or have few alloy components. Alloy tubes are widely used in petroleum, aerospace, chemical industry, boiler and other industries because the mechanical properties of alloy tubes change and are easy to adjust.After the passivation treatment of alloy pipe, it is clearly proposed that water cleaning shall be carried out immediately after the aqueous solution ~ times of water cleaning, and then chromic acid closed solution shall be carried out. Chromic acid solution must be carried out h after the subsequent water cleaning of metallographic structure and austenitic alloy pipe. Chromic acid aqueous solution (mass ratio) is % ~ %, the solution temperature is ~ ℃, and the solution time is min. Then dry.Under the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.

Frame line crackPotential development, Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding, when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded. Seamless pipe is resistant to corrosion,Gambetta Precision cold drawn seamless pipe manufacturer, alkali, salt and atmospheric environment high temperature,Gambetta Which is easy to use for steel bar software, impact and fatigue, and the effective life is more than years;The high-temperature passivation treatment of alloy pipe is to obtain the passivation treatment film by heating in the heat treatment equipment. Before passivation treatment, the surface layer of parts must be removed to remove waste. At a higher temperature, the passivation treatment film can be obtained according to the transformation temperature and time. The hue of passivation treatment film can refer to the annealing color of alloy pipe, and the main parameters of ambient temperature and time of heat treatment process can be selected.Gambetta ,What is the stainless steel passivation of alloy pipe?Function of I-beam: where is I-beam mainly used?The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.