Precautions for daily maintenance of hydraulic elevator: Check all hydraulic pipelines and joints of the hydraulic elevator. The pipelines must not be damaged, and the joints must not be loose. All joints must be tightened.During use, the elevator should be placed on a solid and flat ground to prevent tipping during operation. Press&quo; Rising; Or&quo; Descending; Press the button to frequently check and maintain the various components of the elevator when lifting the workbench. If the workbench does not move, it should be immediately stopped for inspection. When the working pressure of the electric elevator is found to be too high or the sound is abnormal, it should be immediately shut down for inspection to avoid serious mechanical damage; Regularly check the working status of the shaft pin every month. If any loose shaft pin or screw is found it must be locked tightly to prevent accidents caused by the shaft pin falling off.Nashville,The indicator light is on press the up button, the motor rotates but the lifting table does not rise. Check≥ Phase power supply,NashvillePrice of lifting hydraulic platform,NashvilleMobile hydraulic lifting platform, after the power supply is reversed, the motor reverses, and only needs to correct the power supply.Each department's electric brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than %Suceava ,NashvilleHydraulic lifting platform fixed hydraulic,How to maintain elevators in winter is one reason and the primary reason. Many workers in other industries do not know that hydraulic elevators use different types of hydraulic oil in summer and winter. Often, at low temperatures, the hydraulic oil used in summer can become, or even freeze. After entering low temperatures in winter, which is suitable for working at low temperatures.Good stability: The overflow valve can prevent excessive system pressure during upward movement. Emergency manual valve: In case of power failure, it can cause the elevator car to descend to the nearest floor position and open the door. Manual pump: When the system malfunctions, the manual pump can be operated to pump high-pressure oil to raise the car to the nearest floor position; Tank oil temperature protection: When the oil temperature in the tank exceeds the standard setting value, the oil temperature protection device sends a signal to suspend the use of the elevator. The elevator can only be started when the oil temperature drops.When working at heights exceeding . meters, safety nets or safety belts must be used. Specializing in scissor lift manufacturers, old brand, with price advantages and guaranteed quality!

Once the freight elevator malfunctions, the maintenance unit shall arrive at the site within the specified time (the specific time is not specified in Beijing, but within minutes).The brake operators of each mechanism on the equipment should regularly inspect and adjust the clearance of the brake pads and wheels, ensuring flexibility and reliability.The inconsistent production dimensions of the hydraulic lifting platform support rods are a quality defect of the lifting platform equipment itself. It is recommended that the manufacturer replace them, as the probability of this situation occurring is relatively low.Installation works, tighten the joint and remove the oil filter. After cleaning, clean it with compressed air, and then return it to the oil tank and connect the pipeline.The product has a sturdy structure, a large load-bearing capacity, smooth lifting, and easy installation and maintenanceDo not adjust the solenoid valve on the motor arbitrarily. The solenoid valve is pre adjusted before leaving the factory, and random adjustment can easily cause internal pressure to increase or decrease. In severe cases, it can shorten the service life of the motor.

The principle of shouting loudly when someone is overloaded with moving things is the same, so never overload!market price,When working at heights exceeding . meters, old brand, with price advantages and guaranteed quality!When the motor connection of the elevator is incorrect, when a coil, coil group, or one phase winding group is connected in reverse, it can cause serious three-phase current imbalance and cause the winding to overheat.Talking about the daily maintenance and use of hydraulic lifting platform motors. Overloading is strictly prohibited, as overloading can increase the burden on the motor and in severe cases, cause the motor to burn out.Nashville,Motor does not rotate: The motor is broken, and the manufacturer will handle it. We are a long-term manufacturer of scissor type elevators. Welcome to inquireCheck the hydraulic oil quality and level. When the lifting platform is raised to a high position, the hydraulic oil level should be - millimeters higher than the bottom of the oil tank. When the color of the hydraulic oil darkens, the oil becomes sticky or there are foreign objects such as gravel in the oil, the hydraulic oil should be replaced in a timely manner. The hydraulic system of the lifting platform should be checked for hydraulic and pipeline connections. If the pipeline is damaged, it should be replaced immediately; When there is looseness in the connection part, tighten the pipe joint.The inconsistent production dimensions of the hydraulic lifting platform support rods are a quality defect of the lifting platform equipment itself. It is recommended that the manufacturer replace them, as the probability of this situation occurring is relatively low.