So why is the alloy pipe easy to rust after being pickled and passivated by the software?Ways to obtain surface compressive stress characteristics of alloy tubesSuri, Spiral welded steel pipe (sy- for pile is made of hot-rolled steel strip coil as pipe blank, often warm spiral forming, wharf, bridge, etc.Ways to obtain surface compressive stress characteristics of alloy tubesNalut,What is nitriding of alloy pipeThe delivery length of I-beam is divided into fixed length and double length, and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into -, - and - according to different specification numbers. The length selection range of imported I-beam is generally -.Dry processing technology: after passivation treatment, parts shall be dried with air compression or hot gas or drying treatment or air drying can be selected.

The finished product has smooth surface, low friction coefficient, flatness error + / - mm / m length wear resistance and maximum temperature of ℃Longitudinal welded pipe has the advantages of simple production and processing technology, high production efficiency, low cost and rapid development trend. The compressive strength of spiral welded pipe is generally higher than that of straight welded pipe. Narrow blank can be used to produce welded pipe with large pipe diameter, and blank with the same total width can also be used to produce welded pipe with different pipe diameter. However, compared with the straight seam pipe with the same length, the welding length is increased by ~ , and the production rate is low.The flange of H-beam is of equal thickness,SuriQuotation of high pressure alloy pipe, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.Packaging strategy,I-beam has the dual properties of high hardness and toughness materials. Compared with other engineering wear-resistant materials in China such as various alloy steel plates, cast wear-resistant plates, cast stones, rubber, polyurethane, etc., it has irreplaceable comprehensive excellent properties.Alloy steel pipe is a new type of seamless steel pipe connection pipeline. The selection of pipeline connection pipeline, whether it is fire water system software, water supply equipment, or pipeline, heat and national defense industrial pipeline system software of petrochemical pipeline system, alloy steel pipe stimulates important effects.I-beam has wide flange,SuriDN50 seamless pipe price, thin web, many specifications and flexible use. It can save metal by % ~ % when used in various truss structures. Because the inner and outer sides of the flange are parallel and the edge end is at right angles, it is easy to assemble and combine into various components, which can save about % of the welding and riveting workload, greatly accelerate the construction speed of the project and shorten the construction period.

After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.Variable cost,Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.Generally speaking, the precision of seamless pipe is relatively low, and it is prone to uneven wall thickness low surface luminosity and high customization cost. At the same time, some pits or black spots are easy to appear on the inner and outer surfaces. In addition to these, the seamless pipe manufacturer needs to carry out off-line processing for its detection, and its strength is relatively high, the pressure is high, and its advantages can be reflected in the material of mechanical structure. Seamless pipe can be divided into hot extrusion, different elements can also be used for classification. The inner and outer surfaces of seamless pipes shall be free from chaps, cracks,SuriAlloy pipe gh648, cracks, scabs, delaminations and other defects. If these defects are to be removed, it is necessary to use machining. The removed seamless pipes shall not have negative deviation after the inner diameter is followed, If other minor surface defects with negative deviation cannot be removed, it is not a qualified product. The allowable depth diameter of straight path of seamless pipe is less than or equal to mm, and its depth shall not be greater than . mm.When selecting I-beam in structural design, chemical properties, weldability and structural size. I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams.Suri,Alloy steel pipe is a new type of seamless steel pipe connection pipeline. The selection of pipeline connection pipeline, whether it is fire water system software, water supply equipment, or pipeline, heat and national defense industrial pipeline system software of petrochemical pipeline system, alloy steel pipe stimulates important effects.I-beam also known as universal beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape. Small longitudinal crack