The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bend can also bend R & amp; amp; lt; .T without fracture of pipe wall.Put the pig iron for steelmaking into the steelmaking furnace according to the specified process to obtain steel. The products of steel include ingots, continuous casting billets and various steel castings made of straight square tubes. Generally speaking, steel refers to the steel rolled into various square tubes. Square tube steel belongs to ferrous metal, but steel is not completely equal to ferrous metal.Straseni,The inner and outer walls of the pipe shall retain the original surface without any processing.The surface of fake and inferior square tubes is easy to produce scabs. There are two reasons: the material of fake and inferior square tubes is uneven and there are many impurities. The guide equipment of fake and shoddy material manufacturers is simple and easy to stick to steel. These impurities are easy to scar after biting the roll.Kronov,Improve the positioning and pre bending steps if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.The disadvantage of empty bending is that when the upper side and side are synchronously empty bending,Straseni20 hot dip galvanized square pipe, the forming force is easy to exceed the critical point due to the pressure generated by the upper roll and the lower roll at the same time, resulting in edge instability and concave, and will also affect the stable operation and forming quality of the unit. This is also the different characteristics of qb square tube and round tube empty bending. The concept of square tube: square tube is the pressure processing of ingot, billet or square tube Make materials of all shapes, sizes and properties we need.Generally chemical and electrolytic methods are used

Section shape classification square tubes are classified according to section shape: simple section square tubes & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Surface treatment classification of flower shaped square pipe, open square pipe, corrugated square pipe and special-shaped square pipe square pipe is divided into hot-dip galvanized square pipe, electro galvanized square pipe, oil coated square pipe and pickling square pipe according to surface treatment. Square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machine tools and equipment, machinery industry, chemical industry steel structure, shipbuilding, automobile, steel beam and column and special purpose are classified by wall thickness & mdash& mdash; Super square tube, square tube and thin-walled square tube plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.The square tube is formed by external control or internal control roller.Structural stainless steel square pipe (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square pipe made of stainless steel for corrosion-resistant pipes, structural parts and parts widely used in chemical, petroleum, light textile, food,If the re inspection results are unqualified (including the items whose preliminary inspection results are unqualified and re inspection is not allowed) the supplier can submit them for acceptance one by one; Or re conduct heat treatment (the number of RE heat treatment shall not exceed times), and propose acceptance with a new batch.Plasticity QB square plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.When the vehicle is replaced with seamless square tube blank, so as to ensure the quality of parts and avoid wrinkles.

Square tubes have different functions and different characteristics. Square tubes of various specifications, square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes are welcome to waste merchants, industries, enterprises and power departments to visit and negotiate! Oxidation will also occur on the surface of square tubes after long-term use. What should we do if oxidation occurs? Let me give you a detailed introduction on how to remove square tubes Oxide scale.Where can I find it?,Due to the increase of square tube production, good cold deformation plasticity and weldability; In addition, but it has quite high strength and wear resistance, especially when water quenching; However,StraseniGalvanized square pipe, this steel has great resistance to white spots, temper brittleness and overheating during heat treatment.In this period, the technology of continuous rolling pipe was not mature.Straseni,In the square tube production process of welding before forming, the forming is mainly completed by the sizing frame. The sizing machine is generally a two high mill, including horizontal frame and vertical roll frame. At present, there are mainly two kinds of square pipe pass design: one is the horizontal frame is designed according to the box hole, the frame is an elliptical hole, and the other frames are approximately rectangular holes. The pass section is composed of circular arc. Professional projects include: square pipe, square pipe, seamless square pipe, galvanized square pipe, galvanized pipe and other related businesses. Please welcome merchants who want to have this business. And the arc radius increases frame by frame, The fillet radius of the joint between the side wall and the bottom of all pass patterns is equal to the fillet radius of the finished section. The total elongation coefficient of the square tube is about , which is mainly distributed on the flat roller. The deformation of the vertical roller is very small, and its function is to press down the short side of the square tube. With this design, the calculation is complex and the calculation value is not accurate enough. It is necessary to constantly correct the pass circumference.Viewing color: the color of the cold galvanized square tube is yellowish green, cyan white or slightly colored at a fixed angle with the sun. The color of hot-dip galvanized square pipe is silver white at a fixed angle with the sun.Product description of square tube square tube is a light thin-walled steel tube with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material,StraseniQ235B square tube, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties, weldability, cold and hot workability and corrosion resistance, and good low temperature toughness.

Square tube is a very good steel in economic construction. There are many kinds and principles of cold drawing. You may still have a lot of insufficient understanding of the cold drawing principle of each other's pipe. Next, I'll lead you to learn its cold drawing principle.Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.Koseni,Square tube is the main type of square tube. It is also very popular in the square tube market. There are many people doing this kind of thing, so there are many in the competition. The future market potential is huge. We should grasp this information well. In addition, we must learn about relevant maintenance and repair!Generally speaking, pressurization and thermal insulation.Mongoumba,Special performance steel: A. stainless and acid resistant steel; b. Heat resistant steel: including oxidation resistant steel, heat strength steel and air valve steel; c. Electric heating alloy steel; d. Wear resistant steel; e. Low temperature steel; f. Electrical steel.Cold drawn or cold rolled precision square tube (gb-) is a cold drawn or cold rolled precision square tube with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision square mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. special shaped square pipe is the general name of square pipes with other cross-section shapes except circular pipe. According to the different cross-section shape and size of steel pipe, it can be divided into special-shaped square pipe with equal wall thickness (code D), special-shaped square pipe with unequal wall thickness (code BD) and special-shaped seamless steel pipe with variable diameter (code D) These special-shaped large-diameter qb square tubes are widely used in various structural parts, tools and mechanical parts. Compared with circular tubes special-shaped tubes generally have large moment of inertia and section modulus, and have large bending and torsion resistance, which can greatly reduce the structural weight and save steel. Square tubes are an indispensable part of construction work

Comprehensive classification ordinary steel A. carbon structural steel: (a) Q (b) Q (b); (c) Q( C)； (d) Q( B)； (e) Q.Material classification: square pipe is divided into ordinary carbon steel square pipe and low alloy square pipe.Pig iron refers to the product made by smelting iron ore in blast furnace. It is mainly used for steelmaking and square casting. Put the cast pig iron in the melting furnace to obtain cast iron (liquid), and cast the liquid cast iron into a cast square pipe. This kind of cast iron is called cast iron.wholesalerBrinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.So flat, and the size and thickness are not standardized, it can reflect that this square tube is a poor product& rdquo;Steel used & mdash& mdash; Such as bridge steel, ship steel, boiler steel, pressure vessel steel, agricultural machinery steel,Koseni30 unit price of galvanized square pipe, etc.

Main uses of square tube: square tube is mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products developed.Quality inspection report,Qb square tube, qb square tube, qb square tube, QB square tube, QB square tube and hot-rolled right angle square tube are of good quality and excellent quality. We have become a supplier of many enterprises. Qb square tube and I-beam are two products with different shapes. Under the condition of the same material, but their uses are very different. The shape is different. Qb square tube is a cuboid, and I-beam is in I-shape. The purpose is different. I-beam can be used as span and support. Square pipe is a little worse than span. It is no problem to do support. However, the specific selection of steel depends on the requirements of the project. Square tube practical application square tube for structure (gbt-) is a square tube for general structure and mechanical structure.Shot blasting is commonly used to clean the surface of castings or strengthen the surface of square tubes.Due to the increase of square tube production, there are more and more fake and shoddy square tubes in the market. How to distinguish the fake and shoddy square tubes? Let me teach you some points to distinguish the fake and shoddy square tubes.Koseni,During the pushing process of spot welding and repair welding elbows, there will be thinning, so manufacturers usually use thick spot pipes. If thin raw materials are used, there are about wires thinned. If the technology is not good or the drawn pipe is used, the thickness is significantly lower than the standard.The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high,Koseni150 hot dip galvanized pipe price, the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank, and square pipe with different pipe diameter with blank of the same width. However, compared with straight seam pipe of the same length, the weld length is increased by ~, which will be oriented to the whole country for a long time Individuals and enterprises provide all kinds of square tubes square rectangular tubes, galvanized square tubes seamless square tubes, galvanized tubes, on-site settlement, honest operation, local offices,KoseniHot dip galvanized steel grating, long-term cooperation, most of the smaller square tubes adopt straight seam welding, and most of the large-diameter square tubes adopt spiral welding.Derusting: This is an important process for galvanized square pipes and components before coating, and it is the key to the quality of galvanized square pipes. Thorough derusting can improve the adhesion of antirust paint and prolong the service life of galvanized square pipe.

We all know very well. Therefore, the quality of square tubes will directly affect the development of the construction industry. What if we can make the service life of square tubes longer? Here, we also need to ask the personnel of the square tube manufacturer for instructions, and use ingenious methods to prolong the service life of the square tube, so that the square tube can bring us greater help in life.The pipeline is only subject to chemical pickling which can remove oxide scale, rust and old coating. Sometimes it can be used as the reprocessing after sand blasting. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the surrounding environment. The square tube shall be submitted for acceptance in batches, and the batch rules shall comply with the provisions of corresponding product standards.Sedarenga,Therefore, when the plate is very thick, it should be preheated because it cools quickly. Once # steel was cracked by J welding. If the plate thickness is more than mm, there is a great risk of not preheating.There are many processing technologies for square tubes. I won't introduce the specific processing technology here. We only know about the processing technology of each other's tubes. We may have insufficient understanding of its heating technology. Next, I'll give you a detailed introduction to the heating technology of the lower tubes.We,Reinforcing phases such as reinforcing particles, short fibers and whiskers can be added to the solder to form composites.Hardness hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.B. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.

It should be noted that the position of the disc from the calibration line can be adjusted according to the reinforcement diameter and R and R can be equal or different.The quality of the solid square tube after the square tube formwork removal and curing can be tested according to the requirements and the following ways: use a magnifying glass to observe whether there are non external force cracks on the structural surface of the solid seamless qb square tube. When non external force cracks appear on the surface of qb square pipe, the crack width on the structural surface of ordinary qb square pipe shall not be greater than .mm.Qb square tube, qb square tube, qb square tube, QB square tube, QB square tube and hot-rolled right angle square tube are of good quality and excellent quality. We have become a supplier of many enterprises. Qb square tube and I-beam are two products with different shapes. Under the condition of the same material, the bearing capacity of steel is the same, but their uses are very different. The shape is different. Qb square tube is a cuboid, and I-beam is in I-shape. The purpose is different. I-beam can be used as span and support. Square pipe is a little worse than span. It is no problem to do support. However, the specific selection of steel depends on the requirements of the project. Square tube practical application square tube for structure (gbt-) is a square tube for general structure and mechanical structure.Convenient and efficient,The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.Square tube, modified square tube,SedarengaGalvanized square steel pipe, square tube, QB square tube and hot-rolled square tube are qualified in quality inspection. The manufacturer adopts advanced equipment to ensure the quality of each product. Magnetic flux leakage testing for surface defects of square tubes is very similar to magnetic particle testing for square tubes, and its scope of application, sensitivity and reliability are stronger than magnetic particle testing. Indirect square forming process the traditional forming process of cold-formed square pipe is to gradually roll the hot-rolled steel coil multi stand forming unit into round pipe at room temperature, and then the shaping unit will roll the round pipe into square pipe, which is called indirect square forming process. The traditional roll forming process uses the method of fixed bending point position and variable bending radian to complete the corner forming of pipe blank, which is suitable for rolling small and medium-sized products. Rolling with this process & ldquo; Superb & rdquo; Square tube will show its inherent defects. Because the roll work in the bending process of this process is always concentrated at the point, excessive stress concentration often shows microcracks in the bending process of profiles, due to the different forming bending radians of products with different wall thickness, the universality of rolls is limited. The large-size cold-formed square tube used in the process adopts the advanced & ldquo; Direct Square & rdquo; The production process is to directly roll the hot-rolled steel coil into a square and rectangular shape at room temperature.Improve the positioning and pre bending steps, if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.

With the progress of the times and the development of science and technology, the application fields of square tubes are widely divided. The main fields are the construction industry. Affected by the environment and weather, square tubes will also rust for a long time. How to improve the rust resistance of square tubes and what are its rust resistance? Let me give you a detailed introduction below.system,There are many processing technologies for square tubes. I won't introduce the specific processing technology here. We only know about the processing technology of each other's tubes. We may have insufficient understanding of its heating technology. Next, I'll give you a detailed introduction to the heating technology of the lower tubes.HDPE plastic square pipe made according to the properties of square pipe has the advantages of light texture high strength, good resistance, low water resistance, low cost and corrosion resistance. Its service performance and economic benefits far exceed reinforced concrete pipe and general specification iron pipe. It is an updated product of engineering pipe.Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).Sedarenga,Functional index analysis of qb square tube - angular plasticity refers to the power of plastic deformation (permanent deformation) without destruction of qb square tube data under load.After chemical pickling, the square tube can be well protected by electrolysis. These are simple ways to prolong the service life of the square tube, We only need to treat according to these, so that the square tube can bring us great help in the use process. The cold galvanized square tube is the principle of cold galvanizing on the square tube used to make the square tube have corrosion performance. Different from hot-dip galvanizing, cold galvanizing coating is mainly carried out according to the electrochemical principle. Therefore, it is necessary to ensure the sufficient of zinc powder and steel,Sedarenga5025 galvanized square pipe, resulting in electrode potential difference, so the steel surface treatment requirements are very high.Viewing color: the color of the cold galvanized square tube is yellowish green

With the progress of the times and the faster and faster economic development, the places where large-diameter seamless square tubes are used are becoming more and more popularPrinciple of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.Adine so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation,Chemical polishing: less investment in processing equipment, high speed, high efficiency and good durability. Its defects are poor brightness, gas overflow, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Ghent,The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.Due to the increase of square tube production, there are more and more fake and shoddy square tubes in the market. How to distinguish the fake and shoddy square tubes? Let me teach you some points to distinguish the fake and shoddy square tubes.Tool derusting mainly uses tools such as steel wire brush to polish the surface of square pipe, which can remove loose or oxidized scale, rust, welding slag, etc. The derusting of manual tools can reach grade SA and that of power tools can reach grade SA. If the square pipe surface is firmly attached with iron oxide scale, the derusting effect of tools is not ideal and can not reach the anchor depth required by construction.

Compared with other welding, square pipe welding has many advantages,AdineHow much is galvanized 20 square tube, mainly because of the exothermic reaction, the material only needs to be heated below the melting pointWhen processing the square tube, some processes need to heat the seamless square tube. The heating operation in the processing of the seamless square tube plays a very key role in the quality of the finished seamless square tube.For transportation: water supply, drainage, sewage treatment engineering, mud transportation, marine water transportation.Safety production,Classification of square pipe material square pipe is divided into ordinary carbon steel square pipe and low alloy square pipe according to material. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn, Q, St-, etc.The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high, the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank,AdineWall thickness of galvanized square pipe, and square pipe with different pipe diameter with blank of the same width. However, compared with straight seam pipe of the same length, the weld length is increased by ~, which will be oriented to the whole country for a long time Individuals and enterprises provide all kinds of square tubes square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes, on-site settlement, honest operation, local offices, long-term cooperation, and low production speed. Therefore, and most of the large-diameter square tubes adopt spiral welding.The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bend can also bend R & amp; amp; lt; .T without fracture of pipe wall.

Improve the positioning and pre bending steps if necessary, resulting in uneven walking feeding.resources to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap,Welding is a synthetic gradient material, which can be used as solder to weld special-shaped materials in order to overcome the mismatch of chemical, mechanical and physical properties between base metals.After the square pipe is produced, the surface treatment is generally carried out, that is, the scale, rust, dirt and attachments on the surface of the square pipe are removed. Those that cannot be treated by physical treatment should be treated by chemical treatment.Precision inner diameter square tubes for hydraulic and pneumatic cylinders (gb-) are cold drawn or cold-rolled precision square tubes with precision inner diameter for hydraulic and pneumatic cylinders.Adine,B. low alloy structural steel C. ordinary structural steel and high-quality steel for specific purposes (including high-quality steel)Square tube structural steel A. mechanical steel: (a) quenched and tempered structural steel; (b) Surface hardening structural steel: including carburized steel, ammoniated steel and surface quenching steel; (c) Easy to cut structural steel; (d) Steel for cold plastic forming: including steel for cold stamping and steel for cold heading.In the square tube production process of welding before forming, the forming is mainly completed by the sizing frame. The sizing machine is generally a two high mill, including horizontal frame and vertical roll frame. At present, there are mainly two kinds of square pipe pass design: one is the horizontal frame is designed according to the box hole, and the other frames are approximately rectangular holes. The pass section is composed of circular arc. Professional projects include: square pipe, square pipe, seamless square pipe, galvanized square pipe, galvanized pipe and other related businesses. Please welcome merchants who want to have this business. And the arc radius increases frame by frame, The fillet radius of the joint between the side wall and the bottom of all pass patterns is equal to the fillet radius of the finished section. The total elongation coefficient of the square tube is about ,AdinePrice of 80% galvanized square pipe, which is mainly distributed on the flat roller. The deformation of the vertical roller is very small, and its function is to press down the short side of the square tube. With this design, the calculation is complex and the calculation value is not accurate enough. It is necessary to constantly correct the pass circumference.

Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.Empty bending empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.Conrat,The qb square tube rolled from the strip steel through process treatment is generally to unpack, flatten, curl and weld the strip steel to form a round tube, then roll the round tube into a square tube, and then cut it to the required length. Nowadays, the forming of qb square tube has solid bending and empty bending. The bending degree of qb square tube shall not be greater than mm per meter, and the total bending degree shall not be greater than the actual bending of the total length. As the name suggests, the bending is compacted, and the internal and external rollers and the internal and external walls of the tube blank are compacted in both directions during the actual bending., cold drawn tubes, tubes, etc. Hot rolled seamless tubes are produced on the automatic precision tube precision tube rolling mill. The solid tube blank is cut into the required length by removing surface defects, centering on the end face of the perforated end of the tube blank, and then sent to the heating furnace for heating. It is perforated on the piercing machine. At the same time, it rotates and advances continuously under the action of roll and plug,ConratGalvanized square pipe, A cavity is gradually formed inside the pipe blank, which is called the rough pipe, and then sent to the automatic pipe mill for continuous rolling. After the wall thickness is adjusted by the whole machine, and the diameter is determined by the sizing machine to meet the specification requirements. The continuous pipe mill is more advanced in producing hot-rolled seamless steel pipe. If you want to obtain seamless pipe with smaller size and better quality Cold rolling and cold drawing must be adopted, or the combination of cold rolling and cold drawing is usually carried out on the roll mill. The seamless pipe is rolled in the annular pass composed of variable section circular hole groove and fixed conical plug. Cold drawing is usually carried out on the single chain or double chain cold drawing machine, that is, the heated pipe blank is placed in a closed cylinder, and the perforated rod and rod move This method can produce steel pipe with small diameter. In the building materials industry,Conrat4-inch galvanized square pipe, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. We need to understand the various characteristics of steel pipes. However the development of various pipes is different. Because of their different characteristics, in the building materials industry, the development of various pipes is different. Because of their different characteristics, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. The various characteristics of steel pipe need to be understood by everyone. However, due to the of steel pipe and other raw materials, the storage of steel pipe needs specific conditions.Amol,Compared with other welding, square pipe welding has many advantages, mainly because of the exothermic reaction, the material only needs to be heated below the melting pointHundreds of degrees Celsius, which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, considering the influence of dimensional accuracy and metal work hardening, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy,ConratGalvanized square tube customized, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.

Fake and shoddy square tubes are easy to scratch, because the equipment of fake and shoddy material manufacturers is simple and easy to produce burrs and scratch the surface of square tubes. Deep scratches reduce the strength of square tubes.Tensile strength: - yield strength: & Ge; elongation: & Ge; mechanical properties of seamless pipe: tensile strength: - yield strength: ≥ elongation: & Ge; mechanical properties of seamless pipe: tensile strength: - yield strength: ≥ elongation: & Ge; mechanical properties of seamless pipe: tensile strength: - yield strength: ≥ elongation: & Ge; mechanical properties of seamless pipe: tensile strength: - yield strength: ≥ elongation: & Ge; square tube belongs to low alloy series. It is one of the materials of seamless steel pipe. In low alloy materials, this material is ordinary. Square tube used to be called QB square tube.Functional index analysis of qb square tube - the load on the machine parts due to the great progress of strength is called the frontal collapse load. The power of destruction of qb square tube under the frontal collapse load is called the frontal collapse toughness.total cost,Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. Seamless pipe can be divided into hot rolled pipe and cold rolled pipe according to different productionThe local heat release in the welding process of square tube can reduce the heat affected zone, avoid the micro of thermal sensitive materials, and maintain the properties of materials.Square pipe for diamond core drilling (gb-) is a square pipe for drill pipe, core rod and casing for diamond core drilling.

If the re inspection results are unqualified (including the items whose preliminary inspection results are unqualified and re inspection is not allowed), the supplier can submit them for acceptance one by one; Or re conduct heat treatment (the number of RE heat treatment shall not exceed times), and propose acceptance with a new batch.Sincere serviceStage ( & mdash; )The welded joints of square pipes are subject to on-line continuous ultrasonic automatic flaw detector to ensure the NDT coverage of spiral welds. If there are defects, it will automatically alarm and spray marks. The production will adjust the process parameters at any time to eliminate the defects in time.High quality steel (P & le; .%, S & le; .%)Conrat,For transportation: water supply, drainage, sewage treatment engineering, mud transportation, marine water transportation.The surface of fake and inferior square tubes is easy to produce scabs. There are two reasons: the material of fake and inferior square tubes is uneven and there are many impurities. The guide equipment of fake and shoddy material manufacturers is simple and easy to stick to steel. These impurities are easy to scar after biting the roll.Square pipe welding is suitable for surface treatment of materials. Square pipe welding can be used for ceramic ceramic, metal ceramic and metal metal welding.

Square tube is an essential material for the construction and Realization of industrialization. It is widely used and has a wide variety. According to different section shapes, square tube is generally divided into sections, plates, pipes and metal products. In order to facilitate the production, ordering and supply of square tube and do a good job in operation and management, it is also divided into heavy rail, light rail, large section steel, medium section steel, small section steel and square tube cold bending Section steel, high-quality section steel, wire rod, medium and thick steel plate, sheet steel, electrical silicon steel sheet, strip steel, seamless steel pipe, welded steel pipe, metal products, etc.When storing QB square pipe, we need to select a suitable place. We need to think about many external factors, such as the corrosivity of steel pipe, etc. Therefore, the place must be clean, dry and ventilated, where harmful gases appear, QB square pipe can not appear, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid, alkali salt, etc. in the warehouse, it is easy to react with the steel pipe and corrode the steel pipe, so try to cut it and don't let it. In addition, if we can think about those higher metal products, we can put them into the warehouse for very good retention. According to geographical conditions, there is a sealed warehouse, but the ventilation setting is excellent. The difference between QB square tube and seamless steel tube QB square tube is a kind of high-precision steel tube material after cold drawing or hot rolling treatment. QB square tube is mainly used to produce products of pneumatic or hydraulic components, which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of QB square tube, no deformation under high pressure, high precision, high finish, cold bending, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, manganese Mn, sulfur s, phosphorus P and chromium CR.DubasariThe general delivery length of square pipe is mm-mm, mostly mm and mm. The square tube is allowed to deliver short and non fixed length products not less than mm, or in the form of interface tube,DubasariGalvanized thickness of galvanized square pipe, but the Demander shall cut off the interface tube when using it. The allowable deviation of the wall thickness of square pipe shall not exceed plus or minus % of the nominal wall thickness when the wall thickness is not greater than mm, plus or minus % of the wall thickness when the wall thickness is greater than mm, except for the wall thickness of corners and weld areas. The weight of short gauge and non fixed gauge products shall not exceed % of the total delivery. For square tubes with a theoretical weight greater than kgm, it shall not exceed % of the total delivery. We have many different ways in square tubes. Different ways make square tubes have different characteristics. According to these characteristics, we can correctly select the appropriate application field, In this way, we will mainly explain the characteristics of pipe cooling technology below. What are the main characteristics of square tubes? Square tube parts have accurate dimensions and smooth surfaces: the dimensional accuracy of cold parts developed at present can reach grade ~ . If ideal ones are adopted, their accuracy is second only to that of fine polished surfaces. Therefore, cold parts generally do not need to be reprocessed, and a small amount only need finishing (grinding).Section shape classification square tubes are classified according to section shape: simple section square tubes & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Surface treatment classification of flower shaped square pipe, open square pipe, corrugated square pipe and special-shaped square pipe square pipe is divided into hot-dip galvanized square pipe, oil coated square pipe and pickling square pipe according to surface treatment. Square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machine tools and equipment, machinery industry,DubasariCold galvanized square pipe factory, chemical industry, steel structure, shipbuilding, steel beam and column and special purpose are classified by wall thickness & mdash& mdash; Super square tube, square tube and thin-walled square tube plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.Portachuelo,B. converter steel: (a) acid converter steel; (b) Basic converter steel. Or (a) bottom blown converter steel; (b) Side blown converter steel; (c) Top blown converter steel.Product description of square tube square tube is a light thin-walled steel tube with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties, weldability cold and hot workability and corrosion resistance, and good low temperature toughness.The square tube is divided into a. boiling steel according to the degree of deoxidation and pouring; b. Semi killed steel; c. Killed steel; d. Special killed steel. The deformation of qb square tube is mainly caused by the shrinkage force of the weld greater than the strength of the base metal.

Section shape classification square tubes are classified according to section shape: simple section square tubes & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Surface treatment classification of flower shaped square pipe, open square pipe, oil coated square pipe and pickling square pipe according to surface treatment. Square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration electro galvanized square pipe, machine tools and equipment, machinery industry, chemical industry, steel structure, shipbuilding, automobile, steel beam and column and special purpose are classified by wall thickness & mdash& mdash; Super square tube, square tube and thin-walled square tube plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.Upper yield point (& sigma; Su): the large stress before the yield of the sample occurs and the stress decreases for the first time; Lower yield point (& sigma; SL): the small stress in the yield stage when the initial instantaneous effect is not considered.Superior square tubular steel (both P and s ≤ .%)Quality assurance,Improve the positioning and pre bending steps, if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.For gas transmission: gas, steam and liquefied petroleum gas.B. converter steel: (a) acid converter steel; (b) Basic converter steel. Or (a) bottom blown converter steel; (b) Side blown converter steel; (c) Top blown converter steel.

If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.consumption,Classification of square pipe material square pipe is divided into ordinary carbon steel square pipe and low alloy square pipe according to material. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn, Q, St-, etc.Preheating must be carried out before heat treatment of qb square tube, so as to better ensure that there will be no many problems in the whole heat treatment process of qb square tube, and the quality of qb square tube will also be well guaranteed.The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.Dubasari,According to metallographic classification, the annealed state of square tube: A. hypoeutectoid steel (ferrite + pearlite); b. Eutectoid steel (pearlite); c. Steel precipitation through a common square tube (pearlite + cementite); d. Ledeburite steel (pearlite + cementite).Reinforcing phases such as reinforcing particles, short fibers and whiskers can be added to the solder to form composites.Engaged in square tube, seamless square tube, galvanized square tube,DubasariHow much is the price of galvanized steel pipe per meter, galvanized tube, old brand price advantage and quality guarantee! However, the Demander shall cut off the interface pipe when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square pipe with theoretical weight greater than kgm, it shall not exceed % of the total delivery. The bending degree of qb square pipe shall not be greater than mm per meter, and the total bending degree shall not be greater than .% of the total length. Galvanized qb square pipe for low-pressure fluid transmission, with standard number of gbt-. Representative materials: QA, qbqb etc. It is mainly used for conveying water, gas, air, oil and heating hot water or steam, and its purpose is limited to general low pressure fluid.

In the square tube production process of welding before forming, the forming is mainly completed by the sizing frame. The sizing machine is generally a two high mill, including horizontal frame and vertical roll frame. At present, there are mainly two kinds of square pipe pass design: one is the horizontal frame is designed according to the box hole, the frame is an elliptical hole, and the other frames are approximately rectangular holes. The pass section is composed of circular arc. Professional projects include: square pipe, square pipe seamless square pipe, galvanized pipe and other related businesses. Please welcome merchants who want to have this business. And the arc radius increases frame by frame galvanized square pipe, The fillet radius of the joint between the side wall and the bottom of all pass patterns is equal to the fillet radius of the finished section. The total elongation coefficient of the square tube is about , which is mainly distributed on the flat roller. The deformation of the vertical roller is very small, and its function is to press down the short side of the square tube. With this design, the calculation is complex and the calculation value is not accurate enough. It is necessary to constantly correct the pass circumference.Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension,AoheiGalvanized rectangular pipe, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, it is not allowed to stack with acid, alkali, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, rail, steel plate, large-diameter steel pipe, forging, etc. can be stacked in the open air; Small and medium-sized section steel, wire rod, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets, or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, that is, the warehouse with roof, enclosure, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air i.e. the mouth shall face down, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, loading and unloading and shall not be damaged, The storage period of materials can be extended, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel, alloy steel sheet, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, it can reflect that the square tube is good. On the contrary, if the surface is not goodAohei,Functional index analysis of square tube - commonly used are square tube Brinell angle (HB), Rockwell angle (hrahrbhrc) and Vickers angle (HV) Equal angle is a gauge needle to weigh the soft and hard level of metal data. In the current life, the angle method is rarely used to determine the angle. It uses the indenter with a certain number and shape to determine the angle value of the metal data surface being tested under a certain load according to the level.Welding is a synthetic gradient material, which can be used as solder to weld special-shaped materials in order to overcome the mismatch of chemical, mechanical and physical properties between base metals.Tanta,Impact toughness the load acting on the machine part at a great speed by QB is called impact load, and the ability of metal under impact load is called impact toughness.Stainless steel square tube for fluid transportation (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square tube made of stainless steel for fluid transportation.Fake and shoddy square tubes are easy to scratch, because the equipment of fake and shoddy material manufacturers is simple and easy to produce burrs and scratch the surface of square tubes. Deep scratches reduce the strength of square tubes.

Put the pig iron for steelmaking into the steelmaking furnace according to the specified process to obtain steel. The products of steel include ingots, continuous casting billets and various steel castings made of straight square tubes. Generally speaking, steel refers to the steel rolled into various square tubes. Square tube steel belongs to ferrous metal, but steel is not completely equal to ferrous metal.Shot blasting and sand blasting are widely used in repair and shipbuilding industry. However, whether shot blasting or sand blasting, compressed air is used. Professional square pipe, square rectangular pipe, seamless square pipe,AoheiGalvanized strip pipe, galvanized square pipe galvanized pipe has high pressure resistance grade, good waterproof performance, fire and high temperature resistance, strong overload capacity, corrosion resistance, it is not shot blasting, so it is necessary to use high-speed rotating impeller. In the repair and shipbuilding industry, shot blasting (small steel shot) is mostly used in square pipe pretreatment (rust removal before coating); Sand blasting (mineral sand is used in repair and shipbuilding) is mostly used in formed ships or sections to remove the old paint and rust on the square tube and repaint it. In the repair and shipbuilding industry, the main function of shot blasting and sand blasting is to increase the adhesion of square tube coating paint.Square tube structural steel A. mechanical steel: (a) quenched and tempered structural steel; (b) Surface hardening structural steel: including carburized steel, ammoniated steel and surface quenching steel; (c) Easy to cut structural steel; (d) Steel for cold plastic forming: including steel for cold stamping and steel for cold heading.Recommendation and consultation,The technology of floating mandrel and square tube is gradually mature.Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency),AoheiHow to galvanize square tube, gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Straight seam welded square pipe, spiral weldingPrinciple of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.

Derusting grade for the construction process of epoxy, ethylene, phenolic and other coatings commonly used for square pipes, the surface of square pipes is generally required to reach near white grade (SA). Practice has proved that almost all oxide scale rust and other dirt can be removed by using this derusting grade, and the depth of anchor grain can reach ~ & mu; m which fully meets the requirements of adhesion between layer and square pipe The shot derusting process can meet the technical conditions of near white level (SA) with low operation cost and stable and reliable quality.High value,Pig iron refers to the product made by smelting iron ore in blast furnace. It is mainly used for steelmaking and square casting. Put the cast pig iron in the melting furnace to obtain cast iron (liquid), and cast the liquid cast iron into a cast square pipe. This kind of cast iron is called cast iron.How about the tensile strength of square pipe: square pipe has good tensile strength, tensile strength and sufficient toughness, which makes square pipe stand out in the field of steel pipe. The square tube has great advantages in high temperature, high pressure and even high strength environment. What are its characteristics? We analyze it one by one: tensile strength (& sigma; b) the strong force (FB) borne by the sample during tensile breaking, and the stress (& sigma;) obtained from the original cross-sectional area (so) of the sample is called tensile strength (& sigma; b), and the unit is nmm (MPA).Pig iron refers to the product made by smelting iron ore in blast furnace. It is mainly used for steelmaking and square casting. Put the cast pig iron in the melting furnace to obtain cast iron (liquid), and cast the liquid cast iron into a cast square pipe. This kind of cast iron is called cast iron.Aohei,Functional index analysis of qb square tube - angular plasticity refers to the power of plastic deformation (permanent deformation) without destruction of qb square tube data under load.C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.With the progress of the times and the development of science and technology, the application fields of square tubes are widely divided. The main fields are the construction industry. Affected by the environment and weather, square tubes will also rust for a long time. How to improve the rust resistance of square tubes and what are its rust resistance? Let me give you a detailed introduction below.

Product description of square tube square tube is a light thin-walled steel tube with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties,SorokaSpecification of galvanized square pipe, weldability, cold and hot workability and corrosion resistance, and good low temperature toughness.Alloy steel: A. low alloy steel (total alloy element content & le; %); b. Medium alloy steel (total alloy element content > ~ %); c. High alloy steel (total alloy element content > %).Soroka, and cast the liquid cast iron into a cast square pipe. This kind of cast iron is called cast iron.Hinche,The reason why the surface of fake and shoddy materials is easy to crack is that its blank is adobe with many air holes. During the cooling process, and there are cracks after rolling.Generally, chemical and electrolytic pickling are used for pickling treatment. Only chemical pickling is used for pipelines, which can remove oxide scale, rust and old coatings. Professional square tubes, rectangular tubes, seamless square tubes galvanized square tubes and galvanized tubes are safe, environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted. Sometimes they can be used as reprocessing after sand blasting and rust removal. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the environment.Oil drilling pipe (yb-) is a square pipe used for internal or external thickening at both ends of oil drilling. Steel pipes are divided into turning wire and non turning wire. Turning wire pipe is connected with joint, and non turning wire pipe is connected with tool joint by butt welding.

Viewing color: the color of the cold galvanized square tube is yellowish green, cyan white or slightly colored at a fixed angle with the sun. The color of hot-dip galvanized square pipe is silver white at a fixed angle with the sun.Square tube saves raw materials: the material rate of cold parts can usually reach more than %. For example, while the material rate when cold is used is increased to %; For another example, after the universal joint bearing sleeve is changed to cold, the material rate is increased from % in the past to%. It can be seen that the use of cold production of mechanical parts can save a lot of steel and non-ferrous metal materials.Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.Welcome to inquire,B. low alloy structural steel C. ordinary structural steel and high-quality steel for specific purposes (including high-quality steel)B. converter steel: (a) acid converter steel; (b) Basic converter steel. Or (a) bottom blown converter steel; (b) Side blown converter steel; (c) Top blown converter steel.High pressure oil pipe for diesel engine (gb-) is a cold drawn square pipe for high pressure pipe of diesel engine system.

Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).safety requirements ,Special performance steel: A. stainless and acid resistant steel; b. Heat resistant steel: including oxidation resistant steel, heat strength steel and air valve steel; c. Electric heating alloy steel; d. Wear resistant steel; e. Low temperature steel; f. Electrical steel.Performance index analysis of square tube - impact toughness the load acting on the part at a great speed is called impact load, and the ability of metal under impact load is called impact toughness.Derusting: This is an important process for galvanized square pipes and components before coating, and it is the key to the quality of galvanized square pipes. Thorough derusting can improve the adhesion of antirust paint and prolong the service life of galvanized square pipe.Soroka,Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid alkali, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, rail, steel plate,Soroka76 galvanized square pipe, large-diameter steel pipe, forging, etc. can be stacked in the open air; Small and medium-sized section steel, wire rod reinforcement, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips,SorokaGalvanized strip pipe, silicon steel sheets, or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, and generally adopts ordinary closed warehouse that is, the warehouse with roof, enclosure, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation loading and unloading and shall not be damaged, The storage period of materials can be extended, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned but for high-quality steel, alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, it can reflect that the square tube is good. On the contrary, if the surface is not goodAccording to metallographic classification, the annealed state of square tube: A. hypoeutectoid steel (ferrite + pearlite); b. Eutectoid steel (pearlite); c. Steel precipitation through a common square tube (pearlite + cementite); d. Ledeburite steel (pearlite + cementite).Comprehensive classification ordinary steel A. carbon structural steel: (a) Q (b) Q (b); (c) Q( C)； (d) Q( B)； (e) Q.

Mechanical engineering, power plants, agricultural and chemical machinery, glass curtain walls, automobile chassis, airports, boiler construction, highway railings, housing construction, pressure vessels, oil storage tanks, power station equipment, heavy transportation machinery and other welded structural parts with high load, etc. Process classification: according to the production process, square tubes are divided into hot-rolled seamless square tubes, cold drawn seamless square tubes, seamless square tubes and qb square tubes.The local heat release in the welding process of square tube can reduce the heat affected zone, avoid the micro of thermal sensitive materials, and maintain the properties of materials.Kahur,In different environments, the use efficiency of square tubes is different. According to the quality of square tubes, we will conduct progressive research on them, hoping to develop better square tubes. No matter what environment, we will make square tubes suitable for use. Then, let's introduce it to you.Derusting grade for the construction process of epoxy, ethylene, phenolic and other coatings commonly used for square pipes, the surface of square pipes is generally required to reach near white grade (SA). Practice has proved that almost all oxide scale, rust and other dirt can be removed by using this derusting grade, and the depth of anchor grain can reach ~ & mu; m, which fully meets the requirements of adhesion between layer and square pipe The shot derusting process can meet the technical conditions of near white level (SA) with low operation cost and stable and reliable quality.Majorna,Impact toughness the load acting on the machine part at a great speed by QB is called impact load, and the ability of metal under impact load is called impact toughness.Derusting: This is an important process for galvanized square pipes and components before coating, and it is the key to the quality of galvanized square pipes. Thorough derusting can improve the adhesion of antirust paint and prolong the service life of galvanized square pipe.In recent years, large-diameter seamless square tube plays a good role in economic development. Because there are many types of large-diameter seamless square tubes, the continuous casting process of large-diameter seamless square tubes is also different. What are the specific steps of the continuous casting process of large-diameter seamless square tube? As the name suggests, square tube is a kind of square tube type. Many materials can form square tube body. Its medium is used for what purpose and where it is used. Most square tubes are steel tubes, which are unpacked, leveled, crimped and welded to form round tubes, Then the round pipe is rolled into a square pipe, and then cut into the required length. Generally, square tubes per package are mostly in large specifications in terms of spot, and . - ~~ - square tubes are divided into structural square tubes decorative square tubes,Kahur100 galvanized square pipe, building square tubes, mechanical square tubes, etc. according to their uses.

Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but the production efficiency is very high and there are many specifications and varieties, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.After, the workpiece forms an oxide film with a fixed thickness and presents various colors. Chemical oxidation method is to form various film colors in a specific solution at temperature and time; Because of the law & rdquo; More, but to maintain the color of the product, the reference electrode must be used. Electrochemical method is to form the color of chloride film with fixed thickness in specific electrolyte at temperature, voltage and time. This process is mature and widely used. Ion implantation method is to vaporize ions in vacuum and deposit them on the surface of qb square tube, such as watch case on the market. The golden color of watch strap adopts this process technology, which is suitable for mass production. The process of gas phase cracking is more complex and less used in industry. Square tube has long been widely used in mechanical industry. When the square pipe is cut automatically, when the square pipe is hoisted to the gas cutting platform, the distance difference between the two ends of one side of the pipe and the guide rail shall be adjusted within mm. During semi-automatic cutting, the guide rail shall be placed on the plane of the cut pipe, and then the cutting machine shall be placed on the guide rail gently.The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.Discount,Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours improve material rate and improve product quality. Seamless pipe can be divided into hot rolled pipe and cold rolled pipe according to different productionWhen sand blasting or manual mechanical derusting is used, the metal on the surface of the galvanized square pipe is directly exposed in the air. If a primer is not applied in time, the surface of the galvanized square pipe is easy to rust again, affecting the adhesion of the paint film. I am engaged in all kinds of square tubes square rectangular tubes, seamless square tubes,KahurGalvanized square pipe quick connector, galvanized square tubes, galvanized tubes and other materials all year round. I operate in good faith. Welcome to call! As the paint is a time-effective material, the overstock of inventory is easy to expire. Therefore, the main indexes of the paint must be rechecked before use, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally,KahurHow much is a 60 galvanized pipe, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse it is not allowed to stack with acid, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, rail, steel plate, large-diameter steel pipe, forging, wire rod, reinforcement, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets, or thin-walled steel pipes all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, and generally adopts ordinary closed warehouse, that is the warehouse with roof, enclosure, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, loading and unloading and shall not be damaged, The storage period of materials can be extended, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel, alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, it can reflect that the square tube is good. On the contrary, if the surface is not goodQuotation sheet,With the improvement of production quality, the quality of square tubes is getting better and better. The quality of square tubes will affect our lives. Because the functions of square tubes are different, their characteristics and uses are different. I will introduce the characteristics and uses of square tubes in detail.Electrochemical polishing: long specular gloss, less pollution and good durability. Suitable for mass production, it is mainly applied to high-grade products, imported products and public service products. Its processing technology is stable and the operation is simple.Main uses of square tube: square tube is mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products developed.Kahur,Special performance steel: A. stainless and acid resistant steel; b. Heat resistant steel: including oxidation resistant steel heat strength steel and air valve steel; c. Electric heating alloy steel; d. Wear resistant steel; e. Low temperature steel; f. Electrical steel.High density may not be obtained by simple pressurization, and insulation shall be carried out at the same time.The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.

When the vehicle is replaced with seamless square tube blank, the material is too soft to affect the requirements, so as to ensure the quality of parts and avoid wrinkles.For oil, the oil brush work shall be carried out in accordance with the requirements of the rule system, so as to ensure the oil brush and the oil in the correct position of the brush and avoid wrinkles.Ribnita,Cold formed hollow section steel (American Standard) for cold pressed QB square tube (national standard) structure carbon steel cold-formed circular section and pressure welded QB square tube and seamless QB square tube (European standard) non alloy fine grain cold formed welded hollow structural profile (Japanese standard) angle steel QB square tube for general structure galvanized qb square tube for low pressure fluid transmission, Standard No.: gbt-. Representative materials: qqbqb, etc. it is mainly used to transport water, gas, air, oil and water or steam. It is a special product manufacturing enterprise integrating R & D, and service. It has long been a professional square tube, square tube, seamless square tube, galvanized square tube and galvanized tube. Its purpose is only limited to general low-pressure fluid.A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.Jabbar OS salaj,C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.The strength, plasticity and angle discussed later are the machine function indicators of metal under static load. In practice, many mechanical machines are under repeated load, and the whole opportunity is tired in this environment.Pig iron refers to the product made by smelting iron ore in blast furnace. It is mainly used for steelmaking and square casting. Put the cast pig iron in the melting furnace to obtain cast iron (liquid), and cast the liquid cast iron into a cast square pipe. This kind of cast iron is called cast iron.

The other is designed with deformation angle, which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.The researcher's test before using the strip thinning drawing also confirmed that using the strip thinning drawing can greatly reduce the large value of tangential residual stress of the drawn parts and effectively prevent the occurrence of longitudinal cracking. According to different deformation degree and original sheet thickness, the appropriate thinning coefficient & psi is selected; N (generally .t ~ .t), if & psi; If n is too small, the deformation stress will increase sharply, resulting in the fracture of the bottom of the drawing part.Steel pipe for geological drilling (yb-) is a steel pipe used by geological departments for core drilling. It can be divided into drill pipe, drill collar, core pipe, casing, class II pressure pipe system, boiler and superheater. It is a long-term business square pipe, square pipe, seamless square pipe, galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃, and the working temperature of alloy steel square pipe wall shall exceed ℃.Hot dip galvanized square pipe is widely used, mainly in curtain wall, solar power generation support, construction, machinery and steel structure engineering, especially in curtain wall, machinery and construction. The effect of cold galvanized square tube is far from that of hot galvanized square tube; How to distinguish hot galvanized square pipe from cold galvanized square pipe?

Square tube is an essential material for the construction and Realization of industrialization. It is widely used and has a wide variety. According to different section shapes, square tube is generally divided into sections, plates, ordering and supply of square tube and do a good job in operation and management, it is also divided into heavy rail, light rail, large section steel, medium section steel, small section steel and square tube cold bending Section steel, high-quality section steel, wire rod medium and thick steel plate, sheet steel, electrical silicon steel sheet, strip steel, seamless steel pipe, square pipe, welded steel pipe, metal products etc.build,Ferroalloy is an alloy composed of iron and silicon, manganese,RibnitaPrice of DN100 galvanized pipe, titanium and other elements. Ferroalloy is the raw material for steelmaking. It is used as deoxidizer and alloy element additive for steel in square tube steelmaking.The strip caused by component segregation, that is, when the steel contains harmful impurities such as phosphorus and is pressed and delayed, the impurities elongate along the rolling direction. When the steel is cooled below , making the morphology of ferrite distributed in bands and then pearlite distributed in bands. This band can be eliminated by electroslag remelting and increasing crystallization speed.Steel pipe for geological drilling (yb-) is a steel pipe used by geological departments for core drilling. It can be divided into drill pipe, drill collar, core pipe, casing, sedimentation pipe, etc.Ribnita,Steel for construction and engineering according to the classification of use without phase transformation or partial phase transformation of square tube: A. ordinary carbon structural steel; b. Low alloy structural steel; c. Steel reinforcement.The other is designed with deformation angle which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.Square tube structural steel A. mechanical steel: (a) quenched and tempered structural steel; (b) Surface hardening structural steel: including carburized steel, ammoniated steel and surface quenching steel; (c) Easy to cut structural steel; (d) Steel for cold plastic forming: including steel for cold stamping and steel for cold heading.

special shaped square pipe is the general name of square pipes with other cross-section shapes except circular pipe. According to the different cross-section shape and size of steel pipe, it can be divided into special-shaped square pipe with equal wall thickness (code D), special-shaped square pipe with unequal wall thickness (code BD) and special-shaped seamless steel pipe with variable diameter (code D) These special-shaped large-diameter qb square tubes are widely used in various structural parts, special-shaped tubes generally have large moment of inertia and section modulus, and have large bending and torsion resistance, which can greatly reduce the structural weight and save steel. Square tubes are an indispensable part of construction workHigh temperature diffusion heat treatment of ingot can improve the composition heterogeneity of ingot and improve the transverse performance of square tube.Compared with other welding, square pipe welding has many advantages, mainly because of the exothermic reaction, the material only needs to be heated below the melting pointAdministration,The local heat release in the welding process of square tube can reduce the heat affected zone, and maintain the properties of materials.Empty bending empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.Square pipe for diamond core drilling (gb-) is a square pipe for drill pipe, core rod and casing for diamond core drilling.

Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner, resulting in an under current area. The zinc layer at this part is thin, and there is no zinc layer attached to the cold galvanized square pipe. The cold galvanized square pipe has no zinc lump and caking as a whole, but the overall zinc layer is thin, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer, and there will be water marks and a few zinc tumors, but the overall zinc layer is thick and the thickness of the zinc layer on the inner and outer walls of the square tube is -mu; M above. The nature of QB square tube!production,Ship carbon steel square pipe (gb-) is a carbon steel square pipe for ship class I pressure pipe system, class II pressure pipe system, boiler and superheater. It is a long-term business square pipe,monsanto Thin wall galvanized square pipe, square pipe,monsanto Price of galvanized seamless steel pipe, seamless square pipe, galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃, and the working temperature of alloy steel square pipe wall shall exceed ℃.The flattening speed of the sample can be ~ mmin.. fake and inferior square tubes are easy to fold. Folding is a variety of broken lines formed on the surface of square tubes, and this defect often runs through the longitudinal direction of the whole product. The reason for the folding is that the fake and shoddy manufacturers pursue the rate, the reduction is too large, resulting in ears, folding occurs during the next rolling, the folded products will crack after bending, and the strength of the square tube will be greatly reduced.monsanto ,High density may not be obtained by simple pressurization, and insulation shall be carried out at the same time.The floating mandrel mill is in its heydayIf there is only a single plane weld, the step-by-step back welding shall be adopted from the middle, that is, the arc of the section weld shall be terminated at the section arc.

Square tube heating process square tube calculates the chip thickness of workpiece. After each regrinding, the service life of the saw blade. Regrinding times of the saw blade. When the saw blade is replaced, the main drive AC motor spindle rotates stepless speed change AC motor feed capacity stepless speed change feed fast return to a constant value center system brush device hydraulic saw cutting system system system represents the quality RA flatness, large burr height cutting Chip length tolerance dimension: width and length . ~ .mm ~ m ~ ~ min kW ~ rpm ( kw ~ mmmin mmmin .kw .kw & times; kW S & mu; m . mm & plusmn; mm about mm about mm about mm high. The total weight of each billet square tube is seconds (including, pipe blank cutting, saw blade return, opening device, pipe blank discharge, head and tail cutting time, but excluding pipe blank transportation time). The large production capacity of the three saws is T / A. the pipe blank saw has a special reversing device (hydraulic servo device) to reduce vibration and improve the service life of the saw (only during feeding). The sawing machine has two devices distributed at the inlet and outlet (the input area is supported by roller table to ensure the bending of billet) The inlet end after sawing. Open it to ensure that the saw blade does not contact the blank when it returns. & mdash; feed saw gear & mdash; saw gear vibration reduction, which is composed of a fixed gear vibration reduction, as a movable vibration reduction to avoid the axial of the saw blade. & mdash; brush and sweep device & mdash; a driving brush and sweep device is installed at the bottom of the saw blade to clean the iron filings on the teeth and will not affect the service life of the saw blade. &Mdash; saw blade. In order to improve the service life of the saw blade, a small amount of high load agent container is atomized by air and poured on the saw blade without residue. & mdash; saw blade cooling device. A special nozzle is used to spray cold air at - oC on the saw blade. The cut-off blank is transferred to the buffer chain in front of the loader after passing through the outlet roller table and weighing device (Note: # before sawing, there is a feeding bench for single size billets that need to be cut, and after weighing, there is a feeding bench for returned billets). The buffer transfer chain transports the billets to the lower roller table of the loader. The billets are turned over from the chain to the roller table by the turnover hook. The weighed qualified billets are loaded into the annular furnace by the loader, and the weighed unqualified billets are transported from the roller table to the removal bench for removal.Pull square tube:Barreiro ,In the process of processing, the processing temperature is the key. Professional square tube, square tube seamless square tube, galvanized square tube and galvanized tube have advanced technology, more affordable price and more preferential price. Consultation is welcome. It must be noted that the blank heating should be uniform. Perforation has a great impact on the quality. The perforation temperature of blank varies according to different materials, generally around ℃. special shaped square pipe is the general name of square pipes with other cross-section shapes except circular pipe. According to the different cross-section shape and size of steel pipe, it can be divided into special-shaped square pipe with equal wall thickness (code D),Barreiro 40 galvanized square pipe specification, special-shaped square pipe with unequal wall thickness (code BD) and special-shaped seamless steel pipe with variable diameter (code D) These special-shaped large-diameter qb square tubes are widely used in various structural parts, tools and mechanical parts. Compared with circular tubes, special-shaped tubes generally have large moment of inertia and section modulus, and have large bending and torsion resistance,Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner, resulting in an under current area. The zinc layer at this part is thin, and there is no zinc layer attached to the cold galvanized square pipe. The cold galvanized square pipe has no zinc lump and caking as a whole, but the overall zinc layer is thin, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer and there will be water marks and a few zinc tumors, but the overall zinc layer is thick, and the thickness of the zinc layer on the inner and outer walls of the square tube is -mu; M above. The nature of QB square tube!The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.Ship carbon steel square pipe (gb-) is a carbon steel square pipe for ship class I pressure pipe system, class II pressure pipe system, boiler and superheater. It is a long-term business square pipe, square pipe, seamless square pipe, galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃, and the working temperature of alloy steel square pipe wall shall exceed ℃.

Viewing color: the color of the cold galvanized square tube is yellowish green, cyan white or slightly colored at a fixed angle with the sun. The color of hot-dip galvanized square pipe is silver white at a fixed angle with the sun.Effective treatment of square tube coating & ldquo; Surface defense line & rdquo; Surface technology and measures square tube coating is used as the back course & ldquo; Surface defense line & rdquo; The surface treatment technologies and measures can be carried out on the basis of other surface treatment technologies or processes. Here's the & ldquo; Surface treatment before coating & rdquo; It refers to all treatment measures for preparation for coating or joint protection with coating. Therefore, the surface treatment before coating is also called coating surface pretreatment.. fake and inferior square tubes are easy to fold. Folding is a variety of broken lines formed on the surface of square tubes, and this defect often runs through the longitudinal direction of the whole product. The reason for the folding is that the fake and shoddy manufacturers pursue the rate, the reduction is too large, resulting in ears folding occurs during the next rolling, the folded products will crack after bending, and the strength of the square tube will be greatly reduced.Which one is better,Square tube plays an important role in the rapid economic development. The functions of square tube are different, and its characteristics are also different. Square tube has strict standards. There are many welding processes and advantages of square tube. Let me show you the welding process and advantages of lower tube.Purpose of square tube the purpose of square tube includes construction, machinery, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, electric products ( pieces)Section shape classification of large-diameter qb square tube square tube is classified according to section shape: simple section square tube & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Flower shaped square pipe, open square pipe, corrugated square pipe, special-shaped square pipe, large-diameter qb square pipe surface treatment classification square pipe is divided according to surface treatment: hot-dip galvanized square pipe electro galvanized square pipe, oil coated square pipe, acid pickling square pipe, large-diameter qb square pipe purpose classification square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machine tool equipment, chemical industry, steel structure, shipbuilding, automobile,Barreiro High strength square tube, steel beam and column, large-diameter qb square tube wall thickness classification, large-diameter qb square tube according to wall thickness Classification & mdash& mdash; Super large diameter qb square pipe, large diameter qb square pipe and thin-wall large diameter qb square pipe rectangular pipe are the names of square pipe and QB square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment. Generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Usually pieces per bag. Qb square pipe, also known as square and rectangular cold-formed hollow section steel,Barreiro Square tube right angle, is referred to as square pipe and rectangular pipe code f and j respectively. The allowable deviation of wall thickness of qb square pipe shall not exceed plus or minus % of nominal wall thickness when the wall thickness is not greater than mm, plus or minus % of wall thickness when the wall thickness is greater than mm, except for the wall thickness of corner and welding joint area.

The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.Welcome calls ,The disadvantage of empty bending is that when the upper side and side are synchronously empty bending, the forming force is easy to exceed the critical point due to the pressure generated by the upper roll and the lower roll at the same time, resulting in edge instability and concave, and will also affect the stable operation and forming quality of the unit. This is also the different characteristics of qb square tube and round tube empty bending. The concept of square tube: square tube is the pressure processing of ingot billet or square tube Make materials of all shapes, sizes and properties we need.The new improvement ensures that square tubes can be used for a long time. With the development of the times, I'll introduce the process of lower tubes.If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.Barreiro ,Oil drilling pipe (yb-) is a square pipe used for internal or external thickening at both ends of oil drilling. Steel pipes are divided into turning wire and non turning wire. Turning wire pipe is connected with joint, and non turning wire pipe is connected with tool joint by butt welding.Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, plates and tubes. It is divided into cold rolling and hot rolling.For gas transmission: gas

Hardness hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Generally speaking,CoroosGalvanized square pipe joint, pressurization and thermal insulation.Coroos,At present, researchers at home and abroad have carried out experimental discussion on the anti adhesion of square tube surface. So far, there is still a lack of research on surface adhesion, there is no systematic and perfect theory to guide the preparation of anti adhesion inner surface of pipeline, and there is a lack of operable and low-cost inner surface preparation technology of square pipe. In terms of solid surface adhesion mechanism, based on the solid-liquid interface adhesion work theory and smooth solid surface model, this paper analyzes the spreading process on machined rough surface, studies the dynamic movement characteristics of solid-liquid vapor phase line, directly analyzes the adhesion process, and establishes a line spreading model based on small system energy, It provides theoretical guidance for the preparation of anti adhesion surface of pipeline.Fake and shoddy square tubes are easy to scratch, because the equipment of fake and shoddy material manufacturers is simple and easy to produce burrs and scratch the surface of square tubes. Deep scratches reduce the strength of square tubes.Madrid,The other is designed with deformation angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.Square pipe welding is suitable for surface treatment of materials. Square pipe welding can be used for ceramic ceramic, metal ceramic and metal metal welding.It should be noted that the position of the disc from the calibration line can be adjusted according to the reinforcement diameter,CoroosQ235 hot dip galvanized square pipe, and R and R can be equal or different.

The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.Chemical polishing: less investment in processing equipment, high speed, high efficiency and good durability. Its defects are poor brightness gas overflow, demand for ventilation equipment and difficult heating. It is suitable for processing small batch of disordered parts and products with low brightness demand for small parts.The square tube for fluid transportation (gbt-) is a general square tube for transporting water, oil, gas and other fluids.High quality and low price,Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).In recent years, the continuous casting process of large-diameter seamless square tubes is also different. What are the specific steps of the continuous casting process of large-diameter seamless square tube? As the name suggests, square tube is a kind of square tube type. Many materials can form square tube body. Its medium is used for what purpose and where it is used. Most square tubes are steel tubes which are unpacked, leveled, crimped and welded to form round tubes, Then the round pipe is rolled into a square pipe, square tubes per package are mostly in large specifications in terms of spot, and . - ~~ - square tubes are divided into structural square tubes, decorative square tubes, building square tubes, mechanical square tubes, etc. according to their uses.

C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.The cost is reasonable,Normalized: A. pearlite steel; b. Bainitic steel; c. Martensitic steel; d. Austenitic steel.In fact, the casting cleaning is not just shot blasting. For large parts, the drum sand cleaning is carried out first, that is, the riser of the casting is cut off and rolled in the drum, and the square tubes collide with each other in the drum to remove most of the sand on the surface before shot blasting or shot blasting.Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. Seamless pipe can be divided into hot rolled pipe and cold rolled pipe according to different productionCoroos,CoroosGalvanized square pipe and rectangular pipe,Improve the positioning and pre bending steps, if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap resulting in uneven walking feeding.Due to the increase of square tube production, there are more and more fake and shoddy square tubes in the market. How to distinguish the fake and shoddy square tubes? Let me teach you some points to distinguish the fake and shoddy square tubes.A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.

Hundreds of degrees Celsius, which can save energy.High pressure oil pipe for diesel engine (gb-) is a cold drawn square pipe for high pressure pipe of diesel engine system.amora ,In & sigma; Expressed in%. The calculation formula is: where: L -- gauge length after sample breaking, mm; L -- original gauge length of sample, mm. Reduction of area (& psi;) in the tensile test, the percentage between the large reduction of the cross-sectional area at the reduced diameter and the original cross-sectional area after the specimen is broken is called the reduction of area. In & psi; Expressed in%. The calculation formula is as follows: where: S -- original cross-sectional area of the sample, mm; S -- small cross-sectional area at the reduced diameter after sample breaking, mm.Improve the positioning and pre bending steps, if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.Asyut,Improve the positioning and pre bending steps, if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.The other is designed with deformation angle, which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.Ferroalloy is an alloy composed of iron and silicon, manganese,amora Galvanized steel square pipe,amora Specification and size of galvanized flat pipe, chromium, titanium and other elements. Ferroalloy is the raw material for steelmaking. It is used as deoxidizer and alloy element additive for steel in square tube steelmaking.

Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, plates and tubes. It is divided into cold rolling and hot rolling.Except for the thickening of wall thickness, the corner size and edge straightness of square pipe reach or even exceedSquare tube is made of different materials. It needs qualified inspection by relevant staff before leaving the factory. Square tube has a wide range of uses. Its main field is not only the construction industry, and cast the liquid cast iron into a cast square pipe. This kind of cast iron is called cast iron.The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.Cleaning solvent and emulsion can clean the surface of square tube to remove oilPig iron refers to the product made by smelting iron ore in blast furnace. It is mainly used for steelmaking and square casting. Put the cast pig iron in the melting furnace to obtain cast iron (liquid), grease, agent and similar organic matter,amora Seamless galvanized square pipe, but it can not remove rust, scale welding, etc. on the surface of square tube, so it is only used as an auxiliary means in production.

In this period, the technology of continuous rolling pipe was not mature.Honesty is the foundation,Square tube is made of different materials. It needs qualified inspection by relevant staff before leaving the factory. Square tube has a wide range of uses. Its main field is not only the construction industry but also can be seen everywhere in our daily life. The service life of square tubes is mainly affected by surface treatment. I will explain the specific operations of surface treatment of square tubes.How to specify the yield point of square tube: if the stress decreases, the upper and lower yield points shall be distinguished. The unit of yield point is nmm (MPA). Upper yield pointBrinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.amora ,Square pipe for conveying flammable and non flammable fluids, Standard No.: gbt (gbt - ). The representative material is l-l pipeline steel. It is mainly used to transport flammable and non flammable fluids. Low pressure or high pressure square pipes have high requirements. The purpose of large-diameter qb square pipe is qb square pipe, C-shaped steel and H-shaped steel. It is mainly used in the construction of simple plant, steel structure and other infrastructure. Qb square pipe is generally used as the frame and purlin of the plant. C-shaped steel Steel is an important support for the plant, and H-section steel is used as load-bearing. Especially in recent years, a large number of small and medium-sized enterprises have started to build spacious and bright plants. If traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises, if the investment in the plant is too high, the capital will be produced after operation Serious impact. The plant built with qb square tube, C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, the sales of qb square tube, C-section steel and H-section steel have increased significantly in recent years and become the first choice for plant construction. Qb square tube, C-section steel and H-section steel are mainly used in the construction of simple plant, steel structure and other infrastructure The qb square tube is used as the frame and purlin of the plant. The C-shaped steel is used as the important support of the plant, and the H-shaped steel is used as the load-bearing. Especially in recent years, a large number of small and medium-sized enterprises around the country have started to build spacious and bright plants. If the traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises Said that if the investment in the plant is too high it will have a serious impact on the capital after operation. The plant built with qb square pipe, money saving and fast use. Therefore, the sales of qb square pipe, C-section steel and H-section steel have increased significantly in recent years, even when the wrinkle around the part is determined to be less than the clamping force, and the gradual increase of the roll gap force can be. When drawing the cone and hemispherical components, it should be increased to increase the inner diameter of the inner plate and the tensile stress of the wrinkle drawbead. Adopt the principle of loosening after tightening to loosen after tightening and ask Question.Precision inner diameter square tubes for hydraulic and pneumatic cylinders (gb-) are cold drawn or cold-rolled precision square tubes with precision inner diameter for hydraulic and pneumatic cylinders.The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.

Functional index analysis of qb square tube - mechanical function of plastic square tube. Solid bending, as the name suggests, is to compact the bending. During real bending, the inner and outer rollers and the inner and outer walls of the pipe blank are compacted in both directions.After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, so as to improve yield strength and save steel.zebraFunction index analysis of square tube - the strength acts on the parts in a great progress. The load on the parts is called the charge and trap load. The power of square tube destruction under the charge and trap load is called the charge and trap toughness.Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.Oskemen,Stainless steel square tube for fluid transportation (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square tube made of stainless steel for fluid transportation.Stage ( & mdash; )There are many processing technologies for square tubes. I won't introduce the specific processing technology here. We only know about the processing technology of each other's tubes. We may have insufficient understanding of its heating technology. Next, I'll give you a detailed introduction to the heating technology of the lower tubes.

Main uses of square tube: square tube is mainly used in tap water engineering,zebra38 galvanized pipe, petrochemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products developed.However, there is a large rate of end in the application of steel pipe, which is mainly due to the trouble of internal and external treatment. The primary external question is very crucial, and its external quality directly affects its applicationSquare tube modified square tube, square tube, QB square tube and hot-rolled square tube are qualified in quality inspection. The manufacturer adopts advanced equipment to ensure the quality of each product. Magnetic flux leakage testing for surface defects of square tubes is very similar to magnetic particle testing for square tubes, and its scope of application, sensitivity and reliability are stronger than magnetic particle testing. Indirect square forming process the traditional forming process of cold-formed square pipe is to gradually roll the hot-rolled steel coil multi stand forming unit into round pipe at room temperature, and then the shaping unit will roll the round pipe into square pipe, which is called indirect square forming process. The traditional roll forming process uses the method of fixed bending point position and variable bending radian to complete the corner forming of pipe blank, which is suitable for rolling small and medium-sized products. Rolling with this process & ldquo; Superb & rdquo; Square tube will show its inherent defects. Because the roll work in the bending process of this process is always concentrated at the point, excessive stress concentration often shows microcracks in the bending process of profiles, which will lead to cracking in serious cases. The products with such defects have serious consequences when they are used in building steel structures. The study of the broken square tube column in the Hanshin earthquake in Japan shows that the corner microcrack is the main cause of the square tube fracture. At the same time, due to the different forming bending radians of products with different wall thickness, the universality of rolls is limited. The large-size cold-formed square tube used in the process adopts the advanced & ldquo; Direct Square & rdquo; The production process is to directly roll the hot-rolled steel coil into a square and rectangular shape at room temperature.Where can I find it?,Square tube heating process square tube calculates the chip thickness of workpiece. After each regrinding, the service life of the saw blade. Regrinding times of the saw blade. When the saw blade is replaced, the main drive AC motor spindle rotates stepless speed change AC motor feed capacity stepless speed change feed fast return to a constant value center system brush device hydraulic saw cutting system system system represents the quality RA flatness, large burr height cutting Chip length tolerance dimension: width and length . ~ .mm ~ m ~ ~ min kW ~ rpm ( kw ~ mmmin mmmin .kw .kw & times; kW S & mu; m . mm & plusmn; mm about mm about mm about mm high. The total weight of each billet square tube is seconds (including pipe blank cutting, opening device saw blade return, pipe blank discharge, head and tail cutting time, but excluding pipe blank transportation time). The large production capacity of the three saws is T / A. the pipe blank saw has a special reversing device (hydraulic servo device) to reduce vibration and improve the service life of the saw (only during feeding). The sawing machine has two devices distributed at the inlet and outlet (the input area is supported by roller table to ensure the bending of billet) The inlet end after sawing. Open it to ensure that the saw blade does not contact the blank when it returns. & mdash; feed saw gear & mdash; saw gear vibration reduction, which is composed of a fixed gear vibration reduction, as a movable vibration reduction to avoid the axial of the saw blade. & mdash; brush and sweep device & mdash; a driving brush and sweep device is installed at the bottom of the saw blade to clean the iron filings on the teeth and will not affect the service life of the saw blade. &Mdash; saw blade. In order to improve the service life of the saw blade, a small amount of high load agent container is atomized by air and poured on the saw blade without residue. & mdash; saw blade cooling device. A special nozzle is used to spray cold air at - oC on the saw blade. The cut-off blank is transferred to the buffer chain in front of the loader after passing through the outlet roller table and weighing device (Note: # before sawing, there is a feeding bench for single size billets that need to be cut, and after weighing, there is a feeding bench for returned billets). The buffer transfer chain transports the billets to the lower roller table of the loader. The billets are turned over from the chain to the roller table by the turnover hook. The weighed qualified billets are loaded into the annular furnace by the loader, the surface should be cleaned with solvent or emulsion. Square pipes of various specifications, square rectangular pipes, seamless square pipes, galvanized square pipes, galvanized pipes are supplied in time and cost-effective. They have become the preferred brand of many wire products. Welcome to buy! It is used to remove oil and dust. It is only suitable for removing grease and dust on the surface of square pipe,zebraGalvanized thick square pipe, which can not remove rust and oxide scale. Therefore, it can only be used as an auxiliary means in production.Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.

Square tube heating process square tube calculates the chip thickness of workpiece. After each regrinding, the service life of the saw blade. Regrinding times of the saw blade. When the saw blade is replaced, the main drive AC motor spindle rotates stepless speed change AC motor feed capacity stepless speed change feed fast return to a constant value center system brush device hydraulic saw cutting system system system represents the quality RA flatness, large burr height cutting Chip length tolerance dimension: width and length . ~ .mm ~ m ~ ~ min kW ~ rpm ( kw ~ mmmin mmmin .kw .kw & times; kW S & mu; m . mm & plusmn; mm about mm about mm about mm high. The total weight of each billet square tube is seconds (including, pipe blank cutting, opening device, pipe blank discharge, head and tail cutting time, but excluding pipe blank transportation time). The large production capacity of the three saws is T / A. the pipe blank saw has a special reversing device (hydraulic servo device) to reduce vibration and improve the service life of the saw (only during feeding). The sawing machine has two devices distributed at the inlet and outlet (the input area is supported by roller table to ensure the bending of billet) The inlet end after sawing. Open it to ensure that the saw blade does not contact the blank when it returns. & mdash; feed saw gear & mdash; saw gear vibration reduction, which is composed of a fixed gear vibration reduction, a small amount of high load agent container is atomized by air and poured on the saw blade without residue. & mdash; saw blade cooling device. A special nozzle is used to spray cold air at - oC on the saw blade. The cut-off blank is transferred to the buffer chain in front of the loader after passing through the outlet roller table and weighing device (Note: # before sawing, there is a feeding bench for single size billets that need to be cut, and after weighing, there is a feeding bench for returned billets). The buffer transfer chain transports the billets to the lower roller table of the loader. The billets are turned over from the chain to the roller table by the turnover hook. The weighed qualified billets are loaded into the annular furnace by the loader, and the weighed unqualified billets are transported from the roller table to the removal bench for removal.Honesty is the foundation,Solution treatment and nondestructive testing sand rolling treatment and sand blasting treatment many manufacturers in the market do not do solution treatment and % penetration nondestructive testing, and many of them use sand blasting instead of sand rolling. After these steps are omitted, the cost is greatly reduced.High hardness square tubes mainly bear fatigue load, so they must have high hardness. Therefore quenching, surface quenching or chemical heat treatment shall be carried out, mainly in curtain wall, solar power generation support, construction, machinery and steel structure engineering, especially in curtain wall,zebra16 square tube, machinery and construction. The effect of cold galvanized square tube is far from that of hot galvanized square tube; How to distinguish hot galvanized square pipe from cold galvanized square pipe?zebra,The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.The square tube for fluid transportation (gbt-) is a general square tube for transporting water, oil, gas and other fluids.For oil, the oil brush work shall be carried out in accordance with the requirements of the rule system, so as to ensure the oil brush and the oil in the correct position of the brush and avoid wrinkles.

If there is only a single plane weld, the step-by-step back welding shall be adopted from the middle, that is, the arc of the section weld shall be terminated at the section arc.Engaged in square tube, square rectangular tube, seamless square tube, galvanized square tube, galvanized tube, old brand, price advantage and quality guarantee! However the Demander shall cut off the interface pipe when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square pipe with theoretical weight greater than kgm, it shall not exceed % of the total delivery. The bending degree of qb square pipe shall not be greater than mm per meter, and the total bending degree shall not be greater than .% of the total length. Galvanized qb square pipe for low-pressure fluid transmission, with standard number of gbt-. Representative materials: QA, qbqb, etc. It is mainly used for conveying water, gas, air, oil and heating hot water or steam, and its purpose is limited to general low pressure fluid.Slema,Square tube flattening test is a kind of test to check the deformation performance of metal tubes (seamless square tubes and rectangular tubes) flattened to the specified size and show their defects. Relevant flattening tests shall be carried out in accordance with relevant provisions of test standards. Requirements for samples samples can be taken from metal pipes with qualified appearance. Generally, sawing is adopted. The inner and outer walls of the pipe shall retain the original surface without any processing. Sample length L & asymp; D (D is the outer diameter of the pipe). When the outer diameter is large, the length l shall not exceed mm. When the outer diameter is less than mm, l = mm. When cutting the sample, the surface of the sample shall not be damaged and the performance of the metal shall not be changed due to heating or cold processing. The edge of the section shall be flattened. The flattening test is a test to check the deformation performance of the metal pipe (seamless square pipe and rectangular pipe) flattened to the specified size and show its defects. Relevant flattening tests shall be carried out in accordance with relevant provisions of test standards. special shaped square pipe is the general name of square pipes with other cross-section shapes except circular pipe. According to the different cross-section shape and size of steel pipe, it can be divided into special-shaped square pipe with equal wall thickness (code D), special-shaped square pipe with unequal wall thickness (code BD) and special-shaped seamless steel pipe with variable diameter (code D) These special-shaped large-diameter qb square tubes are widely used in various structural parts, tools and mechanical parts. Compared with circular tubes, special-shaped tubes generally have large moment of inertia and section modulus and have large bending and torsion resistance, which can greatly reduce the structural weight and save steel. Square tubes are an indispensable part of construction workSuphan Buri,Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. Seamless pipe can be divided into hot rolled pipe and cold rolled pipe according to different productionFunctional index analysis of qb square tube - angular plasticity refers to the power of plastic deformation (permanent deformation) without destruction of qb square tube data under load.Structural stainless steel square pipe (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square pipe made of stainless steel for corrosion-resistant pipes, structural parts and parts widely used in chemical, petroleum, light textile, food,SlemaRepresentation of galvanized square pipe, machinery and other industries.

Stage ( & mdash; )Shot blasting and sand blasting are widely used in repair and shipbuilding industry. However whether shot blasting or sand blasting, compressed air is used. Professional square pipe, square rectangular pipe, seamless square pipe, galvanized square pipe, galvanized pipe has high pressure resistance grade, good waterproof performance, fire and high temperature resistance, strong overload capacity, corrosion resistance, radiation protection and long service life. Of course, it is not shot blasting, so it is necessary to use high-speed rotating impeller. In the repair and shipbuilding industry, shot blasting (small steel shot) is mostly used in square pipe pretreatment (rust removal before coating); Sand blasting (mineral sand is used in repair and shipbuilding) is mostly used in formed ships or sections to remove the old paint and rust on the square tube and repaint it. In the repair and shipbuilding industry, the main function of shot blasting and sand blasting is to increase the adhesion of square tube coating paint.Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally,SlemaSquare pipe galvanized square pipe, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid, alkali, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, rail, steel plate, large-diameter steel pipe, forging, etc. can be stacked in the open air; Small and medium-sized section steel, medium diameter steel pipe reinforcement steel wire and steel wire rope can be stored in a well ventilated shed, steel sheets, silicon steel sheets, or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, and generally adopts ordinary closed warehouse, that is, the warehouse with roof enclosure, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, loading and unloading and shall not be damaged, The storage period of materials can be extended, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel, alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, it can reflect that the square tube is good. On the contrary, if the surface is not goodindex,C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.Cleaning solvent and emulsion can clean the surface of square tube to remove oil, grease, dust agent and similar organic matter, but it can not remove rust, welding, A. open hearth steel: (a) acid open hearth steel; (b) Alkaline open hearth steel.

There are many ways of ignition, such as arc, electric spark, flame, strong current, high-temperature furnace, laser, high-temperature radiation, microwave, chemical furnace, etc.production costs,Put the pig iron for steelmaking into the steelmaking furnace according to the specified process to obtain steel. The products of steel include ingots, continuous casting billets and various steel castings made of straight square tubes. Generally speaking, steel refers to the steel rolled into various square tubes. Square tube steel belongs to ferrous metal, but steel is not completely equal to ferrous metal.The inclusions in the square tube treated with calcium can be denatured well, and the morphology of sulfide in the rolled stock is also improved.Structural stainless steel square pipe (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square pipe made of stainless steel for corrosion-resistant pipes, structural parts and parts widely used in chemical, petroleum, light textile, food, machinery and other industries.Slema,At this time, it shall be welded to the fixed thickness, ground and sandblasted, and repair welding shall be adopted where there are cracks, even if the steel pipe with another large opening can be made up at one time.The surface of fake and inferior square tubes is easy to produce scabs. There are two reasons: the material of fake and inferior square tubes is uneven and there are many impurities. The guide equipment of fake and shoddy material manufacturers is simple and easy to stick to steel. These impurities are easy to scar after biting the roll. special shaped square pipe is the general name of square pipes with other cross-section shapes except circular pipe. According to the different cross-section shape and size of steel pipe, special-shaped square pipe with unequal wall thickness (code BD) and special-shaped seamless steel pipe with variable diameter (code D) These special-shaped large-diameter qb square tubes are widely used in various structural parts, tools and mechanical parts. Compared with circular tubes, special-shaped tubes generally have large moment of inertia and section modulus, and have large bending and torsion resistance which can greatly reduce the structural weight and save steel. Square tubes are an indispensable part of construction work

When the vehicle is replaced with seamless square tube blank, so as to ensure the quality of parts and avoid wrinkles.The second is to clean the surface of the opposite pipe. When cleaning the opposite pipe, the surface should be cleaned with solvent or emulsion. Square pipes of various specifications, square rectangular pipes, seamless square pipes, galvanized square pipes, galvanized pipes are supplied in time and cost-effective. They have become the preferred brand of many wire products. Welcome to buy! It is used to remove oil and dust. It is only suitable for removing grease and dust on the surface of square pipe, which can not remove rust and oxide scale. Therefore, it can only be used as an auxiliary means in production.Aveiro ,Aveiro Price of galvanized 40 square pipe,There are several kinds of color qb square tubes: high temperature oxidation method, chemical oxidation method, electrochemical oxidation method, ion implantation method and gas phase cracking method.Precision inner diameter square tubes for hydraulic and pneumatic cylinders (gb-) are cold drawn or cold-rolled precision square tubes with precision inner diameter for hydraulic and pneumatic cylinders.Jhang Sadr,Ship carbon steel square pipe (gb-) is a carbon steel square pipe for ship class I pressure pipe system, class II pressure pipe system, boiler and superheater. It is a long-term business square pipe square pipe, seamless square pipe, galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃, and the working temperature of alloy steel square pipe wall shall exceed ℃.The first is to remove the rust of the square tube. When removing the rust of the square tube, the steel wire brush is mainly used to polish its surface, which can effectively remove the loose or rusty rust on the surface of the square tube.Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.

Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.The flattening speed of the sample can be ~ mmin., cold drawn tubes, tubes, etc. Hot rolled seamless tubes are produced on the automatic precision tube precision tube rolling mill. The solid tube blank is cut into the required length by removing surface defects, centering on the end face of the perforated end of the tube blank, and then sent to the heating furnace for heating. It is perforated on the piercing machine. At the same time, it rotates and advances continuously under the action of roll and plug, A cavity is gradually formed inside the pipe blank, which is called the rough pipe, and then sent to the automatic pipe mill for continuous rolling. After the wall thickness is adjusted by the whole machine, and the diameter is determined by the sizing machine to meet the specification requirements. The continuous pipe mill is more advanced in producing hot-rolled seamless steel pipe. If you want to obtain seamless pipe with smaller size and better quality, Cold rolling and cold drawing must be adopted, or the combination of cold rolling and cold drawing is usually carried out on the roll mill. The seamless pipe is rolled in the annular pass composed of variable section circular hole groove and fixed conical plug. Cold drawing is usually carried out on the single chain or double chain cold drawing machine,Aveiro 43 galvanized pipe, that is, the heated pipe blank is placed in a closed cylinder, and the perforated rod and rod move, This method can produce steel pipe with small diameter. In the building materials industry, the development of various pipes is different. Because of their different characteristics, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. We need to understand the various characteristics of steel pipes. However, in the building materials industry, the development of various pipes is different. Because of their different characteristics, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. The various characteristics of steel pipe need to be understood by everyone. However, due to the of steel pipe and other raw materials, the storage of steel pipe needs specific conditions.High quality and low price,Section shape classification of large-diameter qb square tube square tube is classified according to section shape: simple section square tube & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Flower shaped square pipe, corrugated square pipe, special-shaped square pipe, large-diameter qb square pipe surface treatment classification square pipe is divided according to surface treatment: hot-dip galvanized square pipe, electro galvanized square pipe, oil coated square pipe, acid pickling square pipe, large-diameter qb square pipe purpose classification square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machine tool equipment, machinery industry, chemical industry,Aveiro Q345B seamless square tube, automobile shipbuilding, steel beam and column, special purpose, large-diameter qb square tube wall thickness classification large-diameter qb square tube according to wall thickness Classification & mdash& mdash; Super large diameter qb square pipe, large diameter qb square pipe and thin-wall large diameter qb square pipe rectangular pipe are the names of square pipe and QB square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment. Generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Usually pieces per bag. Qb square pipe, also known as square and rectangular cold-formed hollow section steel, is referred to as square pipe and rectangular pipe, code f and j respectively. The allowable deviation of wall thickness of qb square pipe shall not exceed plus or minus % of nominal wall thickness when the wall thickness is not greater than mm, plus or minus % of wall thickness when the wall thickness is greater than mm, except for the wall thickness of corner and welding joint area.B. low alloy structural steel C. ordinary structural steel and high-quality steel for specific purposes (including high-quality steel)The pipeline is only subject to chemical pickling, which can remove oxide scale, rust and old coating. Sometimes it can be used as the reprocessing after sand blasting. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the surrounding environment. The square tube shall be submitted for acceptance in batches, and the batch rules shall comply with the provisions of corresponding product standards.

Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).Process inspection,Superior square tubular steel (both P and s ≤ .%)Process flow of square tube drawing: because the size of the die hole of the square tube drawing is smaller than the outer diameter of the tube in front of the drawing, in order to make the front end of the square tube pass through the die hole smoothly, so that the clamp jaw of the drawing trolley can the head of the square tube, it is necessary to sharpen the head of the square tube before drawing. Therefore, the end of the square tube with a fixed length should be heated in the slit heating furnace, It is generally ~ mm, and the heating temperature is between ~ ℃ according to different wall thickness. Then use ~ kg air hammer to sharpen and grind the head of the square pipe. Generally, the square pipe with diameter less than mm can be sharpened by rotary forging hammer or roll forging machine.C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.Aveiro , the supplier can submit them for acceptance one by one; Or re conduct heat treatment (the number of RE heat treatment shall not exceed times), cold drawn tubes, tubes, etc. Hot rolled seamless tubes are produced on the automatic precision tube precision tube rolling mill. The solid tube blank is cut into the required length by removing surface defects, centering on the end face of the perforated end of the tube blank and then sent to the heating furnace for heating. It is perforated on the piercing machine. At the same time, A cavity is gradually formed inside the pipe blank, which is called the rough pipe, and then sent to the automatic pipe mill for continuous rolling. After the wall thickness is adjusted by the whole machine, and the diameter is determined by the sizing machine to meet the specification requirements. The continuous pipe mill is more advanced in producing hot-rolled seamless steel pipe. If you want to obtain seamless pipe with smaller size and better quality, Cold rolling and cold drawing must be adopted, or the combination of cold rolling and cold drawing is usually carried out on the roll mill. The seamless pipe is rolled in the annular pass composed of variable section circular hole groove and fixed conical plug. Cold drawing is usually carried out on the single chain or double chain cold drawing machine, the heated pipe blank is placed in a closed cylinder, and the perforated rod and rod move, This method can produce steel pipe with small diameter. In the building materials industry, the development of various pipes is different. Because of their different characteristics, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. We need to understand the various characteristics of steel pipes. However, in the building materials industry, the development of various pipes is different. Because of their different characteristics, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. The various characteristics of steel pipe need to be understood by everyone. However, due to the of steel pipe and other raw materials, the storage of steel pipe needs specific conditions.Stage ( & mdash; )

Cold drawn or cold rolled precision square tube (gb-) is a cold drawn or cold rolled precision square tube with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision square mechanical structure or hydraulic equipment can greatly save machining hours improve material rate and improve product quality.According to metallographic classification, the annealed state of square tube: A. hypoeutectoid steel (ferrite + pearlite); b. Eutectoid steel (pearlite); c. Steel precipitation through a common square tube (pearlite + cementite); d. Ledeburite steel (pearlite + cementite).Zejtun ,The banding caused by component segregation is difficult to be eliminated by heat treatment. Generally, normalizing can correct the segregation to the allowable level. If the banding is serious, it can be improved by multiple normalizing. It is reliable to conduct high-temperature diffusion annealing first and then normalize again, which can completely eliminate the strip but the cost will be very high, which is difficult to achieve for the steel plate due to the surface quality.Square pipe is the name of square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment.Anju,Impact toughness the load acting on the machine part at a great speed by QB is called impact load, and the ability of metal under impact load is called impact toughness.Hardness QB square hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Superior square tubular steel (both P and s ≤ .%)

Square tube is an essential material for the construction and Realization of industrialization. It is widely used and has a wide variety. According to different section shapes, square tube is generally divided into sections, plates, pipes and metal products. In order to facilitate the production, ordering and supply of square tube and do a good job in operation and management, it is also divided into heavy rail, light rail, large section steel, medium section steel small section steel and square tube cold bending Section steel, high-quality section steel, wire rod, medium and thick steel plate, sheet steel, electrical silicon steel sheet, strip steel, seamless steel pipe, square pipe, welded steel pipe, metal products etc.The qb square tube rolled from the strip steel through process treatment is generally to unpack, curl and weld the strip steel to form a round tube, then roll the round tube into a square tube, and then cut it to the required length. Nowadays, the forming of qb square tube has solid bending and empty bending. The bending degree of qb square tube shall not be greater than mm per meter, and the total bending degree shall not be greater than the actual bending of the total length. As the name suggests, the bending is compacted, and the internal and external rollers and the internal and external walls of the tube blank are compacted in both directions during the actual bending.Square pipe is the name of square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment.query,QB square tube is a product appeared in recent years, which mainly has strict tolerance and roughness for the dimensions of inner hole and outer wall. Production process classification of large-diameter qb square tube large-diameter qb square tube is divided into hot-rolled seamless square tube, cold drawn seamless square tube, seamless square tube and qb square tube according to production process. Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe,Zejtun 6 points galvanized water pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Material classification of straight seam welded square pipe and spiral welded square pipe large diameter qb square pipe: plain carbon steel square pipe and low alloy square pipe. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, Q, St-, etc.Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).During the pushing process of spot welding and repair welding elbows, there will be thinning, so manufacturers usually use thick spot pipes. If thin raw materials are used, the products produced must be unqualified. Generally, the thickness is significantly lower than the standard.

B. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.Production department,Zejtun Galvanized pipe manufacturer,Fake and shoddy square tubes are easy to scratch, because the equipment of fake and shoddy material manufacturers is simple and easy to produce burrs and scratch the surface of square tubes. Deep scratches reduce the strength of square tubes.It is feasible to use the theory to calculate static structures, houses and bridges, but it is not suitable for moving components such as wheels. At this time, people often use the plastic theory. The research of the plastic theory can be traced back to . In , the European Design Association formulated a plastic design code, which is mainly used for static load plane beams and frame structures subjected to bending stress The solution is as follows: for high-rise buildings, more detailed calculations are needed.Steel used & mdash& mdash; Such as bridge steel, ship steel, boiler steel, pressure vessel steel, agricultural machinery steel, etc.Zejtun There are many processing technologies for square tubes. I won't introduce the specific processing technology here. We only know about the processing technology of each other's tubes. We may have insufficient understanding of its heating technology. Next, I'll give you a detailed introduction to the heating technology of the lower tubes.B. spring steel C. bearing steel tool steel: A. carbon tool steel; b. Alloy tool steel; c. High speed tool steel.Generally,Zejtun Galvanized water pipe model, chemical and electrolytic pickling are used for pickling treatment. Only chemical pickling is used for pipelines, which can remove oxide scale, rust and old coatings. Professional square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes are safe, environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted. Sometimes they can be used as reprocessing after sand blasting and rust removal. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the environment.

The technology of floating mandrel and square tube is gradually mature.The banding caused by component segregation is difficult to be eliminated by heat treatment. Generally, normalizing can reduce this segregation to a certain extent. Generally, normalizing can correct the segregation to the allowable level. If the banding is serious, it can be improved by multiple normalizing. It is reliable to conduct high-temperature diffusion annealing first and then normalize again, which can completely eliminate the strip, but the cost will be very high,Fogura40 galvanized square pipe, which is difficult to achieve for the steel plate due to the surface quality.Functional index analysis of qb square tube - mechanical function of plastic square tube. Solid bending, as the name suggests, is to compact the bending. During real bending, the inner and outer rollers and the inner and outer walls of the pipe blank are compacted in both directions.Where to sell API,Special performance steel: A. stainless and acid resistant steel; b. Heat resistant steel: including oxidation resistant steel, heat strength steel and air valve steel; c. Electric heating alloy steel; d. Wear resistant steel; e. Low temperature steel; f. Electrical steel.The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.Fatigue strength plasticity and hardness discussed above are indicators of the mechanical properties of metals under static load. In fact, many machine parts work under cyclic load, under which fatigue will occur.

The square tube is divided into a. boiling steel according to the degree of deoxidation and pouring; b. Semi killed steel; c. Killed steel; d. Special killed steel. The deformation of qb square tube is mainly caused by the shrinkage force of the weld greater than the strength of the base metal.Home page recommendation,Pig iron refers to the product made by smelting iron ore in blast furnace. It is mainly used for steelmaking and square casting. Put the cast pig iron in the melting furnace to obtain cast iron (liquid), and cast the liquid cast iron into a cast square pipe. This kind of cast iron is called cast iron.The square tube adopts the electric contact pressure gauge to press down the pressure of the oil cylinder on both sides of the conveyor to ensure the smooth transportation of the strip steel.Stage ( & mdash; )Fogura,In recent years, large-diameter seamless square tube plays a good role in economic development. Because there are many types of large-diameter seamless square tubes the continuous casting process of large-diameter seamless square tubes is also different. What are the specific steps of the continuous casting process of large-diameter seamless square tube? As the name suggests, square tube is a kind of square tube type. Many materials can form square tube body. Its medium is used for what purpose and where it is used. Most square tubes are steel tubes, which are unpacked, leveled, Then the round pipe is rolled into a square pipe,FoguraRight angle square tube, and then cut into the required length. Generally, square tubes per package are mostly in large specifications in terms of spot, and . - ~~ - square tubes are divided into structural square tubes, decorative square tubes building square tubes, mechanical square tubes, etc. according to their uses.With the progress of the times and the development of science and technology, the application fields of square tubes are widely divided. The main fields are the construction industry. Affected by the environment and weather, square tubes will also rust for a long time. How to improve the rust resistance of square tubes and what are its rust resistance? Let me give you a detailed introduction below.Ferroalloy is an alloy composed of iron and silicon, manganese, chromium, titanium and other elements. Ferroalloy is the raw material for steelmaking. It is used as deoxidizer and alloy element additive for steel in square tube steelmaking.

. fake and inferior square tubes are easy to fold. Folding is a variety of broken lines formed on the surface of square tubes, and this defect often runs through the longitudinal direction of the whole product. The reason for the folding is that the fake and shoddy manufacturers pursue the rate, the reduction is too large, resulting in ears, folding occurs during the next rolling, the folded products will crack after bending, and the strength of the square tube will be greatly reduced.Impact toughness the load acting on the machine part at a great speed by QB is called impact load, and the ability of metal under impact load is called impact toughness.Odiveras,Therefore, QA is usually not preheated. However, when the plate is very thick, it should be preheated because it cools quickly. Once # steel was cracked by J welding. If the plate thickness is more than mm, there is a great risk of not preheating.The disadvantage of empty bending is that during synchronous empty bending at the upper and side, due to the pressure generated by the upper roll and the lower roll at the same time, the forming force is easy to exceed the critical point. All kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have formal qualifications. Welcome to telephone inquiry and sincerely invite cooperation! It will cause edge instability and concave, and will also affect the stable operation of the unit and forming quality. This is also the different characteristics of qb square tube and round tube empty bending.Volksrust,Classification of square tube steel is iron carbon alloy with carbon content of square tube between .% - %. In order to ensure its toughness and plasticity, the carbon content generally does not exceed %. In addition to iron and carbon, the main elements of steel also include silicon, manganese, sulfur, phosphorus, etc. There are various classifications of steel and square tubes, mainly including the following: square tubes are classified into ordinary steel according to quality (P & le; .%, S & le; .%)Square pipe for diamond core drilling (gb-) is a square pipe for drill pipe, core rod and casing for diamond core drilling.Derusting grade for the construction process of epoxy, ethylene, phenolic and other coatings commonly used for square pipes, the surface of square pipes is generally required to reach near white grade (SA). Practice has proved that almost all oxide scale, rust and other dirt can be removed by using this derusting grade, and the depth of anchor grain can reach ~ & mu; m which fully meets the requirements of adhesion between layer and square pipe The shot derusting process can meet the technical conditions of near white level (SA) with low operation cost and stable and reliable quality.

Hardness QB square hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Qb square pipe for mining fluid transportation, Standard No.: gbt-. The representative material is Q grade B steel. It is mainly used for straight seam qb square pipe for mine air pressure, drainage and shaft gas drainage.Engaged in square tube, square rectangular tube, seamless square tube, galvanized tube, old brand, price advantage and quality guarantee! However, the Demander shall cut off the interface pipe when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square pipe with theoretical weight greater than kgm, it shall not exceed % of the total delivery. The bending degree of qb square pipe shall not be greater than mm per meter, and the total bending degree shall not be greater than .% of the total length. Galvanized qb square pipe for low-pressure fluid transmission, with standard number of gbt-. Representative materials: QA, qbqb, etc. It is mainly used for conveying water, gas, air, oil and heating hot water or steam,OdiverasLatest price list of galvanized square pipe, and its purpose is limited to general low pressure fluid.technological innovation,Square pipe for diamond core drilling (gb-) is a square pipe for drill pipe, core rod and casing for diamond core drilling.The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.Square pipe for conveying flammable and non flammable fluids, Standard No.: gbt (gbt - ). The representative material is l-l pipeline steel. It is mainly used to transport flammable and non flammable fluids. Low pressure or high pressure square pipes have high requirements. The purpose of large-diameter qb square pipe is qb square pipe, C-shaped steel and H-shaped steel. It is mainly used in the construction of simple plant, steel structure and other infrastructure. Qb square pipe is generally used as the frame and purlin of the plant. C-shaped steel Steel is an important support for the plant, and H-section steel is used as load-bearing. Especially in recent years, a large number of small and medium-sized enterprises have started to build spacious and bright plants. If traditional buildings are built, the time is slow, the work progress is affected, and the investment is large. For some small and medium-sized enterprises, if the investment in the plant is too high, the capital will be produced after operation Serious impact. The plant built with qb square tube, C-section steel and H-section steel has the characteristics of time saving, money saving and fast use. Therefore, the sales of qb square tube, C-section steel and H-section steel have increased significantly in recent years and become the first choice for plant construction. Qb square tube, C-section steel and H-section steel are mainly used in the construction of simple plant, and the H-shaped steel is used as the load-bearing. Especially in recent years, the time is slow the work progress is affected, and the investment is large. For some small and medium-sized enterprises Said that if the investment in the plant is too high, it will have a serious impact on the capital after operation. The plant built with qb square pipe, C-section steel and H-section steel has the characteristics of time saving money saving and fast use. Therefore, the sales of qb square pipe, C-section steel and H-section steel have increased significantly in recent years, becoming the first choice for plant construction. Large diameter qb square pipe plant is introduced Shao measures for effective wrinkle of seamless square pipe: check the wrinkle state, even when the wrinkle around the part is determined to be less than the clamping force, and the gradual increase of the roll gap force can be. When drawing the cone and hemispherical components, it should be increased to increase the inner diameter of the inner plate and the tensile stress of the wrinkle drawbead. Adopt the principle of loosening after tightening to loosen after tightening and ask Question.

Square pipe is the name of square pipe, that is steel pipe with equal side length. It is made of rolled strip steel after process treatment.How many?, the corner size and edge straightness of square pipe reach or even exceedThe principle of straightening machine is that a disc is divided into two sides to clamp round steel straight lines. Professional square tube and the ability of metal under impact load is called impact toughness.Except for the thickening of wall thickness, square rectangular tube, galvanized square tube, galvanized tube, high price, service, on-site settlement, honest operation! The edge is one with radius r, and the other outer edge must be two equal diameters with radius R. The diameter of the reinforcement to be straightened is D, and the center distance between them is adjusted to R + R + D.Odiveras,It is good to purchase Baosteel's materials for cold drawing of square tubes, because Baosteel's materials are subject to grade flaw detection, so as to improve the yield strength. This process is called cold drawing strengthening. Square tube is generally used for product parts with high requirements. It has good willfulness and strength. The surface is better after cold drawing. Cold drawing principle.Classification of square tube steel is iron carbon alloy with carbon content of square tube between .% - %. In order to ensure its toughness and plasticity it is convenient to line up. The steel is cold drawn at room temperature to produce plastic deformation,OdiverasStandard for galvanized pipe,OdiverasQ345B low alloy square tube, the carbon content generally does not exceed %. In addition to iron and carbon, the main elements of steel also include silicon, manganese, sulfur, phosphorus, etc. There are various classifications of steel and square tubes, mainly including the following: square tubes are classified into ordinary steel according to quality (P & le; .%, S & le; .%)Square pipe welding is suitable for surface treatment of materials. Square pipe welding can be used for ceramic ceramic, metal ceramic and metal metal welding.