Square tube for automobile half shaft sleeve (gb-) is a high-quality carbon structural steel and alloy structural steel hot-rolled square tube for automobile half shaft sleeve and drive axle housing.When the vehicle is replaced with seamless square tube blank, the material is too soft to affect the requirements, so as to ensure the quality of parts and avoid wrinkles.Rilystad,Pile pipe and bridge; Pipes for wharf, road, building structure, etc. It is mainly used as petroleum geological drilling pipe, boiler pipe, bearing pipe, high-precision structural pipe for automobile, tractor and aviation, etc.Product description of square tube square tube is a light thin-walled steel tube with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties, weldability, cold and hot workability and corrosion resistance, and good low temperature toughness.Centurion,Square tube is a very good steel in economic construction. There are many kinds and principles of cold drawing. You may still have a lot of insufficient understanding of the cold drawing principle of each other's pipe. Next, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.When sand blasting or manual mechanical derusting is used, the metal on the surface of the galvanized square pipe is directly exposed in the air. If a primer is not applied in time, the surface of the galvanized square pipe is easy to rust again affecting the adhesion of the paint film. I am engaged in all kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes and other materials all year round. I operate in good faith. Welcome to call! As the paint is a time-effective material, the overstock of inventory is easy to expire. Therefore the main indexes of the paint must be rechecked before use, and the paint can be used only when the results meet the standards.

Hardness hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Elongation after square tube breaking (& sigma;): in the tensile test, the percentage of the length increased by the gauge length of the sample after breaking and the length of the original gauge length is called elongation. In & sigma; Expressed in%.After chemical pickling, the square tube can be well protected by electrolysis. These are simple ways to prolong the service life of the square tube, We only need to treat according to these, so that the square tube can bring us great help in the use process. The cold galvanized square tube is the principle of cold galvanizing on the square tube used to make the square tube have corrosion performance. Different from hot-dip galvanizing, cold galvanizing coating is mainly carried out according to the electrochemical principle. Therefore, it is necessary to ensure the sufficient of zinc powder and steel, resulting in electrode potential difference, so the steel surface treatment requirements are very high.Customer first,RilystadWelded square pipe,RilystadGalvanized square pipe DN150,Square tube production most square tube processing is square tube pressure processing, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, plates and tubes. It is divided into cold rolling and hot rolling.Improve the positioning and pre bending steps, if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.With the progress of the times and the faster and faster economic development, the places where large-diameter seamless square tubes are used are becoming more and more popular

Product description of square tube square tube is a light thin-walled steel tube with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties, weldability, cold and hot workability and corrosion resistance, and good low temperature toughness.Manufacturing cost,Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.(& sigma; Su): the large stress before the yield stress of the sample decreases for the first time; Lower yield point (& sigma; SL): the small stress in the yield stage when the initial instantaneous effect is not considered. The calculation formula of yield point is as follows: where: FS -- yield force (constant) in the tensile process of the sample, n (Newton) so -- original cross-sectional area of the sample mm. Elongation after fracture (& sigma;) in the tensile test, the percentage of the length increased by the gauge length of the sample after breaking to the original gauge length is called elongation.Square tube is made of different materials. It needs qualified inspection by relevant staff before leaving the factory. Square tube has a wide range of uses. Its main field is not only the construction industry, but also can be seen everywhere in our daily life. The service life of square tubes is mainly affected by surface treatment. I will explain the specific operations of surface treatment of square tubes.Rilystad,Square tube is an essential material for the construction and Realization of industrialization. It is widely used and has a wide variety. According to different section shapes, square tube is generally divided into sections, plates, pipes and metal products. In order to facilitate the production, ordering and supply of square tube and do a good job in operation and management, it is also divided into heavy rail, large section steel, medium section steel, small section steel and square tube cold bending Section steel, high-quality section steel, wire rod, medium and thick steel plate, sheet steel, electrical silicon steel sheet strip steel, seamless steel pipe, square pipe, welded steel pipe, metal products, etc.The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.Cold drawn or cold rolled precision square tube (gb-) is a cold drawn or cold rolled precision square tube with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision square mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality.

C. electric furnace steel: (a) electric arc furnace steel; (b) Electroslag furnace steel; (c) Induction furnace steel; (d) Vacuum consumable furnace steel; (e) Electron beam furnace steel.Use classification square tubes are divided into: square tubes for decoration,TetovoHow much is sc80 galvanized steel pipe per meter, square tubes for machine tool equipment, square tubes for mechanical industry, square tubes for chemical industry, square tubes for steel structure, square tubes for shipbuilding, square tubes for automobile, square tubes for steel beams and columns, and square tubes for special purposes.Functional index analysis of qb square tube - commonly used are Brinell angle (HB), Rockwell angle (HRC) and Vickers angle (HV) of qb square tube. Angle is a gauge needle to weigh the soft and hard level of metal data. The angle method is rarely used to determine the internal angle in the current life. It uses the metal data surface tested under the fixed load of the indenter with a certain number and shape to determine its angle value according to the level of the object.Safety production,Generally, chemical and electrolytic pickling are used for pickling treatment. Only chemical pickling is used for pipelines, which can remove oxide scale, rust and old coatings. Professional square tubes, rectangular tubes, seamless square tubes galvanized square tubes and galvanized tubes are safe, environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted. Sometimes they can be used as reprocessing after sand blasting and rust removal. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the environment.The surface of galvanized square pipe treated by sand blasting, shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.Square pipe for diamond core drilling (gb-) is a square pipe for drill pipe, core rod and casing for diamond core drilling.

Generally,TetovoDN32 galvanized square pipe, chemical and electrolytic pickling are used for pickling treatment. Only chemical pickling is used for pipelines, which can remove oxide scale, rust and old coatings. Professional square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes are safe, environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted. Sometimes they can be used as reprocessing after sand blasting and rust removal. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the environment.Standard requirements,Pull square tube:It is forbidden to degrease the oil square pipes and pipe fittings in the direct production concentration unit, air separation unit, oil refining and chemical engineering according to the design requirements. The purpose of degreasing is to prevent the transported or stored materials from being contaminated by grease or organic matter; Avoid mixing transported or stored materials with grease or organic matter; Oil content to ensure the activity of the catalyst; The content of oil and organic matter to ensure the purity of the product. The installed square pipe shall be disassembled into pipe sections for degreasing. Pipes that cannot be disassembled after installation shall be degreased before installation. Square pipes with obvious oil stains or serious corrosion shall be cleaned by steam purging, sand blasting or other methods before degreasing.Stage ( & mdash; )Tetovo,Derusting: This is an important process for galvanized square pipes and components before coating, and it is the key to the quality of galvanized square pipes. Thorough derusting can improve the adhesion of antirust paint and prolong the service life of galvanized square pipe.Impact toughness the load acting on the machine part at a great speed by QB is called impact load and the ability of metal under impact load is called impact toughness.Square tube has a wide range of application fields. Its main field is the construction industry,TetovoHow much is 80 galvanized pipe per meter, which promotes the development of economic construction. Because the production process of square tube hole is different, the production design of square tube hole is also different. Next, I will introduce in detail the types of tube hole design below.

Generally, chemical and electrolytic pickling are used for pickling treatment. Only chemical pickling is used for pipelines, which can remove oxide scale, rust and old coatings. Professional square tubes, rectangular tubes, seamless square tubes galvanized square tubes and galvanized tubes are safe,Electrochemical polishing: long specular gloss its anchor lines are shallow and easy to pollute the environment.Superior square tubular steel (both P and s ≤ .%)Zandan environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted. Sometimes they can be used as reprocessing after sand blasting and rust removal. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, stable process, less pollution and good durability. Suitable for mass production, it is mainly applied to high-grade products, imported products and public service products. Its processing technology is stable and the operation is simple.Pig iron refers to the product made by smelting iron ore in blast furnace. It is mainly used for steelmaking and square casting. Put the cast pig iron in the melting furnace to obtain cast iron (liquid), and cast the liquid cast iron into a cast square pipe. This kind of cast iron is called cast iron.Paraiso,Due to the increase of square tube production, there are more and more fake and shoddy square tubes in the market. How to distinguish the fake and shoddy square tubes? Let me teach you some points to distinguish the fake and shoddy square tubes.. fake and inferior square tubes are easy to fold. Folding is a variety of broken lines formed on the surface of square tubes, and this defect often runs through the longitudinal direction of the whole product. The reason for the folding is that the fake and shoddy manufacturers pursue the rate, the reduction is too large, resulting in ears, folding occurs during the next rolling, the folded products will crack after bending, and the strength of the square tube will be greatly reduced.We all know very well. Therefore, the quality of square tubes will directly affect the development of the construction industry. What if we can make the service life of square tubes longer? Here, we also need to ask the personnel of the square tube manufacturer for instructions, and use ingenious methods to prolong the service life of the square tube, so that the square tube can bring us greater help in life.

A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.General square pipes are stacked outdoors, and most of them are buried underground when in use, so they are easy to corrode and rust. In order to ensure the smooth flow of the pipeline, square pipes must have strong corrosion resistance. Once the pipeline is corroded,ZandanHow much is 50 galvanized square tube per meter, it will cause oil and gas leakage, which will not only interrupt transportation, but also pollute the environment,ZandanCold galvanized square pipe factory, and may even lead to fire and cause harm.Tool derusting mainly uses tools such as steel wire brush to polish the surface of square pipe, which can remove loose or oxidized scale, rust, welding slag, etc. The derusting of manual tools can reach grade SA and that of power tools can reach grade SA. If the square pipe surface is firmly attached with iron oxide scale, the derusting effect of tools is not ideal and can not reach the anchor depth required by construction.agent,High quality steel (P & le; .%, S & le; .%)Steel pipe for geological drilling (yb-) is a steel pipe used by geological departments for core drilling. It can be divided into drill pipe, drill collar, core pipe, casing, sedimentation pipe etc.When sand blasting or manual mechanical derusting is used, due to the falling off of the oxide scale of the galvanized square pipe, the metal on the surface of the galvanized square pipe is directly exposed in the air. If a primer is not applied in time, affecting the adhesion of the paint film. I am engaged in all kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes and other materials all year round. I operate in good faith. Welcome to call! As the paint is a time-effective material, the overstock of inventory is easy to expire. Therefore,ZandanDN150 galvanized square pipe, the main indexes of the paint must be rechecked before use, and the paint can be used only when the results meet the standards.

Square tube is a very good steel in economic construction. There are many kinds and principles of cold drawing. You may still have a lot of insufficient understanding of the cold drawing principle of each other's pipe. Next, I'll lead you to learn its cold drawing principle.Bidding,Square tube structural steel A. mechanical steel: (a) quenched and tempered structural steel; (b) Surface hardening structural steel: including carburized steel, ammoniated steel and surface quenching steel; (c) Easy to cut structural steel; (d) Steel for cold plastic forming: including steel for cold stamping and steel for cold heading.Formulate the documents stored by the square tube for a long time and implement them in accordance with.We all know very well. Therefore, we also need to ask the personnel of the square tube manufacturer for instructions, and use ingenious methods to prolong the service life of the square tube, so that the square tube can bring us greater help in life.Zandan,Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner, resulting in an under current area. The zinc layer at this part is thin, and there is no zinc layer attached to the cold galvanized square pipe. The cold galvanized square pipe has no zinc lump and caking as a whole, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer, and there will be water marks and a few zinc tumors, but the overall zinc layer is thick, rectangular tube and complex section square tube & mdash& mdash; Surface treatment classification of flower shaped square pipe, open square pipe, corrugated square pipe and special-shaped square pipe square pipe is divided into hot-dip galvanized square pipe electro galvanized square pipe, oil coated square pipe and pickling square pipe according to surface treatment. Square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machinery industry, chemical industry, steel structure, shipbuilding, automobile, steel beam and column and special purpose are classified by wall thickness & mdash& mdash; Super square tube, square tube and thin-walled square tube plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.For oil, the oil brush work shall be carried out in accordance with the requirements of the rule system, so as to ensure the oil brush and the oil in the correct position of the brush and avoid wrinkles.

There are many ways of ignition, electric spark, flame, strong current, high-temperature furnace, electron beam, laser, high-temperature radiation, microwave, chemical furnace, etc.With the improvement of production quality, the quality of square tubes is getting better and better. The quality of square tubes will affect our lives. Because the functions of square tubes are different, their characteristics and uses are different. I will introduce the characteristics and uses of square tubes in detail.Haoda,The advantages of real bending are small reverse, and as long as the roll shape is accurate, the R of inner corner forming is more accurate.The square tube is divided into a. boiling steel according to the degree of deoxidation and pouring; b. Semi killed steel; c. Killed steel; d. Special killed steel. The deformation of qb square tube is mainly caused by the shrinkage force of the weld greater than the strength of the base metal.Gurlan,The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.Stainless steel square tube for fluid transportation (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square tube made of stainless steel for fluid transportation.The second is to clean the surface of the opposite pipe. When cleaning the opposite pipe, the surface should be cleaned with solvent or emulsion. Square pipes of various specifications, square rectangular pipes, seamless square pipes, galvanized square pipes, galvanized pipes are supplied in time and cost-effective. They have become the preferred brand of many wire products. Welcome to buy! It is used to remove oil and dust. It is only suitable for removing grease and dust on the surface of square pipe, which can not remove rust and oxide scale. Therefore, it can only be used as an auxiliary means in production.

Hot dip galvanized square pipe is widely used, mainly in curtain wall,HaodaGalvanized square pipe machine, solar power generation support, construction, machinery and steel structure engineering, especially in curtain wall, Standard No.: gbt-. Representative material: qab grade. It is mainly used to transport low-pressure fluids such as water, gas, air and heating steam.Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression,HaodaWhat are the specifications of galvanized round pipe, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid, salt,HaodaGalvanized square pipe production line, rail, steel plate, large-diameter steel pipe, forging, etc. can be stacked in the open air; Small and medium-sized section steel, wire rod reinforcement, steel wire and steel wire rope can be stored in a well ventilated shed medium diameter steel pipe, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets, or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, and generally adopts ordinary closed warehouse, that is, the warehouse with roof, enclosure, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, loading and unloading and shall not be damaged, The storage period of materials can be extended, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel, alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, it can reflect that the square tube is good. On the contrary, if the surface is not goodQuality assurance,Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner, resulting in an under current area. The zinc layer at this part is thin, and there is no zinc layer attached to the cold galvanized square pipe. The cold galvanized square pipe has no zinc lump and caking as a whole, but the overall zinc layer is thin, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer, and there will be water marks and a few zinc tumors, but the overall zinc layer is thick, and the thickness of the zinc layer on the inner and outer walls of the square tube is -mu; M above. The nature of QB square tube!For oil, the oil brush work shall be carried out in accordance with the requirements of the rule system, so as to ensure the oil brush and the oil in the correct position of the brush and avoid wrinkles.High quality steel (P & le; .%, S & le; .%)

Hardness hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Quality inspection report, seamless square tube square rectangular tube, galvanized square tube, galvanized tube, old brand, price advantage and quality guarantee! However, the Demander shall cut off the interface pipe when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square pipe with theoretical weight greater than kgm, it shall not exceed % of the total delivery. The bending degree of qb square pipe shall not be greater than mm per meter, and the total bending degree shall not be greater than .% of the total length. Galvanized qb square pipe for low-pressure fluid transmission, with standard number of gbt-. Representative materials: QA, qbqb, etc. It is mainly used for conveying water, gas, air, oil and heating hot water or steam, and its purpose is limited to general low pressure fluid.Formulate the documents stored by the square tube for a long time and implement them in accordance with.Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.Haoda,The load of impact toughness acting on the parts at a great speed is called impact load. It is specialized in products and renewable resources. Its business includes: square tube, square tube, seamless square tube, galvanized square tube and galvanized tube. The ability of metal under impact load is called impact toughness.Precision inner diameter square tubes for hydraulic and pneumatic cylinders (gb-) are cold drawn or cold-rolled precision square tubes with precision inner diameter for hydraulic and pneumatic cylinders.Generally speaking, square pipe welding has a process: ignition, pressurization and thermal insulation.

, cold drawn tubes, tubes, etc. Hot rolled seamless tubes are produced on the automatic precision tube precision tube rolling mill. The solid tube blank is cut into the required length by removing surface defects, centering on the end face of the perforated end of the tube blank, and then sent to the heating furnace for heating. It is perforated on the piercing machine. At the same time, and then sent to the automatic pipe mill for continuous rolling. After the wall thickness is adjusted by the whole machine which is called the rough pipe A cavity is gradually formed inside the pipe blank, and the diameter is determined by the sizing machine to meet the specification requirements. The continuous pipe mill is more advanced in producing hot-rolled seamless steel pipe. If you want to obtain seamless pipe with smaller size and better quality, Cold rolling and cold drawing must be adopted, or the combination of cold rolling and cold drawing is usually carried out on the roll mill. The seamless pipe is rolled in the annular pass composed of variable section circular hole groove and fixed conical plug. Cold drawing is usually carried out on the single chain or double chain cold drawing machine, that is,AlmeroHow much is 80 galvanized square tube, the heated pipe blank is placed in a closed cylinder, and the perforated rod and rod move, This method can produce steel pipe with small diameter. In the building materials industry, the development of various pipes is different. Because of their different characteristics, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. We need to understand the various characteristics of steel pipes. However, in the building materials industry, the development of various pipes is different. Because of their different characteristics, there is a certain distance between pipes. Square pipe is one of many pipes in the building materials industry. It is formed after strip steel treatment. The various characteristics of steel pipe need to be understood by everyone. However, due to the of steel pipe and other raw materials, the storage of steel pipe needs specific conditions.Due to the increase of square tube production, there are more and more fake and shoddy square tubes in the market. How to distinguish the fake and shoddy square tubes? Let me teach you some points to distinguish the fake and shoddy square tubes.Almero,The square tube will be tested in many aspects of its performance in the process. Each test is for the square tube to have a good performance in practical application. So what are the different properties of square tubes? Next, I'll introduce the characteristics of the lower tubes in terms of mechanical properties.Fatigue strength, plasticity and hardness discussed above are indicators of the mechanical properties of metals under static load. In fact, under which fatigue will occur.Matsuyama,Structural stainless steel square pipe (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square pipe made of stainless steel for corrosion-resistant pipes, structural parts and parts widely used in chemical, petroleum, light textile, machinery and other industries.There are sets of MPM and sets of MRK pipe mills in the world. Strength refers to the function of qb square tube data being destroyed under static load (appropriate plastic deformation or fracture). Because the action forms of load include tension, contraction,AlmeroQ345D square tube, meandering, shear and so on, because the strength is also divided into tensile strength, compressive strength, flexural strength, shear strength and so on. There is often a definite connection between various strengths. Long term square tube square rectangular tube, seamless square tube, and the price is % higher than the market price! The price of more than one ton is higher! In normal use, tensile strength is often taken as the fundamental strength gauge needle.Generally, chemical and electrolytic methods are used

Impact toughness the load acting on the machine part at a great speed by QB is called impact load, and the ability of metal under impact load is called impact toughness.After the process of polishing the surface effect of the square tube is quite good. The quality of the polishing process directly affects the external image of the square tube. Therefore, we must choose the appropriate polishing according to the above, and pay more attention to the polishing process of the square tube.Alloy steel: A. low alloy steel (total alloy element content & le; %); b. Medium alloy steel (total alloy element content > ~ %); c. High alloy steel (total alloy element content > %).Free consultation,Comprehensive classification ordinary steel A. carbon structural steel: (a) Q (b) Q (b); (c) Q( C)； (d) Q( B)； (e) Q.Empty bending empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected,AlmeroDN20 hot dip galvanized pipe, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.

The local heat release in the welding process of square tube can reduce the heat affected zone, avoid the micro of thermal sensitive materials, and maintain the properties of materials.Range,According to smelting classification and furnace type, A. open hearth steel: (a) acid open hearth steel; (b) Alkaline open hearth steel.Performance index analysis of square tube - impact toughness the load acting on the part at a great speed is called impact load, and the ability of metal under impact load is called impact toughness.According to smelting classification and furnace type, A. open hearth steel: (a) acid open hearth steel; (b) Alkaline open hearth steel.Almero,B. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. Seamless pipe can be divided into hot rolled pipe and cold rolled pipe according to different productionB. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.

Ship carbon steel square pipe (gb-) is a carbon steel square pipe for ship class I pressure pipe system, class II pressure pipe system, boiler and superheater. It is a long-term business square pipe, square pipe, seamless square pipe, galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃, and the working temperature of alloy steel square pipe wall shall exceed ℃.Stage ( & mdash; )Pelepe,Square tubes can be degreased with organic solvents (vinyl chloride, vinyl chloride, carbon chloride, industrial solvents, benzene,PelepeGalvanized square pipe 100, acetone, etc.), concentrated or alkaline solution. Industrial vinyl chloride is suitable for degreasing metal parts; Industrial chlorinated carbon is suitable for degreasing ferrous metal and non-metallic parts; Vinyl chloride is suitable for degreasing metal parts and non-ferrous metal parts; The industrial concentration shall not be less than %, which is suitable for manual scrubbing of the inner surface of the container with low degreasing requirements; % concentrated, suitable for degreasing some pipe fittings and porcelain rings of concentrated device.In this period, the technology of continuous rolling pipe was not mature.Atakpame,With the progress of the times and the faster and faster economic development, the places where large-diameter seamless square tubes are used are becoming more and more popularImprove the positioning and pre bending steps if necessary, to ensure that the web hunting problem does not occur when pressing parts. Change the shape of the surface pressure of the material to ensure the quality of the parts and avoid the non movement of the surface shape of the roll gap, resulting in uneven walking feeding.Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.

The difference between square pipe and seamless steel pipe the main feature of seamless steel pipe is no welding joint and can withstand large pressure. The product can be very rough as cast or cold drawn parts.Now stainless steel is gradually replacing pure iron products in our life, and now the steel pipe is also gradually innovated. Now the qb square pipe is a typical representative. However, the above small series are not the focus. Today, the focus is on the analytical process of qb square tube sizing rolling.Square tube is an essential material for the construction and Realization of industrialization. It is widely used and has a wide variety. According to different section shapes, square tube is generally divided into sections, plates, pipes and metal products. In order to facilitate the production,PelepeQ235 galvanized rectangular pipe, ordering and supply of square tube and do a good job in operation and management, it is also divided into heavy rail, light rail, large section steel, small section steel and square tube cold bending Section steel, high-quality section steel, medium and thick steel plate, sheet steel, electrical silicon steel sheet, strip steel, seamless steel pipe, welded steel pipe, etc.new productThe disadvantage of empty bending is that during synchronous empty bending at the upper and side, due to the pressure generated by the upper roll and the lower roll at the same time, the forming force is easy to exceed the critical point. All kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have formal qualifications. Welcome to telephone inquiry and sincerely invite cooperation! It will cause edge instability and concave, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.Engaged in square tube, square rectangular tube, seamless square tube, galvanized square tube, galvanized tube, old brand, price advantage and quality guarantee! However, the Demander shall cut off the interface pipe when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square pipe with theoretical weight greater than kgm it shall not exceed % of the total delivery. The bending degree of qb square pipe shall not be greater than mm per meter, qbqb with standard number of gbt-. Representative materials: QA, etc. It is mainly used for conveying water, gas, air, oil and heating hot water or steam, and its purpose is limited to general low pressure fluid.

Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, so that the steel sand, steel shot, iron wire section, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force, which can not only completely remove rust oxides and dirt, but also the square tube under the violent impact and force of abrasives, It can also achieve the required uniform roughness.Management Department,Square tube plays an important role in the rapid economic development. The functions of square tube are different, and its characteristics are also different. Square tube has strict standards. There are many welding processes and advantages of square tube. Let me show you the welding process and advantages of lower tube.After isothermal quenching, qqb square tube will have excellent rolling fatigue characteristics and corrosion resistance. Wear resistance, fracture toughness, impact toughness and bending strength. Therefore, in the subsequent production and application, qqb square tube will be used as the material of rolling mill flap ball screw. The qqb square tube of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment, and its application range is expected to be improved and expanded.The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.Pelepe,The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.Large diameter qb square tube production standard classification square tube is divided according to production standard: national standard square tube, Japanese standard square tube, British standard square tube, American standard square tube, European standard square tube and non-standard square tube.Fake and shoddy square tubes are easy to scratch, because the equipment of fake and shoddy material manufacturers is simple and easy to produce burrs and scratch the surface of square tubes. Deep scratches reduce the strength of square tubes.

Welding is a synthetic gradient material, which can be used as solder to weld special-shaped materials in order to overcome the mismatch of chemical, mechanical and physical properties between base metals.The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.Kumanovo,The quality of the solid square tube after the square tube formwork removal and curing can be tested according to the requirements and the following ways: use a magnifying glass to observe whether there are non external force cracks on the structural surface of the solid seamless qb square tube. When non external force cracks appear on the surface of qb square pipe, the crack width on the structural surface of ordinary qb square pipe shall not be greater than .mm.Section shape classification of large-diameter qb square tube square tube is classified according to section shape: simple section square tube & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Flower shaped square pipe, open square pipe, corrugated square pipe, special-shaped square pipe, large-diameter qb square pipe surface treatment classification square pipe is divided according to surface treatment: hot-dip galvanized square pipe, electro galvanized square pipe, oil coated square pipe, acid pickling square pipe, large-diameter qb square pipe purpose classification square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machinery industry, chemical industry, steel structure, shipbuilding, automobile, special purpose, large-diameter qb square tube wall thickness classification, large-diameter qb square tube according to wall thickness Classification & mdash& mdash; Super large diameter qb square pipe, large diameter qb square pipe and thin-wall large diameter qb square pipe rectangular pipe are the names of square pipe and QB square pipe that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment. Generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Usually pieces per bag. Qb square pipe, also known as square and rectangular cold-formed hollow section steel, is referred to as square pipe and rectangular pipe, code f and j respectively. The allowable deviation of wall thickness of qb square pipe shall not exceed plus or minus % of nominal wall thickness when the wall thickness is not greater than mm, plus or minus % of wall thickness when the wall thickness is greater than mm, except for the wall thickness of corner and welding joint area.Azor,Pig iron refers to the product made by smelting iron ore in blast furnace. It is mainly used for steelmaking and square casting. Put the cast pig iron in the melting furnace to obtain cast iron (liquid), and cast the liquid cast iron into a cast square pipe. This kind of cast iron is called cast iron.Change to square pipe: generally,Kumanovo100 galvanized square pipe, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.

Viewing color: the color of the cold galvanized square tube is yellowish green, cyan white or slightly colored at a fixed angle with the sun. The color of hot-dip galvanized square pipe is silver white at a fixed angle with the sun.D. do not cut your hands boring, especially for girls. Holding or fingers will bind themselves.Special performance steel: A. stainless and acid resistant steel; b. Heat resistant steel: including oxidation resistant steel heat strength steel and air valve steel; c. Electric heating alloy steel; d. Wear resistant steel; e. Low temperature steel; f. Electrical steel.Let's see,Kumanovo76 galvanized square pipe, special shaped square pipe is the general name of square pipes with other cross-section shapes except circular pipe. According to the different cross-section shape and size of steel pipe, it can be divided into special-shaped square pipe with equal wall thickness (code D), tools and mechanical parts. Compared with circular tubes, special-shaped tubes generally have large moment of inertia and section modulus, and have large bending and torsion resistance, which can greatly reduce the structural weight and save steel. Square tubes are an indispensable part of construction workSquare tube for automobile half shaft sleeve (gb-) is a high-quality carbon structural steel and alloy structural steel hot-rolled square tube for automobile half shaft sleeve and drive axle housing.Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.

Steel used & mdash& mdash; Such as bridge steel, ship steel, boiler steel, pressure vessel steel, agricultural machinery steel, etc.Quality department,For transportation: water supply, drainage, sewage treatment engineering,Kumanovo50 price of galvanized square pipe, mud transportation, the surface treatment before coating is also called coating surface pretreatment.The technology of floating mandrel and square tube is gradually mature.Kumanovo,The principle of straightening machine is that a disc is divided into two sides to clamp round steel straight lines. Professional square tube, square rectangular tube seamless square tube, galvanized square tube, galvanized tube, high price, service, on-site settlement, honest operation! The edge is one with radius r, and the other outer edge must be two equal diameters with radius R. The diameter of the reinforcement to be straightened is D, and the center distance between them is adjusted to R + R + D.Viewing color: the color of the cold galvanized square tube is yellowish green, square rectangular tube, seamless square tube, galvanized square tube, galvanized tube, old brand, price advantage and quality guarantee! However, the Demander shall cut off the interface pipe when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square pipe with theoretical weight greater than kgm, it shall not exceed % of the total delivery. The bending degree of qb square pipe shall not be greater than mm per meter, and the total bending degree shall not be greater than .% of the total length. Galvanized qb square pipe for low-pressure fluid transmission, with standard number of gbt-. Representative materials: QA qbqb, gas etc. It is mainly used for conveying water, air, oil and heating hot water or steam, and its purpose is limited to general low pressure fluid.

With the progress of the times and the faster and faster economic development, the places where large-diameter seamless square tubes are used are becoming more and more popularStage ( & mdash; )Bitola,The quality of the solid square tube after the square tube formwork removal and curing can be tested according to the requirements and the following ways: use a magnifying glass to observe whether there are non external force cracks on the structural surface of the solid seamless qb square tube. When non external force cracks appear on the surface of qb square pipe, the crack width on the structural surface of ordinary qb square pipe shall not be greater than .mm.Square tubes for petroleum cracking (gb-) are furnace tubes, heat exchangers and pipeline square tubes suitable for petroleum refineries.Katamaka,The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.QB square tube is a product appeared in recent years, which mainly has strict tolerance and roughness for the dimensions of inner hole and outer wall. Production process classification of large-diameter qb square tube large-diameter qb square tube is divided into hot-rolled seamless square tube, cold drawn seamless square tube, seamless square tube and qb square tube according to production process. Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Material classification of straight seam welded square pipe and spiral welded square pipe large diameter qb square pipe: plain carbon steel square pipe and low alloy square pipe. Ordinary carbon steel is divided into Q Q q SS, # steel, etc; Low alloy steels are divided into q Mn Q, St-, etc.The first is to remove the rust of the square tube. When removing the rust of the square tube, the steel wire brush is mainly used to polish its surface, which can effectively remove the loose or rusty rust on the surface of the square tube.

In recent years, large-diameter seamless square tube plays a good role in economic development. Because there are many types of large-diameter seamless square tubes, the continuous casting process of large-diameter seamless square tubes is also different. What are the specific steps of the continuous casting process of large-diameter seamless square tube? As the name suggests, square tube is a kind of square tube type. Many materials can form square tube body. Its medium is used for what purpose and where it is used. Most square tubes are steel tubes, which are unpacked,BitolaNational standard galvanized square pipe, leveled crimped and welded to form round tubes, Then the round pipe is rolled into a square pipe, and then cut into the required length. Generally, square tubes per package are mostly in large specifications in terms of spot, and . - ~~ - square tubes are divided into structural square tubes, decorative square tubes, building square tubes, mechanical square tubes, etc. according to their uses.The square tube can be sprayed with fluorocarbon paint, which needs some treatment before spraying.B. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.query,BitolaGalvanized square pipe quick connector,The surface of fake and inferior square tubes is easy to produce scabs. There are two reasons: the material of fake and inferior square tubes is uneven and there are many impurities. The guide equipment of fake and shoddy material manufacturers is simple and easy to stick to steel. These impurities are easy to scar after biting the roll.It should be noted that the position of the disc from the calibration line can be adjusted according to the reinforcement diameter, and R and R can be equal or different.Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).

High quality steel (P & le; .%, S & le; .%)Development Curriculum,The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.Function index analysis of square tube - strength and plasticity discussed later are machine function indicators of metal under static load. In practice, many mechanical machines are under repeated load employment. In this environment, the whole opportunity is tired.The reason why the surface of fake and shoddy materials is easy to crack is that its blank is adobe with many air holes. During the cooling process, and there are cracks after rolling.Bitola,Hardness QB square hardness is a pointer to measure the hardness and softness of metal materials. At present, chemical and electrolytic methods are usedSection shape classification square tubes are classified according to section shape: simple section square tubes & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Surface treatment classification of flower shaped square pipe, open square pipe, corrugated square pipe and special-shaped square pipe square pipe is divided into hot-dip galvanized square pipe, electro galvanized square pipe,BitolaGalvanized pipe fittings, oil coated square pipe and pickling square pipe according to surface treatment. Square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machine tools and equipment, machinery industry, steel structure, shipbuilding, automobile, steel beam and column and special purpose are classified by wall thickness & mdash& mdash; Super square tube, square tube and thin-walled square tube plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.

For improper stamping direction, simulation software shall be used in the initial stage of design to ensure that the direction of stamping parts is analyzed, and when the high-quality requirements of components require the re development of molds, the direction shall be adjusted to seamless square tubes. The square tube manufacturer introduces the forming, the bending is compacted, and the inner and outer rollers are double with the inner and outer walls of tube billets during actual bending Compact towards the.Pull square tube:Skopje,In the standard of qb square tube, most of them specify tensile test and hardness test at the same time. For those materials that are not convenient for hardness test, such as qb square tube, only tensile test is specified. In particular, the new portable surface Rockwell hardness tester and pipe Rockwell hardness tester can quickly and accurately test the hardness of stainless steel plate, stainless steel strip and qb square tube as thin as .mm which makes it easy to solve the problems that were difficult to solve in China in the past.Due to the increase of square tube production, there are more and more fake and shoddy square tubes in the market. How to distinguish the fake and shoddy square tubes? Let me teach you some points to distinguish the fake and shoddy square tubes.Zory,Functional index analysis of qb square tube - commonly used are Brinell angle (HB), Rockwell angle (HRC) and Vickers angle (HV) of qb square tube. Angle is a gauge needle to weigh the soft and hard level of metal data. The angle method is rarely used to determine the internal angle in the current life. It uses the metal data surface tested under the fixed load of the indenter with a certain number and shape to determine its angle value according to the level of the object.There are many ways of ignition, such as arc, electric spark, flame, strong current, high-temperature furnace, electron beam, laser, high-temperature radiation, microwave, chemical furnace, etc.Square tubes have different functions and different characteristics. Square tubes of various specifications, square rectangular tubes, seamless square tubes galvanized square tubes and galvanized tubes are welcome to waste merchants, industries, enterprises and power departments to visit and negotiate! Oxidation will also occur on the surface of square tubes after long-term use. What should we do if oxidation occurs? Let me give you a detailed introduction on how to remove square tubes Oxide scale.

Square tube, modified square tube square tube, QB square tube and hot-rolled square tube are qualified in quality inspection. The manufacturer adopts advanced equipment to ensure the quality of each product. Magnetic flux leakage testing for surface defects of square tubes is very similar to magnetic particle testing for square tubes, sensitivity and reliability are stronger than magnetic particle testing. Indirect square forming process the traditional forming process of cold-formed square pipe is to gradually roll the hot-rolled steel coil multi stand forming unit into round pipe at room temperature, and then the shaping unit will roll the round pipe into square pipe, which is called indirect square forming process. The traditional roll forming process uses the method of fixed bending point position and variable bending radian to complete the corner forming of pipe blank, which is suitable for rolling small and medium-sized products. Rolling with this process & ldquo; Superb & rdquo; Square tube will show its inherent defects. Because the roll work in the bending process of this process is always concentrated at the point, excessive stress concentration often shows microcracks in the bending process of profiles, which will lead to cracking in serious cases. The products with such defects have serious consequences when they are used in building steel structures. The study of the broken square tube column in the Hanshin earthquake in Japan shows that the corner microcrack is the main cause of the square tube fracture. At the same time, due to the different forming bending radians of products with different wall thickness, the universality of rolls is limited. The large-size cold-formed square tube used in the process adopts the advanced & ldquo; Direct Square & rdquo; The production process is to directly roll the hot-rolled steel coil into a square and rectangular shape at room temperature.After the square pipe is produced, the surface treatment is generally carried out, that is, the scale, rust, the service life of the saw blade. Regrinding times of the saw blade. When the saw blade is replaced, the main drive AC motor spindle rotates stepless speed change AC motor feed capacity stepless speed change feed fast return to a constant value center system brush device hydraulic saw cutting system system system represents the quality RA flatness, large burr height cutting Chip length tolerance dimension: width and length . ~ .mm ~ m ~ ~ min kW ~ rpm ( kw ~ mmmin mmmin .kw .kw & times; kW S & mu; m . mm & plusmn; mm about mm about mm about mm high. The total weight of each billet square tube is seconds (including, pipe blank cutting, opening device, pipe blank discharge, head and tail cutting time, but excluding pipe blank transportation time). The large production capacity of the three saws is T / A. the pipe blank saw has a special reversing device (hydraulic servo device) to reduce vibration and improve the service life of the saw (only during feeding). The sawing machine has two devices distributed at the inlet and outlet (the input area is supported by roller table to ensure the bending of billet) The inlet end after sawing. Open it to ensure that the saw blade does not contact the blank when it returns. & mdash; feed saw gear & mdash; saw gear vibration reduction, which is composed of a fixed gear vibration reduction, as a movable vibration reduction to avoid the axial of the saw blade. & mdash; brush and sweep device & mdash; a driving brush and sweep device is installed at the bottom of the saw blade to clean the iron filings on the teeth and will not affect the service life of the saw blade. &Mdash; saw blade. In order to improve the service life of the saw blade, a small amount of high load agent container is atomized by air and poured on the saw blade without residue. & mdash; saw blade cooling device. A special nozzle is used to spray cold air at - oC on the saw blade. The cut-off blank is transferred to the buffer chain in front of the loader after passing through the outlet roller table and weighing device (Note: # before sawing, there is a feeding bench for single size billets that need to be cut, and after weighing, there is a feeding bench for returned billets). The buffer transfer chain transports the billets to the lower roller table of the loader. The billets are turned over from the chain to the roller table by the turnover hook. The weighed qualified billets are loaded into the annular furnace by the loader, and the weighed unqualified billets are transported from the roller table to the removal bench for removal.Installation works,SkopjeGalvanized square pipe factory,Alloy steel: A. low alloy steel (total alloy element content & le; %); b. Medium alloy steel (total alloy element content > ~ %); c. High alloy steel (total alloy element content > %).Empty bending empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner, resulting in an under current area. The zinc layer at this part is thin, and there is no zinc layer attached to the cold galvanized square pipe. The cold galvanized square pipe has no zinc lump and caking as a whole, but the overall zinc layer is thin, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer, and there will be water marks and a few zinc tumors, but the overall zinc layer is thick, and the thickness of the zinc layer on the inner and outer walls of the square tube is -mu; M above. The nature of QB square tube!

: it refers to the processing of square tube, which places metal in a closed Jane and applies pressure at the end to extrude the metal from the specified die hole to obtain finished products with the same shape and size. It is mostly used to produce non-ferrous metal materials. Square tube ferrous metal, steel and non-ferrous metal. Before introducing the classification of steel, briefly introduce the basic concepts of ferrous metal, square tube steel and non-ferrous metal.Safety and health,When sand blasting or manual mechanical derusting is used, due to the falling off of the oxide scale of the galvanized square pipe, the metal on the surface of the galvanized square pipe is directly exposed in the air. If a primer is not applied in time, the surface of the galvanized square pipe is easy to rust again, affecting the adhesion of the paint film. I am engaged in all kinds of square tubes, square rectangular tubes seamless square tubes, galvanized square tubes,Skopje65 galvanized pipe, galvanized tubes and other materials all year round. I operate in good faith. Welcome to call! As the paint is a time-effective material the overstock of inventory is easy to expire. Therefore, the main indexes of the paint must be rechecked before use, and the paint can be used only when the results meet the standards.After RH treatment, the molten steel should be fed with Si Ca line when the molten steel temperature is high. At this time, calcium treatment can reduce sulfur segregation in the later solidification process.Square tube heating process square tube calculates the chip thickness of workpiece. After each regrinding, the service life of the saw blade. Regrinding times of the saw blade. When the saw blade is replaced, the main drive AC motor spindle rotates stepless speed change AC motor feed capacity stepless speed change feed fast return to a constant value center system brush device hydraulic saw cutting system system system represents the quality RA flatness, large burr height cutting Chip length tolerance dimension: width and length . ~ .mm ~ m ~ ~ min kW ~ rpm ( kw ~ mmmin mmmin .kw .kw & times; kW S & mu; m . mm & plusmn; mm about mm about mm about mm high. The total weight of each billet square tube is seconds (including, pipe blank cutting, saw blade return, opening device, pipe blank discharge, head and tail cutting time, which is composed of a fixed gear vibration reduction, as a movable vibration reduction to avoid the axial of the saw blade. & mdash; brush and sweep device & mdash; a driving brush and sweep device is installed at the bottom of the saw blade to clean the iron filings on the teeth and will not affect the service life of the saw blade. &Mdash; saw blade. In order to improve the service life of the saw blade, a small amount of high load agent container is atomized by air and poured on the saw blade without residue. & mdash; saw blade cooling device. A special nozzle is used to spray cold air at - oC on the saw blade. The cut-off blank is transferred to the buffer chain in front of the loader after passing through the outlet roller table and weighing device (Note: # before sawing, and after weighing, there is a feeding bench for returned billets). The buffer transfer chain transports the billets to the lower roller table of the loader. The billets are turned over from the chain to the roller table by the turnover hook. The weighed qualified billets are loaded into the annular furnace by the loader, and the weighed unqualified billets are transported from the roller table to the removal bench for removal.Skopje,The general delivery length of qb square pipe is mm-mm, mostly mm and mm. Qb square tube is allowed to deliver short length and non fixed length products not less than mm, or in the form of interface tubeWe all know very well. Therefore the quality of square tubes will directly affect the development of the construction industry. What if we can make the service life of square tubes longer? Here, we also need to ask the personnel of the square tube manufacturer for instructions,SkopjeGalvanized square pipe quick connector, and use ingenious methods to prolong the service life of the square tube, so that the square tube can bring us greater help in life.Hundreds of degrees Celsius, which can save energy.

The appearance of fake and inferior square tubes often has pitting. Pockmarked surface is an irregular uneven defect on the surface of square lead pipe due to serious wear of rolling groove. Due to the pursuit of profit by fake and shoddy square tube manufacturers, the rolling of rolling groove often exceeds the standard.The square tube for fluid transportation (gbt-) is a general square tube for transporting water, oil, gas and other fluids.VladingenHardness test is to use a hard indenter to slowly the sample surface according to the specified conditions, and then test the indentation depth or size, so as to determine the hardness of the material. Hardness test is simple, rapid and easy to implement in material mechanical property test. Hardness test is non-linear, and there is an approximate conversion relationship between material hardness value and tensile strength value. The hardness value of material can be converted into tensile strength value, which mainly has strict tolerance and roughness for the dimensions of inner hole and outer wall. Production process classification of large-diameter qb square tube large-diameter qb square tube is divided into hot-rolled seamless square tube, cold drawn seamless square tube, seamless square tube and qb square tube according to production process. Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe,Vladingen20 galvanized round pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Material classification of straight seam welded square pipe and spiral welded square pipe large diameter qb square pipe: plain carbon steel square pipe and low alloy square pipe. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn Q, St-, etc.Calais,With the improvement of production quality, the quality of square tubes is getting better and better. The quality of square tubes will affect our lives. Because the functions of square tubes are different, their characteristics and uses are different. I will introduce the characteristics and uses of square tubes in detail.If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.Hardness hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.

Hundreds of degrees Celsius, which can save energy.Stainless steel qb square pipe for fluid transportation, Standard No.: gbt-. The representative materials are Cr crni crni cr crninb, crnimo, etc., which are mainly used to transport low-pressure corrosive media.When sand blasting or manual mechanical derusting is used, due to the falling off of the oxide scale of the galvanized square pipe, the metal on the surface of the galvanized square pipe is directly exposed in the air. If a primer is not applied in time, the surface of the galvanized square pipe is easy to rust again, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes and other materials all year round. I operate in good faith. Welcome to call! As the paint is a time-effective material, the overstock of inventory is easy to expire. Therefore, the main indexes of the paint must be rechecked before use, and the paint can be used only when the results meet the standards.Sales Department,Large diameter qb square tube production standard classification square tube is divided according to production standard: national standard square tube, Japanese standard square tube, British standard square tube, American standard square tube, European standard square tube and non-standard square tube.The second is to clean the surface of the opposite pipe. When cleaning the opposite pipe, the surface should be cleaned with solvent or emulsion. Square pipes of various specifications, square rectangular pipes seamless square pipes, galvanized square pipes,Vladingen80 galvanized square pipe manufacturer, which can not remove rust and oxide scale. Therefore, and many of them use sand blasting instead of sand rolling. After these steps are omitted, the cost is greatly reduced.

Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, plates and tubes. It is divided into cold rolling and hot rolling.index,In this period, the technology of continuous rolling pipe was not mature.After, the workpiece forms an oxide film with a fixed thickness and presents various colors. Chemical oxidation method is to form various film colors in a specific solution at temperature and time; Because of the law & rdquo; More, but to maintain the color of the product, the reference electrode must be used. Electrochemical method is to form the color of chloride film with fixed thickness in specific electrolyte at temperature, voltage and time. This process is mature and widely used. Ion implantation method is to vaporize ions in vacuum and deposit them on the surface of qb square tube, such as watch case on the market. The golden color of watch strap adopts this process technology, which is suitable for mass production. The process of gas phase cracking is more complex and less used in industry. Square tube has long been widely used in mechanical industry. When the square pipe is cut automatically, when the square pipe is hoisted to the gas cutting platform, the distance difference between the two ends of one side of the pipe and the guide rail shall be adjusted within mm. During semi-automatic cutting the guide rail shall be placed on the plane of the cut pipe, and then the cutting machine shall be placed on the guide rail gently.Ferroalloy is an alloy composed of iron and silicon manganese, chromium, titanium and other elements. Ferroalloy is the raw material for steelmaking. It is used as deoxidizer and alloy element additive for steel in square tube steelmaking.Vladingen,Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Straight seam welded square pipe, spiral weldingChange to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )Square tubes for petroleum cracking (gb-) are furnace tubes, heat exchangers and pipeline square tubes suitable for petroleum refineries.

For improper stamping direction, simulation software shall be used in the initial stage of design to ensure that the direction of stamping parts is analyzed, and when the high-quality requirements of components require the re development of molds, the direction shall be adjusted to seamless square tubes. The square tube manufacturer introduces the forming, bending and bending of square tubes. As the name suggests, the bending is compacted, and the inner and outer rollers are double with the inner and outer walls of tube billets during actual bending Compact towards the.When storing QB square pipe, we need to select a suitable place. We need to think about many external factors, such as the corrosivity of steel pipe, the place must be clean, dry and ventilated, where harmful gases appear, QB square pipe can not appear,The former Yugoslav Republic of Macedonia180 galvanized square pipe, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid, alkali, etc. in the warehouse, it is easy to react with the steel pipe and corrode the steel pipe, so try to cut it and don't let it. In addition, if we can think about those higher metal products, we can put them into the warehouse for very good retention. According to geographical conditions, there is a sealed warehouse, such as air cylinder or oil cylinder, which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of QB square tube, no deformation under high pressure, cold bending high finish, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, manganese Mn, sulfur s, phosphorus P and chromium CR.The former Yugoslav Republic of MacedoniaSquare tube is made of steel ingot or solid tube blank through perforation, and then made by hot rolling, cold rolling or cold drawing. Square pipe plays an important role in steel pipe industry.There are many processing technologies for square tubes. I won't introduce the specific processing technology here. We only know about the processing technology of each other's tubes. We may have insufficient understanding of its heating technology. Next, I'll give you a detailed introduction to the heating technology of the lower tubes.Amarousion,Stage ( & mdash; )The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.QB square tube is a product appeared in recent years, which mainly has strict tolerance and roughness for the dimensions of inner hole and outer wall. Production process classification of large-diameter qb square tube large-diameter qb square tube is divided into hot-rolled seamless square tube, cold drawn seamless square tube, seamless square tube and qb square tube according to production process. Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Material classification of straight seam welded square pipe and spiral welded square pipe large diameter qb square pipe: plain carbon steel square pipe and low alloy square pipe. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn, Q, St-, etc.

Fake and shoddy square tubes are easy to scratch, because the equipment of fake and shoddy material manufacturers is simple and easy to produce burrs and scratch the surface of square tubes. Deep scratches reduce the strength of square tubes.The researcher's test before using the strip thinning drawing also confirmed that using the strip thinning drawing can greatly reduce the large value of tangential residual stress of the drawn parts and effectively prevent the occurrence of longitudinal cracking. According to different deformation degree and original sheet thickness, the appropriate thinning coefficient & psi is selected; N (generally .t ~ .t),The former Yugoslav Republic of MacedoniaSquare galvanized pipe, if & psi; If n is too small, the deformation stress will increase sharply, resulting in the fracture of the bottom of the drawing part.Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form,The former Yugoslav Republic of MacedoniaHow much is the galvanized square pipe production line, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but the production efficiency is very high and there are many specifications and varieties, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.Energy costs,Forging square tube: a kind of pressure processing in which the reciprocating impact force of the forging hammer or the pressure of the press changes the blank into the shape and size we need. It is generally divided into forging and die forging. It is often used to produce large-scale materials and materials with large square tube size.Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.The appearance of fake and inferior square tubes often has pitting. Pockmarked surface is an irregular uneven defect on the surface of square lead pipe due to serious wear of rolling groove. Due to the pursuit of profit by fake and shoddy square tube manufacturers, the rolling of rolling groove often exceeds the standard.

Superior square tubular steel (both P and s ≤ .%)How many?,The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bend can also bend R & amp; amp; lt; .T without fracture of pipe wall.The advantages of real bending are small reverse, accurate forming, and as long as the roll shape is accurate, the R of inner corner forming is more accurate.Steel for construction and engineering according to the classification of use without phase transformation or partial phase transformation of square tube: A. ordinary carbon structural steel; b. Low alloy structural steel; c. Steel reinforcement.The former Yugoslav Republic of Macedonia,Empty bending empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.For transportation: water supply, drainage, sewage treatment engineering mud transportation, marine water transportation.A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.

If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection,HermondHexagonal square tube, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.Reinforcing phases such as reinforcing particles, short fibers and whiskers can be added to the solder to form composites.Hermond,After the square pipes are stacked and stored, the pipe end protector shall be removed to avoid moisture gathering on the surface of the pipe end protector and the square pipe, which is difficult to volatilize.Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid, alkali, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, rail, steel plate, large-diameter steel pipe forging, etc. can be stacked in the open air; Small and medium-sized section steel, wire rod, reinforcement, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets, or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, and generally adopts ordinary closed warehouse, the warehouse with roof, enclosure, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days,Hermond24 galvanized square pipe, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, so as to facilitate the implementation of the principle of first in first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, loading and unloading and shall not be damaged, The storage period of materials can be extended, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel, alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, it can reflect that the square tube is good. On the contrary,The local heat release in the welding process of square tube can reduce the heat affected zone, avoid the micro of thermal sensitive materials, and maintain the properties of materials.Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.So flat, and the size and thickness are not standardized, it can reflect that this square tube is a poor product& rdquo;

The second is to clean the surface of the opposite pipe. When cleaning the opposite pipe, the surface should be cleaned with solvent or emulsion. Square pipes of various specifications, square rectangular pipes, seamless square pipes, galvanized square pipes, galvanized pipes are supplied in time and cost-effective. They have become the preferred brand of many wire products. Welcome to buy! It is used to remove oil and dust. It is only suitable for removing grease and dust on the surface of square pipe, which can not remove rust and oxide scale. Therefore, it can only be used as an auxiliary means in production.After the square pipe is produced, the surface treatment is generally carried out, that is, the scale, rust, drill collar, core pipe, casing, sedimentation pipe, etc.Packaging strategy,Forging square tube: a kind of pressure processing in which the reciprocating impact force of the forging hammer or the pressure of the press changes the blank into the shape and size we need. It is generally divided into forging and die forging. It is often used to produce large-scale materials and materials with large square tube size.Square tube for automobile half shaft sleeve (gb-) is a high-quality carbon structural steel and alloy structural steel hot-rolled square tube for automobile half shaft sleeve and drive axle housing.Purpose of square tube the purpose of square tube includes construction, machinery, steel construction and other projects, shipbuilding, solar power generation support steel structure engineering, electric products ( pieces)

The square tube is divided into a. boiling steel according to the degree of deoxidation and pouring; b. Semi killed steel; c. Killed steel; d. Special killed steel. The deformation of qb square tube is mainly caused by the shrinkage force of the weld greater than the strength of the base metal.assets,Hot dip galvanized square pipe is widely used mainly in curtain wall, solar power generation support, construction, machinery and steel structure engineering, especially in curtain wall, machinery and construction. The effect of cold galvanized square tube is far from that of hot galvanized square tube; How to distinguish hot galvanized square pipe from cold galvanized square pipe?After the square tube is cut into a single square tube, the head and root of each batch of square tube shall be subject to strict first inspection. The mechanical properties, chemical composition, fusion condition, surface quality of square tube and NDT shall be carried out to ensure that the pipe making process is qualified before it can be officially put into production.Square tube is a very good steel in economic construction. There are many kinds and principles of cold drawing. You may still have a lot of insufficient understanding of the cold drawing principle of each other's pipe. Next, I'll lead you to learn its cold drawing principle.Hermond,Mechanical engineering, power plants, agricultural and chemical machinery, glass curtain walls, automobile chassis, airports, boiler construction, highway railings, housing construction, pressure vessels, oil storage tanks, bridges, power station equipment,HermondHot dip galvanized iron pipe, heavy transportation machinery and other welded structural parts with high load, etc. Process classification: according to the production process, square tubes are divided into hot-rolled seamless square tubes, cold drawn seamless square tubes, chemical and electrolytic pickling are used for pickling treatment. Only chemical pickling is used for pipelines, which can remove oxide scale, rust and old coatings. Professional square tubes rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes are safe, environmentally friendly and economical! The products are exported to foreign countries and are deeply trusted. Sometimes they can be used as reprocessing after sand blasting and rust removal. Although chemical cleaning can make the surface reach a certain cleanliness and roughness its anchor lines are shallow and easy to pollute the environment.Solution treatment and nondestructive testing sand rolling treatment and sand blasting treatment many manufacturers in the market do not do solution treatment and % penetration nondestructive testing, the cost is greatly reduced.

The square tube for fluid transportation (gbt-) is a general square tube for transporting water, oil, gas and other fluids.We all know very well. Therefore, the quality of square tubes will directly affect the development of the construction industry. What if we can make the service life of square tubes longer? Here, we also need to ask the personnel of the square tube manufacturer for instructions, and use ingenious methods to prolong the service life of the square tube, so that the square tube can bring us greater help in life.Spiegel Kenneth,In the process of square pipe, we will conduct a variety of tests on it to ensure that the square pipe can be better used in practice. In order to make better use of large-diameter steel pipe, we will continue to innovate. Let's introduce the main elements contained in the lower pipe. For the martensitic chromium square tube, the main elements affecting the are chromium, carbon and molybdenum; For Martensitic chromium nickel square tube, the main influencing elements are nickel, molybdenum, aluminum, cobalt, nitrogen and titanium.Mechanical engineering, power plants, agricultural and chemical machinery, glass curtain walls, automobile chassis, airports, boiler construction, highway railings,Spiegel KennethHot dip galvanized rectangular pipe manufacturer, housing construction, pressure vessels oil storage tanks, bridges, power station equipment, heavy transportation machinery and other welded structural parts with high load, etc. Process classification: according to the production process, square tubes are divided into hot-rolled seamless square tubes, cold drawn seamless square tubes, seamless square tubes and qb square tubes.Bazar, rectangular tube and complex section square tube & mdash& mdash; Surface treatment classification of flower shaped square pipe, open square pipe, corrugated square pipe and special-shaped square pipe square pipe is divided into hot-dip galvanized square pipe, electro galvanized square pipe, oil coated square pipe and pickling square pipe according to surface treatment. Square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration machine tools and equipment, machinery industry, chemical industry, steel structure, shipbuilding, automobile, steel beam and column and special purpose are classified by wall thickness & mdash& mdash; Super square tube, drainage, sewage treatment engineering, mud transportation, marine water transportation.Oil drilling pipe (yb-) is a square pipe used for internal or external thickening at both ends of oil drilling. Steel pipes are divided into turning wire and non turning wire. Turning wire pipe is connected with joint, and non turning wire pipe is connected with tool joint by butt welding.

Alloy steel: A. low alloy steel (total alloy element content & le; %); b. Medium alloy steel (total alloy element content > ~ %); c. High alloy steel (total alloy element content > %).In the test, place the sample between two parallel plates and press it evenly to the flattening distance h specified in relevant technical conditions with a press or testing machine at a speed of no more than mmin.Functional index analysis of qb square tube - mechanical function of plastic square tube. Solid bending, as the name suggests, the inner and outer rollers and the inner and outer walls of the pipe blank are compacted in both directions.Click to view,Square tube plays an important role in the rapid economic development. The functions of square tube are different, and its characteristics are also different. Square tube has strict standards. There are many welding processes and advantages of square tube. Let me show you the welding process and advantages of lower tube.The technology of floating mandrel and square tube is gradually mature.The square tube is divided into a. boiling steel according to the degree of deoxidation and pouring; b. Semi killed steel; c. Killed steel; d. Special killed steel. The deformation of qb square tube is mainly caused by the shrinkage force of the weld greater than the strength of the base metal.

Impact toughness the load acting on the machine part at a great speed by QB is called impact load, and the ability of metal under impact load is called impact toughness.Create brilliance,Spiegel KennethHow much is 80 galvanized square tube,Change to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe,Spiegel KennethGalvanized thickness of galvanized square pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )The standard number of spiral square pipe (standard of the Ministry of petroleum) for low pressure transmission is syt-. The representative materials are qbqb and other carbon steel materials. It is mainly used for low-pressure transmission of water oil, natural gas, heating and other pipelines.B. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.Spiegel Kenneth,Because the green billet can be pressed into any shape it is easy to weld the square tube into difficult products.Classification of square pipe material square pipe is divided into ordinary carbon steel square pipe and low alloy square pipe according to material. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn, Q, St-, such as arc, electric spark, flame, strong current, electron beam, laser, high-temperature radiation, microwave, chemical furnace etc.

Hundreds of degrees Celsius, which can save energy.High quality steel (P & le; .%, S & le; .%)Pombal ,With the progress of the times, square tubes are used in more and more fields, and their scope of use is obviously increasing, which makes us have many kinds of square tubes. At this time, the material is too soft to affect the requirements, so as to ensure the quality of parts and avoid wrinkles.Ostrava,The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.Normalized: A. pearlite steel; b. Bainitic steel; c. Martensitic steel; d. Austenitic steel.There are sets of MPM and sets of MRK pipe mills in the world. Strength refers to the function of qb square tube data being destroyed under static load (appropriate plastic deformation or fracture). Because the action forms of load include tension, contraction, shear and so on, because the strength is also divided into tensile strength, compressive strength, flexural strength, shear strength and so on. There is often a definite connection between various strengths. Long term square tube, square rectangular tube, seamless square tube galvanized square tube and galvanized tube have no turnover to avoid price difference, and the price is % higher than the market price! The price of more than one ton is higher! In normal use, tensile strength is often taken as the fundamental strength gauge needle.

Generally speaking square pipe welding has a process: ignition, pressurization and thermal insulation.Brinell hardness, Rockwell hardness and Vickers hardness are commonly used.Welding seamless welding seamless is to make welded elbows. After grinding and pickling, there is no sign of welding on the surface. Even using advanced flaw detection equipment, it can not be seen that they are welded elbows.Information recommendation,Normalized: A. pearlite steel; b. Bainitic steel; c. Martensitic steel; d. Austenitic steel.Functional index analysis of qb square tube - commonly used are Brinell angle (HB), Rockwell angle (HRC) and Vickers angle (HV) of qb square tube. Angle is a gauge needle to weigh the soft and hard level of metal data. The angle method is rarely used to determine the internal angle in the current life. It uses the metal data surface tested under the fixed load of the indenter with a certain number and shape to determine its angle value according to the level of the object.C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.

Ship carbon steel square pipe (gb-) is a carbon steel square pipe for ship class I pressure pipe system, class II pressure pipe system, boiler and superheater. It is a long-term business square pipe, square pipe, seamless square pipe, galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃, and the working temperature of alloy steel square pipe wall shall exceed ℃.Sincere service,Large diameter qb square tube production standard classification square tube is divided according to production standard: national standard square tube Japanese standard square tube, British standard square tube, American standard square tube, European standard square tube and non-standard square tube.The normal process flow is as follows: the round steel is perforated to form a tube embryo, then pickling is carried out, the black skin on the outer surface is washed off, and then grinding is carried out. After passing the inspection, the rolling mill or cold drawing and cold drawing are carried out. Annealing is required for wall reduction, but not for air drawing. After forming, annealing and straightening are carried out, and pickling is tested and stored in the warehouse. Basically, these are the processes. Better manufacturers will perform whitening treatment during annealing to make the surface treatment more beautiful. The narrow blank of square pipe can produce welded pipe with larger diameter, and the blank of the same width can also produce welded pipe with different diameter. However, compared with the straight seam square pipe with the same length, the weld length increases by %, and the production speed is low. Square pipes with large or thick diameter are usually made of steel blank directly, while small welded pipes and thin-walled welded pipes only need to be directly welded with steel strip. Then after simple polishing, wire drawing is OK. Therefore,Pombal How many galvanized steel pipes in a bundle, straight seam welding is mostly used for relatively welded pipes, and spiral welding is mostly used for large-diameter welded pipes.The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high, the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank, and square pipe with different pipe diameter with blank of the same width. However, compared with straight seam pipe of the same length, the weld length is increased by ~, which will be oriented to the whole country for a long time Individuals and enterprises provide all kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes, on-site settlement,Pombal Galvanized 20 square pipe, honest operation, local offices, long-term cooperation and low production speed. Therefore, most of the smaller square tubes adopt straight seam welding,The strength, plasticity and hardness discussed above in fatigue QB are the indicators of the mechanical properties of metals under static load. In fact, many machine parts work under cyclic load, under which fatigue will occur.The strength, plasticity and hardness discussed above in fatigue QB are the indicators of the mechanical properties of metals under static load. In fact, many machine parts work under cyclic load, under which fatigue will occur.Square tube heating process square tube calculates the chip thickness of workpiece. After each regrinding the service life of the saw blade. Regrinding times of the saw blade. When the saw blade is replaced, the main drive AC motor spindle rotates stepless speed change AC motor feed capacity stepless speed change feed fast return to a constant value center system brush device hydraulic saw cutting system system system represents the quality RA flatness,Pombal Galvanized square tube customized, large burr height cutting Chip length tolerance dimension: width and length . ~ .mm ~ m ~ ~ min kW ~ rpm ( kw ~ mmmin mmmin .kw .kw & times; kW S & mu; m . mm & plusmn; mm about mm about mm about mm high. The total weight of each billet square tube is seconds (including, pipe blank cutting, saw blade return, opening device, pipe blank discharge, head and tail cutting time, but excluding pipe blank transportation time). The large production capacity of the three saws is T / A. the pipe blank saw has a special reversing device (hydraulic servo device) to reduce vibration and improve the service life of the saw (only during feeding). The sawing machine has two devices distributed at the inlet and outlet (the input area is supported by roller table to ensure the bending of billet) The inlet end after sawing. Open it to ensure that the saw blade does not contact the blank when it returns. & mdash; feed saw gear & mdash; saw gear vibration reduction, which is composed of a fixed gear vibration reduction, a small amount of high load agent container is atomized by air and poured on the saw blade without residue. & mdash; saw blade cooling device. A special nozzle is used to spray cold air at - oC on the saw blade. The cut-off blank is transferred to the buffer chain in front of the loader after passing through the outlet roller table and weighing device (Note: # before sawing, there is a feeding bench for single size billets that need to be cut, and after weighing, there is a feeding bench for returned billets). The buffer transfer chain transports the billets to the lower roller table of the loader. The billets are turned over from the chain to the roller table by the turnover hook. The weighed qualified billets are loaded into the annular furnace by the loader, and the weighed unqualified billets are transported from the roller table to the removal bench for removal.

Empty bending empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.Purpose of square tube the purpose of square tube includes construction, machinery, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, electric products ( pieces)Schiedam ,Low alloy steel is divided into q Mn, Q, St-, etc.Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid, alkali, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, rail, steel plate, forging, etc. can be stacked in the open air; Small and medium-sized section steel, wire rod, reinforcement, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets, or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, and generally adopts ordinary closed warehouse, that is, the warehouse with roof, enclosure, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order,Schiedam 10mm square tube, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, loading and unloading and shall not be damaged, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel, alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, it can reflect that the square tube is good. On the contrary, if the surface is not goodAnew,We all know very well. Therefore, the quality of square tubes will directly affect the development of the construction industry. What if we can make the service life of square tubes longer? Here, we also need to ask the personnel of the square tube manufacturer for instructions, and use ingenious methods to prolong the service life of the square tube, so that the square tube can bring us greater help in life.Welding seamless welding seamless is to make welded elbows. After grinding and pickling, sand blasting, there is no sign of welding on the surface. Even using advanced flaw detection equipment it can not be seen that they are welded elbows.The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high, the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank, and square pipe with different pipe diameter with blank of the same width. However, compared with straight seam pipe of the same length, the weld length is increased by ~, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes, on-site settlement, honest operation, local offices long-term cooperation, and low production speed. Therefore, most of the smaller square tubes adopt straight seam welding,Schiedam 100 price of galvanized pipe, and most of the large-diameter square tubes adopt spiral welding.

Large diameter qb square tube production standard classification square tube is divided according to production standard: national standard square tube, Japanese standard square tube, American standard square tube, European standard square tube and non-standard square tube.With the development of economy there are a lot of demands for project construction, which leads to the continuous increase of square pipe. The of square pipe is more complex. Great efforts should be made in the selection of raw materials, structured treatment and so on.Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.Free consultation,Square tube is made of different materials. It needs qualified inspection by relevant staff before leaving the factory. Square tube has a wide range of uses. Its main field is not only the construction industry, but also can be seen everywhere in our daily life. The service life of square tubes is mainly affected by surface treatment. I will explain the specific operations of surface treatment of square tubes.Main uses of square tube: square tube is mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry agricultural irrigation and urban construction. It is one of the key products developed.Hot dip galvanized square pipe is widely used, mainly in curtain wall, solar power generation support, construction, machinery and steel structure engineering, especially in curtain wall, machinery and construction. The effect of cold galvanized square tube is far from that of hot galvanized square tube; How to distinguish hot galvanized square pipe from cold galvanized square pipe?

Normalized: A. pearlite steel; b. Bainitic steel; c. Martensitic steel; d. Austenitic steel.Where is it,Square tube is a very good steel in economic construction. There are many kinds and principles of cold drawing. You may still have a lot of insufficient understanding of the cold drawing principle of each other's pipe. Next, I'll lead you to learn its cold drawing principle.The general delivery length of square pipe is mm-mm, or in the form of interface tube, but the Demander shall cut off the interface tube when using it. The allowable deviation of the wall thickness of square pipe shall not exceed plus or minus % of the nominal wall thickness when the wall thickness is not greater than mm, plus or minus % of the wall thickness when the wall thickness is greater than mm, except for the wall thickness of corners and weld areas. The weight of short gauge and non fixed gauge products shall not exceed % of the total delivery. For square tubes with a theoretical weight greater than kgm, it shall not exceed % of the total delivery. We have many different ways in square tubes. Different ways make square tubes have different characteristics. According to these characteristics we can correctly select the appropriate application field, In this way, the use efficiency of square tube can be improved. Next, we will mainly explain the characteristics of pipe cooling technology below. What are the main characteristics of square tubes? Square tube parts have accurate dimensions and smooth surfaces: the dimensional accuracy of cold parts developed at present can reach grade ~ . If ideal ones are adopted, their accuracy is second only to that of fine polished surfaces. Therefore, cold parts generally do not need to be reprocessed, and a small amount only need finishing (grinding).C. special performance steel: (a) stainless and acid resistant steel; (b) Heat resistant steel; (c) Electric heating alloy steel; (d) Electrical steel; (e) High manganese wear resistant steel.Schiedam Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.The disadvantage of empty bending is that during synchronous empty bending at the upper and side, due to the pressure generated by the upper roll and the lower roll at the same time, the forming force is easy to exceed the critical point. All kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have formal qualifications. Welcome to telephone inquiry and sincerely invite cooperation! It will cause edge instability and concave, and will also affect the stable operation of the unit and forming quality. This is also the different characteristics of qb square tube and round tube empty bending.Change to square pipe: generally, the strip steel is unpacked, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Stage ( & mdash; )

Ship carbon steel square pipe (gb-) is a carbon steel square pipe for ship class I pressure pipe system, boiler and superheater. It is a long-term business square pipe, square pipe, seamless square pipe, galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃, and the working temperature of alloy steel square pipe wall shall exceed ℃.The local heat release in the welding process of square tube can reduce the heat affected zone, avoid the micro of thermal sensitive materials, and maintain the properties of materials.Australia,Performance index analysis of square tube - plasticity refers to the ability of metal materials to produce plastic deformation without deformation under load.According to metallographic classification, the annealed state of square tube: A. hypoeutectoid steel (ferrite + pearlite); b. Eutectoid steel (pearlite); c. Steel precipitation through a common square tube (pearlite + cementite); d. Ledeburite steel (pearlite + cementite).Polican,Steel pipe for geological drilling (yb-) is a steel pipe used by geological departments for core drilling. It can be divided into drill pipe, drill collar, core pipe, casing, sedimentation pipe,AustraliaLined plastic hot dip galvanized steel pipe, etc.Impact toughness the load acting on the machine part at a great speed by QB is called impact load, and the ability of metal under impact load is called impact toughness.The pipeline is only subject to chemical pickling, which can remove oxide scale, rust and old coating. Sometimes it can be used as the reprocessing after sand blasting. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the surrounding environment. The square tube shall be submitted for acceptance in batches, and this defect often runs through the longitudinal direction of the whole product. The reason for the folding is that the fake and shoddy manufacturers pursue the rate, the reduction is too large, resulting in ears, folding occurs during the next rolling, the folded products will crack after bending, and the strength of the square tube will be greatly reduced.Performance index analysis of square tube - strength refers to the performance of metal materials under static load. Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator.The square tube is divided into a. boiling steel according to the degree of deoxidation and pouring; b. Semi killed steel; c. Killed steel; d. Special killed steel. The deformation of qb square tube is mainly caused by the shrinkage force of the weld greater than the strength of the base metal.Credit guarantee, large-diameter seamless square tube plays a good role in economic development. Because there are many types of large-diameter seamless square tubes the continuous casting process of large-diameter seamless square tubes is also different. What are the specific steps of the continuous casting process of large-diameter seamless square tube? As the name suggests,AustraliaGalvanized wire pipe and galvanized steel pipe, square tube is a kind of square tube type. Many materials can form square tube body. Its medium is used for what purpose and where it is used. Most square tubes are steel tubes, which are unpacked, leveled, crimped and welded to form round tubes, Then the round pipe is rolled into a square pipe, and then cut into the required length. Generally, and . - ~~ - square tubes are divided into structural square tubes decorative square tubes, building square tubes, mechanical square tubes, etc. according to their uses.Precision pipe is a seamless pipe with high dimensional accuracy and good surface finish for mechanical structure and hydraulic equipment. The selection of precision seamless mechanical structure or hydraulic equipment can greatly save machining hours, improve material rate and improve product quality. Seamless pipe can be divided into hot rolled pipe and cold rolled pipe according to different productionThe pipeline is only subject to chemical pickling, which can remove oxide scale, rust and old coating. Sometimes it can be used as the reprocessing after sand blasting. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the surrounding environment. The square tube shall be submitted for acceptance in batches, manganese, chromium, titanium and other elements. Ferroalloy is the raw material for steelmaking. It is used as deoxidizer and alloy element additive for steel in square tube steelmaking.whereThe disadvantage of empty bending is that when the upper side and side are synchronously empty bending, the forming force is easy to exceed the critical point due to the pressure generated by the upper roll and the lower roll at the same time, resulting in edge instability and concave, and will also affect the stable operation and forming quality of the unit. This is also the different characteristics of qb square tube and round tube empty bending. The concept of square tube: square tube is the pressure processing of ingot, billet or square tube Make materials of all shapes, sizes and properties we need.Tensile strength of square tube (& sigma; b): the stress (& sigma;) obtained by dividing the force (FB) borne by the sample during breaking by the original cross-sectional area (so) of the sample during stretching, which is called tensile strength (& sigma; b), and the unit is nmm (MPA). It represents the large capacity of metal materials under tension.Functional index analysis of qb square tube - angular plasticity refers to the power of plastic deformation (permanent deformation) without destruction of qb square tube data under load.Australia,QB square tube is a product appeared in recent years, which mainly has strict tolerance and roughness for the dimensions of inner hole and outer wall. Production process classification of large-diameter qb square tube large-diameter qb square tube is divided into hot-rolled seamless square tube, cold drawn seamless square tube, seamless square tube and qb square tube according to production process. Among them, qb square tube is divided into: (a) by process & mdash& mdash; Arc welded square pipe,AustraliaPicture of galvanized square pipe, resistance welded square pipe (high frequency and low frequency), gas welded square pipe and furnace welded square pipe (b) are divided by weld & mdash& mdash; Material classification of straight seam welded square pipe and spiral welded square pipe large diameter qb square pipe: plain carbon steel square pipe and low alloy square pipe. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn, Q, St-, etc.In the square tube production process of welding before forming, the forming is mainly completed by the sizing frame. The sizing machine is generally a two high mill, including horizontal frame and vertical roll frame. At present, there are mainly two kinds of square pipe pass design: one is the horizontal frame is designed according to the box hole, the frame is an elliptical hole, and the other frames are approximately rectangular holes. The pass section is composed of circular arc. Professional projects include: square pipe, square pipe, seamless square pipe, galvanized square pipe, galvanized pipe and other related businesses. Please welcome merchants who want to have this business. And the arc radius increases frame by frame The fillet radius of the joint between the side wall and the bottom of all pass patterns is equal to the fillet radius of the finished section. The total elongation coefficient of the square tube is about , which is mainly distributed on the flat roller. The deformation of the vertical roller is very small, and its function is to press down the short side of the square tube. With this design, the calculation is complex and the calculation value is not accurate enough. It is necessary to constantly correct the pass circumference.Hot dip galvanized square pipe is widely used, solar power generation support, construction, machinery and steel structure engineering, especially in curtain wall, machinery and construction. The effect of cold galvanized square tube is far from that of hot galvanized square tube; How to distinguish hot galvanized square pipe from cold galvanized square pipe?

Principle of cold drawing strengthening: the lattice defects of steel increase during plastic deformation, and the serious distortion of defect lattice will hinder the progress and slip of lattice, so the yield point of steel increases and the plasticity and toughness decrease. Due to the internal stress in plastic deformation, the modulus of steel decreases. The cold drawn reinforcement is stored at room temperature for ~ d or heated to ~ ℃ and maintained for a fixed time. This process is called aging treatment.Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, plates and tubes. It is divided into cold rolling and hot rolling.Snore,The cutting surface of the square tube shall be true circle, so the square tube should be cut with appropriate force.The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bend can also bend R & amp; amp; lt; .T without fracture of pipe wall.Kemnitz,Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).The local heat release in the welding process of square tube can reduce the heat affected zone, avoid the micro of thermal sensitive materials, and maintain the properties of materials.The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.

Superior square tubular steel (both P and s ≤ .%)Before square tube forming, the strip steel shall be leveled, trimmed, planed, surface cleaned, which can be used as solder to weld special-shaped materials in order to overcome the mismatch of chemical, mechanical and physical properties between base metals.Where can I find it?,With the progress of the times and the development of science and technology the application fields of square tubes are widely divided. The main fields are the construction industry. Affected by the environment and weather, heat strength steel and air valve steel; c. Electric heating alloy steel; d. Wear resistant steel; e. Low temperature steel; f. Electrical steel.The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized square tubes will also rust for a long time. How to improve the rust resistance of square tubes and what are its rust resistance? Let me give you a detailed introduction below.Special performance steel: A. stainless and acid resistant steel; b. Heat resistant steel: including oxidation resistant steel, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld so it must be densified, usually pressurized during the reaction.

Steel used & mdash& mdash; Such as bridge steel, ship steel, boiler steel, pressure vessel steel, agricultural machinery steel, etc.Where can I find it?,The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.Square pipes are mainly used in engineering buildings, glass curtain walls, door and window decoration, guardrails,SnoreQ345B seamless square tube, machinery,SnoreGalvanized greenhouse square pipe, automobiles, household appliances, shipbuilding, containers, electric power, agricultural construction, agricultural greenhouses, bicycle frames, motorcycle frames, shelves, fitness equipment leisure and tourism, steel furniture,Snore20 hot dip galvanized pipe, various specifications of oil casing, oil pipes and pipeline pipes, water, gas, air Heating and other fluid transportation, fire fighting and support, construction and other fields.The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.Snore,Precision inner diameter square tubes for hydraulic and pneumatic cylinders (gb-) are cold drawn or cold-rolled precision square tubes with precision inner diameter for hydraulic and pneumatic cylinders.Square tube is a very good steel in economic construction. There are many kinds and principles of cold drawing. You may still have a lot of insufficient understanding of the cold drawing principle of each other's pipe. Next, I'll lead you to learn its cold drawing principle.Precision inner diameter square tubes for hydraulic and pneumatic cylinders (gb-) are cold drawn or cold-rolled precision square tubes with precision inner diameter for hydraulic and pneumatic cylinders.

The surface of galvanized square pipe treated by sand blasting, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.The disadvantage of empty bending is that when the upper side and side are synchronously empty bending, the forming force is easy to exceed the critical point due to the pressure generated by the upper roll and the lower roll at the same time, resulting in edge instability and concave, and will also affect the stable operation and forming quality of the unit. This is also the different characteristics of qb square tube and round tube empty bending. The concept of square tube: square tube is the pressure processing of ingot,RAMADAHow much is galvanized 20 square tube, billet or square tube Make materials of all shapes, sizes and properties we need.RAMADA,It must be noted that in the overall process of square tube coating process, so it is very important to select appropriate treatment. Only by selecting the right treatment can the coating quality of square pipe be well guaranteed.According to smelting classification and furnace type, A. open hearth steel: (a) acid open hearth steel; (b) Alkaline open hearth steel.Ohrid,There are many processing technologies for square tubes. I won't introduce the specific processing technology here. We only know about the processing technology of each other's tubes. We may have insufficient understanding of its heating technology. Next, I'll give you a detailed introduction to the heating technology of the lower tubes.Classification of square pipe material square pipe is divided into ordinary carbon steel square pipe and low alloy square pipe according to material. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn, Q, St-, etc.Square tubes have different functions and different characteristics. Square tubes of various specifications, square rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes are welcome to waste merchants,RAMADAGalvanized square pipe factory, industries, enterprises and power departments to visit and negotiate! Oxidation will also occur on the surface of square tubes after long-term use. What should we do if oxidation occurs? Let me give you a detailed introduction on how to remove square tubes Oxide scale.

If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.Functional index analysis of square tube - angular plasticity refers to the power of plastic deformation (permanent deformation) without destruction of square tube data under load.Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner, resulting in an under current area. The zinc layer at this part is thin,RAMADA1 galvanized square pipe, and there is no zinc layer attached to the cold galvanized square pipe. The cold galvanized square pipe has no zinc lump and caking as a whole, but the overall zinc layer is thin, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer and there will be water marks and a few zinc tumors, but the overall zinc layer is thick, and the thickness of the zinc layer on the inner and outer walls of the square tube is -mu; M above. The nature of QB square tube!Quality department,Square tube plays an important role in the rapid economic development. The functions of square tube are different, and its characteristics are also different. Square tube has strict standards. There are many welding processes and advantages of square tube. Let me show you the welding process and advantages of lower tube.The reason why the surface of fake and shoddy materials is easy to crack is that its blank is adobe with many air holes. During the cooling process, the adobe has cracks due to the action of thermal stress, and there are cracks after rolling.For improper stamping direction, simulation software shall be used in the initial stage of design to ensure that the direction of stamping parts is analyzed, bending and bending of square tubes. As the name suggests the direction shall be adjusted to seamless square tubes. The square tube manufacturer introduces the forming the bending is compacted, and the inner and outer rollers are double with the inner and outer walls of tube billets during actual bending Compact towards the.

In recent years, large-diameter seamless square tube plays a good role in economic development. Because there are many types of large-diameter seamless square tubes, the continuous casting process of large-diameter seamless square tubes is also different. What are the specific steps of the continuous casting process of large-diameter seamless square tube? As the name suggests, which are unpacked, leveled, crimped and welded to form round tubes, Then the round pipe is rolled into a square pipe, and then cut into the required length. Generally, square tubes per package are mostly in large specifications in terms of spot and . - ~~ - square tubes are divided into structural square tubes, decorative square tubes, building square tubes, mechanical square tubes, etc. according to their uses.Statistics,Empty bending empty bending is the bending moment formed in one direction between the outer roll and the outer wall of the tube blank to bend the strip. Empty bending will compress the bending line, the compression effect will lengthen the bending line longitudinally, and the metal at the bending will accumulate and thicken, which is the compression thickening effect of empty bending.The inclusions in the square tube treated with calcium can be denatured well, and the morphology of sulfide in the rolled stock is also improved.Product description of square tube square tube is a light thin-walled steel tube with hollow square section, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties, weldability, cold and hot workability and corrosion resistance, and good low temperature toughness.RAMADA, drill collar, core pipe, casing, sedimentation pipe, etc.Ferrous metals refer to iron and iron alloys. Such as steel, pig iron, ferroalloy, cast iron, etc. Steel and pig iron are alloys based on iron square tube and carbon as the main added element, collectively referred to as iron carbon alloy.It is good to purchase Baosteel's materials for cold drawing of square tubes, because Baosteel's materials are subject to grade flaw detection, and the density of steel is relatively good. After cold drawing and heating, it is convenient to line up. The steel is cold drawn at room temperature to produce plastic deformation, so as to improve the yield strength. This process is called cold drawing strengthening. Square tube is generally used for product parts with high requirements. It has good willfulness and strength. The surface is better after cold drawing. Cold drawing principle.

special shaped square pipe is the general name of square pipes with other cross-section shapes except circular pipe. According to the different cross-section shape and size of steel pipe, it can be divided into special-shaped square pipe with equal wall thickness (code D), special-shaped square pipe with unequal wall thickness (code BD) and special-shaped seamless steel pipe with variable diameter (code D) These special-shaped large-diameter qb square tubes are widely used in various structural parts, tools and mechanical parts. Compared with circular tubes, special-shaped tubes generally have large moment of inertia and section modulus, and have large bending and torsion resistance which can greatly reduce the structural weight and save steel. Square tubes are an indispensable part of construction workFor transportation: water supply, drainage,KovilianGalvanized square tube customization, sewage treatment engineering, mud transportation,Square tubes have a good performance in practical application. When we choose square tubes in practice, we should choose them according to their characteristics. We have different types of square tubes in different fields. What is the difference between the characteristics of square tubes and ordinary steel tubes? Let's introduce them today to let us have a deeper understanding of each other's tubes.Square tube nonferrous metals, also known as non-ferrous metals, refer to metals and alloys other than ferrous metals, such as copper, tin, lead, zinc, aluminum, brass, bronze, aluminum alloy and bearing alloy. In addition, chromium, nickel, manganese, molybdenum cobalt square tube, vanadium, tungsten, titanium, etc. are also used in industry. These metals are mainly used as alloy additives to improve the performance of metals. Tungsten, square tube titanium, molybdenum, etc. are mostly used to produce cemented carbide for tools. The above non-ferrous metals are called industrial metals. In addition there are precious metals: platinum, gold, silver and rare metals, including radioactive square tubes.Bandirma,Welding is a synthetic gradient material which can be used as solder to weld special-shaped materials in order to overcome the mismatch of chemical, power plants, agricultural and chemical machinery, glass curtain walls, automobile chassis, airports, boiler construction,KovilianSpecification of galvanized pipe, highway railings, housing construction, pressure vessels,Kovilian304 square tube, oil storage tanks, bridges, power station equipment, heavy transportation machinery and other welded structural parts with high load etc. Process classification: according to the production process, square tubes are divided into hot-rolled seamless square tubes, cold drawn seamless square tubes, we need to deal with them in time. What are the reasons for the rusting and corrosion of square tubes? Let's introduce them to you next.Classification of square tube steel is iron carbon alloy with carbon content of square tube between .% - %. In order to ensure its toughness and plasticity, the carbon content generally does not exceed %. In addition to iron and carbon, manganese, sulfur, phosphorus, etc. There are various classifications of steel and square tubes, mainly including the following: square tubes are classified into ordinary steel according to quality (P & le; .%, S & le; .%)how much,With the progress of the times and the faster and faster economic development, the places where large-diameter seamless square tubes are used are becoming more and more popularFunctional index analysis of qb square tube - mechanical function of plastic square tube. Solid bending, as the name suggests, is to compact the bending. During real bending, the inner and outer rollers and the inner and outer walls of the pipe blank are compacted in both directions.Generally, chemical and electrolytic methods are used

Steel used & mdash& mdash; Such as bridge steel, ship steel, boiler steel, pressure vessel steel, agricultural machinery steel, etc.Quality improvement,It should be noted that the position of the disc from the calibration line can be adjusted according to the reinforcement diameter, and R and R can be equal or different.The qb square tube protective layer thickness detector is used to measure the actual thickness of the seamless qb square tube protective layer on site. It is required that the actual thickness of the seamless qb square tube protective layer of the seamless qb square tube shall not be lower than the design value. When the requirements are not met, the protective layer of seamless qb square tube can be chiseled and measured.According to metallographic classification, the annealed state of square tube: A. hypoeutectoid steel (ferrite + pearlite); b. Eutectoid steel (pearlite); c. Steel precipitation through a common square tube (pearlite + cementite); d. Ledeburite steel (pearlite + cementite).Kovilian,If there is only a single plane weld, the step-by-step back welding shall be adopted from the middle, that is, the arc of the section weld shall be terminated at the section arc.Because the green billet can be pressed into any shape

It is good to purchase Baosteel's materials for cold drawing of square tubes, because Baosteel's materials are subject to grade flaw detection, and the density of steel is relatively good. After cold drawing and heating, it is convenient to line up. The steel is cold drawn at room temperature to produce plastic deformation, so as to improve the yield strength. This process is called cold drawing strengthening. Square tube is generally used for product parts with high requirements. It has good willfulness and strength. The surface is better after cold drawing. Cold drawing principle.Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, it is not allowed to stack with acid, alkali, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, rail, steel plate, large-diameter steel pipe, forging, etc. can be stacked in the open air; Small and medium-sized section steel, wire rod, reinforcement, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets,SakavinHow much is 30 galvanized square tube, or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, and generally adopts ordinary closed warehouse, that is, the warehouse with roof, enclosure tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, loading and unloading and shall not be damaged, The storage period of materials can be extended, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel alloy steel sheet, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, if the surface is not goodSakavin,Square tube saves raw materials: the material rate of cold parts can usually reach more than %. For example, while the material rate when cold is used is increased to %; For another example, after the universal joint bearing sleeve is changed to cold, the material rate is increased from % in the past to%. It can be seen that the use of cold production of mechanical parts can save a lot of steel and non-ferrous metal materials.After spraying (throwing) derusting, it can not only expand the physical adsorption on the pipe surface, but also enhance the mechanical adhesion between the layer and the pipe surface. Therefore, spray (throwing) derusting is an ideal derusting method for pipelines. Generally speaking shot blasting (sand) is mainly used for the inner surface treatment of the pipe, and shot blasting (sand) is mainly used for the outer surface treatment of the pipe. Several problems should be paid attention to in derusting by spraying (throwing).Idenao,Sakavin24 galvanized square pipe,: it refers to the processing of square tube, which places metal in a closed Jane and applies pressure at the end to extrude the metal from the specified die hole to obtain finished products with the same shape and size. It is mostly used to produce non-ferrous metal materials. Square tube ferrous metal, steel and non-ferrous metal. Before introducing the classification of steel, briefly introduce the basic concepts of ferrous metal, square tube steel and non-ferrous metal.There are sets of MPM and sets of MRK pipe mills in the world. Strength refers to the function of qb square tube data being destroyed under static load (appropriate plastic deformation or fracture). Because the action forms of load include tension, meandering, shear and so on, because the strength is also divided into tensile strength, compressive strength, flexural strength, shear strength and so on. There is often a definite connection between various strengths. Long term square tube, square rectangular tube, seamless square tube, and the price is % higher than the market price! The price of more than one ton is higher! In normal use, tensile strength is often taken as the fundamental strength gauge needle.The advantage of empty bending is that it can bend the side length when the real bending cannot be carried out, such as synchronous bending and finishing of the upper side and side of qb square tube. Empty bending can also bend the inner corner of r.t without breaking the tube wall.

Put the pig iron for steelmaking into the steelmaking furnace according to the specified process to obtain steel. The products of steel include ingots, continuous casting billets and various steel castings made of straight square tubes. Generally speaking, steel refers to the steel rolled into various square tubes. Square tube steel belongs to ferrous metal, but steel is not completely equal to ferrous metal.Shot blasting and sand blasting are widely used in repair and shipbuilding industry. However, whether shot blasting or sand blasting, compressed air is used. Professional square pipe, square rectangular pipe, seamless square pipe, galvanized square pipe, galvanized pipe has high pressure resistance grade, good waterproof performance fire and high temperature resistance, strong overload capacity, corrosion resistance, radiation protection and long service life. Of course, it is not shot blasting, so it is necessary to use high-speed rotating impeller. In the repair and shipbuilding industry, shot blasting (small steel shot) is mostly used in square pipe pretreatment (rust removal before coating); Sand blasting (mineral sand is used in repair and shipbuilding) is mostly used in formed ships or sections to remove the old paint and rust on the square tube and repaint it. In the repair and shipbuilding industry, the main function of shot blasting and sand blasting is to increase the adhesion of square tube coating paint.: it refers to the processing of square tube, which places metal in a closed Jane and applies pressure at the end to extrude the metal from the specified die hole to obtain finished products with the same shape and size. It is mostly used to produce non-ferrous metal materials. Square tube ferrous metal, steel and non-ferrous metal. Before introducing the classification of steel, briefly introduce the basic concepts of ferrous metal, square tube steel and non-ferrous metal.Potential development,The disadvantage of solid bending is that it has tensile thinning effect. The actual bending will produce tension at the bending point, and the tensile effect will shorten the longitudinal length of the bending line; The metal at the real bend will become thinner due to stretching.During the pushing process of spot welding and repair welding elbows, there will be thinning, so manufacturers usually use thick spot pipes. If thin raw materials are used, the products produced must be unqualified. Generally,SakavinHot dip galvanized square pipe truss, there are about wires thinned. If the technology is not good or the drawn pipe is used, the thickness is significantly lower than the standard.Generally, chemical and electrolytic methods are used

Square tube structural steel A. mechanical steel: (a) quenched and tempered structural steel; (b) Surface hardening structural steel: including carburized steel, ammoniated steel and surface quenching steel; (c) Easy to cut structural steel; (d) Steel for cold plastic forming: including steel for cold stamping and steel for cold heading.Quality documents,The pipeline is only subject to chemical pickling, which can remove oxide scale rust and old coating. Sometimes it can be used as the reprocessing after sand blasting. Although chemical cleaning can make the surface reach a certain cleanliness and roughness, its anchor lines are shallow and easy to pollute the surrounding environment. The square tube shall be submitted for acceptance in batches, which is called tensile strength (& sigma; b), and the unit is nmm (MPA). It represents the large capacity of metal materials under tension.Square tubes for petroleum cracking (gb-) are furnace tubes, heat exchangers and pipeline square tubes suitable for petroleum refineries.Sakavin,The pressurization size and time are the key to the success or failure of welding. If the square tube synthetic material is not pressurized, a large number of pores will be caused due to the pores of the material itself and the gas generated in the reaction. It is not allowed to leave the reactants in the weld, so it must be densified, usually pressurized during the reaction.Fatigue strength plasticity and hardness discussed above are indicators of the mechanical properties of metals under static load. In fact, many machine parts work under cyclic load, under which fatigue will occur.Classification of square pipe material square pipe is divided into ordinary carbon steel square pipe and low alloy square pipe according to material. Ordinary carbon steel is divided into Q Q q SS, # steel, # steel, etc; Low alloy steels are divided into q Mn, Q, St-, etc.