The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, oil depots, chemical industry and power departments of enterprises and institutions to transport oil products and flammable and explosive liquids. The operating temperature should also be within ℃.　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.Ijebu-Ode,　　For example, concentrate and tailings are treated in the concentrator, ash and slag are removed from the power plant, slime and dense medium coal are transported in the coal preparation plant, and slurry is transported in coastal river mining operations. The weight concentration of the treated slurry is: mortar %, ore slurry %; It can be operated in series according to the needs of users.　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.　　Water or air leakage in the pipeline. The nut may not be tightened during installation. If the leakage is not serious, the air or water leakage can be treated with cement or cement slurry mixed with asphalt oil. Temporary repairs can be done with some wet mud or soft soap. If water leaks at the water pump joint, tighten the nut with a wrench. as

　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　 Lifting, loading and unloading of electric pump: remove the cable and disconnect the power supply.　　In fact, the pumps I am going to talk about here have a wide range of uses. Pumps are required for both civil and military purposes as well as for advanced technologies, chemical especially in the mining, metallurgical and other industrial sectors. It is a widely used general mechanical equipment. Most pumps are corroded or severely corrodedSafety production,　　Moreover, the leaked flammable explosive and toxic liquid will cause fire, and the consequences will be unimaginable.　　The equipment is integrated with the oil cooler, with compact layout. The water pump meets the modular and integrated design requirements of diesel engine parts. The joint surface with oil cooler adopts rubber sealing method, which has good sealing effect. Submersible slurry pump is a kind of solid-liquid mixing medium with the help of centrifugal force　　Second, the power used is not matched,JamshedpurCentrifugal slurry pump, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline,JamshedpurQJ submersible pump, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing bodyTotal quality assurance,　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.　　In order to improve the service life of the submersible sewage pump, most domestic and foreign manufacturers are now trying to find a way on the pump protection system, that is, in case of leakage, overload, over temperature and other faults of the pump, it can give an automatic alarm and automatically shut down for maintenance. However, we believe that in the submersible sewage pump　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.Jamshedpur,　　 If the head of the submersible slurry pump is too low or the head is higher than the practical condition, the flow will be large and the current will rise. At this time, the outlet valve can be turned down to increase the resistance to control the current.　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s,JamshedpurSmall deep well pump, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performance