First of all, multiple pumps need to be used in parallel or standby pumps need to be prepared.　　 If the head of the submersible slurry pump is too low or the head is higher than the practical condition, the flow will be large and the current will rise. At this time,KetakWQ submersible sewage pump, the outlet valve can be turned down to increase the resistance to control the current.Ketak,　　 absorb silt from various stone processing plants.　　Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump, tighten the adjusting screw of the bearing box evenly, and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ, When δ= A (. ~ mmVenissieux,KetakSubmersible sewage pump,　　Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced which maximizes the reliable operation of the mechanical seal and greatly extends its service life　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.　　 When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.

　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumping　　 Disassembly of water pump: use a disassembly wrench to remove the water inlet joint by left rotation, and use a disassembly cylinder to impact the conical sleeve at the lower part of the pump. After the impeller is loose, take out the impeller,KetakScrew deep well pump, conical sleeve, and remove the guide housing. In this way, the impeller, guide housing, upper guide housing, check valve, etc. are unloaded in turn.　　Potential energy pumping water up high. However, once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?analysis,　　Occurrence of personal injury accident. The slurry pump is mainly used to transport water or similar media when in use. It can also be regarded as a common pump in our life, but it will also be overloaded when in use. Let&#;s have a look today　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.　　Slurry pump Inappropriate model is selected when selecting the pump. In actual use, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pump

　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate, the repair is timely, and the delivery life will be long, and regularly add or replace the smooth oil during the work, and the interval and writeInstallation works　　.　　Consider the vertical separation level of the tail equipment. The water pump control cabinet has a variety of protection s and complete status display, such as overload, short circuit, phase loss protection, pump body water leakage, motor over temperature and electric leakage, as well as single pump and multi pump control working modes, a variety of main and standby pump switching modes and various　　In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, our basic survival is a problem.Ketak,　　In addition to the main impeller inside the equipment a set of impeller for mixing will be added at the bottom of the equipment, so that the equipment can be used without its　　 add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve, inject a small amount of water into the water compressor to divert water. When the hand pump discharges water, it means that the pump is full　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced, and the income has been increased.