It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф . Anchor bolt structure for M assembly: The fixed boarding bridge is composed of mechanical system, hydraulic system, and electrical system. The platform and chassis form a mechanical system. The platform is based on&quo; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of kilometers/hour when the forklift is fully loaded without bending, improving work reliability.Firstly, as the fixed hydraulic boarding bridge is used to complete the rapid loading and unloading of goods through height adjustment plates, there are certain strict requirements for the quality and material selection of height adjustment plates to avoid the occurrence of defective materials, which will result in unexpected loss of performance in the application process.Anshan,Install anti rolling foot skirts on both sides to prevent accidental injury to the toe platform.Its design is usually fully standardized as early as the structural design of buildings.Khaniá,The guide sleeve has air holes, sand holes, shrinkage, and other conditions. Generally, there is a problem with the casting, which is the quality of the oil cylinder itself. At this time, it is necessary to find a manufacturer to replace the new boarding bridge. Normally, this situation does not occur in the casting oil cylinder. The above two reasons are due to the occurrence of excessive oil leakage, and frequent inspections should be conducted in these two areas. Hydraulic loading and unloading bridge is a specialized auxiliary equipment that maintains rapid loading and unloading of goods during the application process. The height adjustment function of the equipment makes the bridge in the middle of the truck guide sufficient to be built. Lifting platforms, trucks, and hydraulic loading and unloading bridges are commonly used cargo loading and unloading equipment.Point. The DCQY type is a hand operated variable amplitude type, operated by a hand pump, which can achieve variable amplitude on the bridge board without the need for power supply; Widely used in mobile loading and unloading places without loading and unloading equipment and loading and unloading platforms; It is a safe, reliable, time-saving, land-saving logistics machinery that solves high-altitude differential operations.The instrument equipment instrument inspection (inspection and testing) method utilizes various instruments to measure the hydraulic system, hydraulic components' performance (xì ng né ng), parameters, and analyze and process these data (ch ǔ l ǐ) To determine the location of the fault. A mature lifting platform manufacturer in China, with complete products and quality assurance.

Point. The DCQY type is a hand operated variable amplitude type, operated by a hand pump, which can achieve variable amplitude on the bridge board without the need for power supply; Widely used in mobile loading and unloading places without loading and unloading equipment and loading and unloading platforms; It is a safe, reliable, time-saving land-saving logistics machinery that solves high-altitude differential operations.Secondly, before using the hydraulic boarding axle,AnshanHydraulic fixed boarding axle, it is also necessary to check if there is any oil in the reducer, abnormal noise, and excessive temperature rise in the housing. If there is any oil leakage, it is necessary to check the oil level in the housing, if there is insufficient oil, and add oil. If there is any abnormal noise or rapid temperature rise, repair it in a timely mannerAt the beginning, and pay attention to whether it can be used correctlyWork courses,The overall module of the water inlet pipe of the hydraulic boarding bridge must have a reasonable hydraulic system during the application process, so that the equipment has excellent airtightness and a long service life, and the height of the equipment is fixedAnti collision block: This device can effectively protect buildings and boarding bridges from damage.The overall module of the water inlet pipe of the hydraulic boarding bridge must have a reasonable hydraulic system during the application process, so that the equipment has excellent airtightness and a long service life and the height of the equipment is fixed

In general, there are several reasons for hydraulic cylinder oil leakage: damage to the oil seal ring on the cylinder, etc. The cylinder body of the oil cylinder is damaged. Oil leakage caused by defects such as air holes,AnshanFixed electric hydraulic boarding bridge, sand holes, and shrinkage porosity in the guide sleeve.Excellent quality,Insufficient understanding of the operating conditions of the axle. Assuming you understand some fundamental principles and the three elements that lead to success, you can ensure that you are in excellent working form for a long time. Inspection before use of mobile boarding bridge: Check if the oil unloading valve is tightened. Use of mobile boarding bridge: Use a hand pump to raise the boarding bridge to the required position and height; Place the tongue plate on the box and connect the safety chain to the box; Place the wheel mask in a suitable position next to the tire; Release the manual oil unloading valve to make the oil cylinder and wheels in a natural state, loading and unloading can begin; Precautions for operation: Keep the oil cylinder in a relaxed state during use; Both electric and manual lifting must turn off the manual pump switch.Assuming that the manufacturing quality of fixed hydraulic boarding bridges is not satisfactory, the reasons for their shortcomings are mostly preventive repairs,The hydraulic boarding bridge is mainly made of anti slip thick steel plates during the production and manufacturing process, and all equipment can provide good anti slip characteristics to a certain level in operation and application. The hydraulic press loading bridge is a specialized auxiliary equipment that maintains rapid loading and unloading of goods. Its height adjustment function creates a bridge between the large truck and the cargo platform in the warehouse. Transport vehicles such as electric forklifts can immediately enter the large truck to carry out mass loading and unloading of goods also known as the loading and unloading service platform. That way, the device can loosen the return valve button during the lowering process thereby reducing the weight of the device.Hydraulic boarding bridges can reduce economic and component costs to a certain extent. In the process of applying mechanical equipment, unexpected common faults may sometimes occur, which may lead to safety accidents. In fact, such devices themselves will also be equipped with certain security protection.Vibration acoustic method: Vibration acoustic instruments detect the vibration and noise of hydraulic systems, and identify the wear (a basic type of component failure) and technical status of hydraulic components according to the laws of vibration acoustics. Based on this, location, degree, nature, and development trend of faults. Nowadays, with the rapid development of the logistics industry, the demand for logistics equipment is becoming increasingly weak, and auxiliary improvements such as fixed hydraulic boarding bridges and fixed lifting channels, as well as the increase in loading and unloading equipment usage, have been made. Some manufacturers have now achieved export to foreign countries!