The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Inner Mongolia,The shafts in the middle of the support rods of the hydraulic lifting platform are inconsistent, causing the lifting platform to fail to work normally, the platform is severely damaged, and the table is tilted. Please check carefully that the general scissor aerial work platform has not been strictly tested before leaving the factory,Inner Mongolia10 ton lifting cargo elevator, and it has been put into the market. Caused a lot of accidents to take place, for the tilt detection, the detection of this link is not very concerned about for the majority of small enterprises, which is why there are such a large number of lifting equipment to have this problem. Problems with the oil cylinder and the power unit system are often caused by insufficient power and unqualified quality of the oil cylinder, which is also a problem that the enterprise itself needs to pay attention to.Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.Vallensbaek,Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads, and different brand awareness, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons, the height is meters, the table size is mm*mm, the price is about yuan. Rated load, lift height, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.

Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.The manufacturer adjusts the relief valve of the hydraulic lifting platform to the best state before delivery. If the customer adjusts it at will during use, it will cause the internal pressure to fluctuate. In severe cases, the service life of the motor will be shortened; Especially in summer, pay attention to the heat dissipation of the hydraulic lifting platform during use. If the temperature is too high, it is easy to burn out the circuit; Do not underestimate these actions, which can save you a lot of unnecessary after-sales.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements,The surface of the brushes of each part should be kept clean, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably,Inner MongoliaChain guide rail lifting cargo elevator, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.

Prepare the foundation according to the foundation plan, pay attention to the alignment, and alignment to ensure the level of the foundation and various requirements for use.Inspection standard,The last thing to note is that, compared with the lifting platforms in some places protective fences are generally added on the platforms. Since the lifting platforms are special equipment, so when the personnel ask you if you want to add a guardrail the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.Simple, in fact, some details should be paid attention to, as follows: It is actually difficult to insert them into the shaft pins when over-installing the bearings, but sometimes, some people think of hammering the bearings for convenience. When using brute force, in fact,Inner MongoliaGuide rail chain elevator, using a hammer to directly hit the bearing will cause great damage to the bearing, which is the main reason for bearing damage and reducing the service life of the bearing. Therefore, we must not overdo it when installing the bearing. It is best to put some soft cloth or cardboard on it before installing.As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight so special attention should be paid to regular maintenance and inspection to avoid accidents.Inner Mongolia,Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, carpets and floors are protected from humidity. Rusty fittings.The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, throttle valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.