When using an electric mobile scissor lifting platform outdoors, if the wind force exceeds level , please stop using it; When the lifting height exceeds meters, the wind ropes at the four corners of the hydraulic lift platform should be tightened and fixed, and the support legs should be reinforced for protection and stability to avoid safety accidents caused by excessive swinging of the electric lifting platformVehicle mounted lifting platform is widely used for high-altitude operations in hotels buildings, stations airports, sports venues, workshops, warehouses, and other places; It can also be used as temporary high-altitude lighting, advertising, etc.Baotou,In on-site hydraulic elevators, it is difficult to detect the rising position, middle position,BaotouManual hydraulic lifting platform, impact noise, and oil film leakage of hydraulic cylinders. Field observations have shown that the excessive lifting speed of the hydraulic cylinder has led to an increase in failure rate, seriously affecting production efficiency. The unstable hydraulic lifting requires an analysis of the hydraulic oil flow rate. Hydraulic pressing oil has poor quality and contains a large amount of impurities, which can also prevent slow and unstable lifting. In addition, there are other reasons: lifting the composition of the hydraulic ring. Oil pump, safety valve, directional valve, directional valve, one-way throttle valve (without throttling),BaotouGuide rail hydraulic lifting platform, because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.Dehradun,Remove the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts to avoid dust when removing the system oil pipe. Clean the disassembled parts before opening them. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap, loosen the tank cap, and remove any remaining debris from the joint (do not rinse with water to prevent water from seeping into the tank). After confirming cleaning, open the tank cap.The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within .MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it is necessary to exhaust the air in a timely manner.Materials enter the production line at one end of the factory building, and the production process ends at the other end of the factory building with multiple separate platforms; This can greatly shorten the distance of material flow in the factory building.

Volume speed control circuit: Speed control is achieved by adjusting the displacement of a variable pump or variable motor.Low power consumption: Hydraulic elevators are driven by the pressure generated by their own weight, greatly saving energy. Long term improvement of various brand products such as elevator manufacturers, with complete designated products and quality assuranceThe precautions to consider when selecting a hydraulic lift oil tank include: considering the structure of the oil tank, the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank, with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end, so that the distance Z between the inlet and return oil is far, The hydraulic oil tank has more heat dissipation effect.average method, disassembling, and adjusting the rotating mechanism, attention should be paid to ensuring that the middle line is parallel to the middle line of the gear and its meshing surface is not less than %. The meshing clearance should be suitable for the brakes of each mechanism. The clearance between the brake wheels should be regularly checked and adjusted to ensure its flexibility and reliability. There must be no dirt on the friction surface and it must be cleaned with gasoline or diluent.Lifting mechanism: The workbench should be ensured to rise and fall smoothly, and there should be no jumping lifting phenomenon. All moving parts should be flexible when moving, and there should be no jamming devices. The lifting system of the elevator is divided into electric or manual hydraulic systems, pipelines, and joints.What are the methods for reducing shaking on lifting platforms? Reducing the shaking of the lifting platform can reduce the psychological obstacles of the operators ensure the smooth progress of the operation, and also greatly help improve safety. Warm reminder: safety, do not operate blindly. Lifts are widely used in many places, and their working principles vary. Today, we will analyze the working principles of elevators. The types of elevators are generally divided into the following: fixed elevators, This type of elevator uses hydraulic oil cylinders and pump stations to transmit power, in the form of a scissor fork type. According to customer requirements, the length of the support rod for the scissor fork, the number of layers, the angle of the angle axis, and the expansion and contraction of the oil cylinder complete the lifting operation. Its advantages are large load-bearing capacity, stable lifting, and high safety.

If the circuit of the device is not disconnected or lowered, it is necessary to check the fuse for repair and replacement.Free consultation,The elevator itself has a simple structure and is easy to maintain, also known as hydraulic powered elevators.The hydraulic system of the fixed lifting platform of the hydraulic cargo elevator is equipped with anti fall and overload safety protection devices, and operation buttons can be set on each floor and the lifting platform workbench to achieve multi-point operation.Do not use hydraulic lifting equipment with malfunctioning issues. The problem should be resolved before carrying cargo.Baotou,BaotouDouble fork hydraulic lifting platform,After long-term use of the automatic lifting platform equipment, it is inevitable that some malfunctions will occur. In order not to affect work, it is necessary to promptly solve the difficulties in starting the motor and abnormal sounds. Generally, due to overload, insufficient power supply, and a small cross-sectional area of the power supply cable, the starting voltage drop is too large and the price of the cargo elevator is reduced.The precautions to consider when selecting a hydraulic lift oil tank include: considering the structure of the oil tank, the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank, with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end, so that the distance Z between the inlet and return oil is far, The hydraulic oil tank has more heat dissipation effect.What are the methods for reducing shaking on lifting platforms? Reducing the shaking of the lifting platform can reduce the psychological obstacles of the operators ensure the smooth progress of the operation, do not operate blindly. Lifts are widely used in many places, and their working principles vary. Today, we will analyze the working principles of elevators. The types of elevators are generally divided into the following: fixed elevators, This type of elevator uses hydraulic oil cylinders and pump stations to transmit power, in the form of a scissor fork type. According to customer requirements, the length of the support rod for the scissor fork, the number of layers, the angle of the angle axis, and the expansion and contraction of the oil cylinder complete the lifting operation. Its advantages are large load-bearing capacity, stable lifting, and high safety.