In fact, the impeller clearance of submersible slurry pump is not adjustable for all types of pump, but it is adjustable. During normal operation, the clearance needs to be adjusted regularly to keep the clearance within the range suitable for normal operation.　　 When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.Guwahati , and conduct hydrostatic test if necessary.Rust’avi,　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.

　　 The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!　　AHR slurry pump is also a double pump casing structure, and the pump body and pump cover are equipped with replaceable corrosion-resistant rubber lining (including impeller, front sheath, rear sheath, etc.). The pump body and cover are the same as those of ah type slurry pump, and its transmission part and installation form are the same as those of ah and L type slurry pumps.　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.original,　　 We must choose to consider the actual use situation when making the selection, because there will be some difference between the marked head when using and the head when using. This is because the pipe itself　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps,Guwahati Self priming slurry pump wholesale, and transmits energy to the slurry medium to generate a certain flow rate the motor shaft drives the water pump impeller to rotate, drive the solid flow, and realize the transportation of slurry.

　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example,Guwahati Screw deep well pump, when the submersible slurry pump is used at ordinary times, air holes usually appearInspection items,　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.　　The submersible sewage pump is a kind of pump product which is connected with the motor and works under the water at the same time. Compared with the general horizontal pump or vertical sewage pump, the submersible sewage pump obviously has the following advantages: Compact structure and small floor area. Submersible sewage pump is submerged　　When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium so thatGuwahati ,　　The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned.　　The mixing impeller and other main flow passage parts are made of high wear-resistant materials, which are wear-resistant, corrosion-resistant, non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothing　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section,Guwahati Deep well pump, stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve