What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads, and different brand awareness,Castle Peak CityHydraulic cargo elevator and lifting cargo elevator, the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters table size mm *mm, the price is about - yuan; the rated load is - tons,Castle Peak CityFactory freight elevator lifting, the height is meters,Castle Peak CityElevating cargo elevators require, the table size is mm*mm, the price is about yuan. Rated load, lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.Castle Peak City,In the process of developing the guide rail elevator machinery, in order to ensure the use of the heavy platform under safe conditions and maintain compliance with relevant rules and regulations, the heavy platform is specially formulated, and the safety operating procedures are formulated as follows: It must be equipped with qualified and certified lifting equipment.Professional operators who are qualified and certified to work on lifting platforms. Operators working on lifting platforms should wear safety belts. When working in a live area, the car body should be grounded according to regulations. The climbing operation of the heavy platform should be commanded by the operator, and the operator should communicate with the operator of the heavy platform according to the standard signal. The announcement signal should be clear and accurate. The guide rail lift is safe and convenient to use. The guide rail lift usually lifts the lower arm first, then the middle arm, and then the upper arm. During the reversing operation of the lifting platform, the lower arm must be reversed after being raised and lowered at a certain height. Inversion response is slow. Pay attention to whether the distance between the scissor arm and the platform meets the safety requirements of each equipment. For a long time, we provide all kinds of elevator factories for individuals and enterprises across the country, settle accounts on site, operate with integrity, and have offices in various places for long-term cooperation.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)SalaberrydeValleyfield,Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)

Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Replace with new oil, do not use old oil intermittently otherwise the moving parts in the system will accelerate wear.The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, explosion-proof electromagnetic reversing valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.Where can I find it?,Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.System: explosion-proof electronic control system, remote control system, P IC system.

Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that,Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Elevators are very popular now, and they can easily send goods to tall buildings. Among them, hydraulic lifts are more popular among people, and people can choose the one that suits them according to their actual situation. However, you must pay attention to the lifting speed of the hydraulic lift when you are working normally, so as not to make mistakes. So what factors will affect the lifting speed of the hydraulic lift?Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.Castle Peak City,Today, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat and in severe cases, the winding will be burned.Unscrew the screw on the dust-proof hole outside the flange of the elevator adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.