Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.Curva ,Regular inspection and maintenance, elimination of hidden dangers, and troubleshooting are all good for improving work efficiency, prolonging the service life of equipment and ensuring the safety performance of the elevator.Walking: assisted self-propelled, two-wheel traction, self-driving,Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time,Curva 1 ton small lifting cargo elevator, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers carpets and floors are protected from humidity. Rusty fittings.

The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.It is necessary to bandage and replace the damaged part in time. The elevator is a kind of hydraulic elevator, also known as the guide rail hydraulic elevator, which is suitable for the transportation of goods higher than buildings, restaurants and hotel floors. Next, Lipusheng Machinery will introduce to you the daily maintenance of the elevator.Secondly, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.Marketing Department,Fixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, materials on and off the assembly line,Curva Oil pressure track lifting cargo elevator, parts lifting during large-scale equipment assembly, and fixed three-dimensional parking. So what is the new price of the fixed lift?The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.

Fixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, materials on and off the assembly line parts lifting during large-scale equipment assembly, and fixed three-dimensional parking. So what is the new price of the fixed lift?Welcome calls ,Curva Simple guide rail type cargo elevator,The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.Avoid, and avoid rain and snow during work.What types of lifts are there? There are many types of this equipment for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, a special lifting device is required to be fixed at a certain position of the production line.Curva ,The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.