strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally.　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choiceArak,　　Conduct a comprehensive preventive maintenance once a year, including: replace all O-ring seals; Check the bearing wear and add new grease; Check the wear condition of the mechanical seal to determine whether it needs to be replaced; Check the wear of the impeller and the seal between the impeller and the pump body　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue, industrial cooling, farmland irrigation, seawater lifting, ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersibleVertientes,　　There is no need to equip auxiliary mixing or spraying equipment, and the operation is simpler. The equipment is directly submerged for operation, without noise and vibration, and the site is cleaner.　　Potential is convenient and flexible. It is easy to operate. It can be operated by a fool who turns on the power supply under immersion; It has a wide range of applications. In many cases, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.

　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceeds　　 tailings transportation, various tailings ore, pulp pulp, coal slurry, slag, etc.　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand,ArakSubmersible sewage pump, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pumpsupply,　　Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people　　The fruit is also bad; When the axial flow pump is used, its water output is relatively large, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from one　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use, that is, in the traditional slurry pump

　　Schematic diagram of vertical slurry pump II. Why does the demand for submersible slurry pump increase greatly? From the perspective of market demand, although the absolute number of submersible slurry pumps has not exceeded that of vertical slurry pumps, it has a rapid development momentum, mainly due to the convenience and flexibility mentioned above; In addition,ArakWQ submersible sewage pump, for submersible slurry pumphow,　　Pressure. Therefore a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.　　Correct the main shaft of the water pump and adjust the position of the water pump and the motor relatively.　　There are differences.Arak,ArakLong shaft submerged slurry pump,　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.　　Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, the service life of slurry pump in this section is generally low. Of course, different minerals, abrasion　　With water, you can start working.