From the surface coating, there are aluminum oxide, melamine and piano paint. Look at the surface of the board.Shtep, Use large-scale floor renovation machinery to polish the floor for many times, remove about .mm of paint layer, surface layer and wood layer, and make the floor surface in a new state of fine and smooth after fine sand.The floor corners are ground with a small grinder to make the whole smooth.In short,ShtepWhat is the thickness of wood floor, floor leather is a layer of synthetic plastic decorative products. In addition to many advantages such as wear resistance, pollution resistance, moisture resistance, small water absorption, simple construction, convenient maintenance and low price, warm in winter and cool in summer of wood floor, narrowing the gap between wood floor and wood floor. No wonder floor leather will be so popular.If you are also worried about the shortcomings of wood flooring,ShtepEnvironmentally friendly wood flooring, you might as well consider floor leather materials.Plastic floor leather has the advantages of light weight, elasticity, good mechanical strength, good foot feeling strength foot feeling, wear resistance, pollution resistance, corrosion resistance,ShtepFloor care essential oil, heat insulation, sound insulation, moisture resistance, small water absorption, good insulation, self extinguishing, easy cleaning simple construction, convenient maintenance and low price. In a large number of civil buildings and public places, factories with high requirements for cleanlinessIt is widely used in the laboratory.Plastic floor leather belongs to soft floor. It is a floor roll produced by coating or calendering on sheet continuous substrate with polyvinyl chloride resin as the main raw material and appropriate additives.The length of each roll of plastic floor leather is m ~ m, the width is mm ~ mm, and the total thickness is mm (household) ~ mm (public building).Limassol, Main performance.People who have a certain understanding of the manufacturing process of composite wood flooring should know that adhesive is essential, but the whole process of SPC flooring is not adhesive (adhesive releases formaldehyde at high temperature), and is more and more loved and used by owners.However, it does not refer to formaldehyde, but refers to that the formaldehyde emission is less than .mg/l, and the harm is small.Second soak in water.

High concentration formaldehyde is a genotoxic chemical.In animal experiments, high concentration inhalation in the laboratory can cause nasopharyngeal tumors.If the scratch is serious and the floor paint is damaged and white, some countermeasures need to be taken.Third, look.reform, raw material parts, growth and development parts and lower sawing points it will inevitably cause inconsistent color difference.The first is cleaning to remove oil stains or dust;The second is leveling. The convex part shall be shoveled and polished. The concave part can be made into paste with glue and cement at the weight ratio of :, leveled with a spatula, and then leveled with sandpaper after drying.After the ground is flat, clean and dry, it can be glued and paved.Gluing is the last process before paving, glue shall be applied on the ground according to the size of the floor paint cloth, and one piece shall be paved in this order.A width of cm shall be reserved at the joint of the floor paint cloth. No glue shall be applied first, so that the joint can be treated finally.When the glue coated on the ground feels sticky by hand, it can be paved. When pasting, pay attention to aligning the sidelines, and use a long handle floor brush to blow out and compact.The joints are generally spliced by overlapping cutting and the overlapping width is about cm.Align the long steel ruler with the center of the overlap, cut with a cutter along the ruler, then remove the cut edge strips (note that there should be two edge strips, don&#;t forget to take out the lower one), apply an appropriate amount of glue to the joint with a paint brush, and then close and compact the joint with a pressing roller.The residual glue extruded at the joint shall be wiped clean to avoid affecting the appearance.Then apply a thin layer of joint liquid along the joint.Finally, check whether there are bubbles and whether they are flat.If there are bubbles, use a syringe to insert and suck out the air, and then compact it.Finally, use washing powder to remove the residual glue marks on the lacquer cloth. If they cannot be removed, they can be wiped with alcohol.In this way, the whole process will be completed.Due to the improvement of the living standards of Chinese residents, the grade of interior decoration is also rising, and the decoration materials are increasingly developing towards the fixed decoration direction of elegance, high profile, long service life and good effect.As for the ground, the service life of paint, carpet or ordinary floor leather and floor brick is not as long as that of ground lacquer cloth.thickness

In particular, the previous agency said that the laminate floor is a waterproof floor, which is only the surface layer. In fact, the only taboo in the application of laminate floor is small blisters.Free consultation,What is the difference between solid wood flooring and solid wood composite flooring?Second, mild to moderate scratches.PVC flooring has certain bacteriostatic properties. Some excellent PVC flooring are added with bacteriostatic agents in the production process, which has a strong ability to remove most bacteria and inhibit bacterial reproduction.Therefore, the natural environment with high requirements for disinfection and sterilization, such as PVC floor in hospital consulting room, is the most ideal choice.Shtep, The conventional thickness is only -mm. The ultra-thin design is a bold innovation in the professional industry. The surface is printed with materials to improve the service life of people flow field. The surface imitates the real wood texture and natural marble texture. In view of the characteristics of raw materials, it has fast heat conduction and long heat storage duration. It is the preferred floor for floor heating. Exposure to obvious sunlight, or significant increase or decrease in room temperature, will cause early embrittlement of solid wood board floor paint, which should be minimized. A foot pad shall be placed in front of the door to reduce the wear of sand on the floor.