B. low alloy structural steel C. ordinary structural steel and high-quality steel for specific purposes (including high-quality steel)Special performance steel: A. stainless and acid resistant steel; b. Heat resistant steel: including oxidation resistant steel, heat strength steel and air valve steel; c. Electric heating alloy steel; d. Wear resistant steel; e. Low temperature steel; f. Electrical steel.Skiff,After the process of polishing, the surface effect of the square tube is quite good. The quality of the polishing process directly affects the external image of the square tube. Therefore, we must choose the appropriate polishing according to the above, and pay more attention to the polishing process of the square tube.Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.Monsanto,Ship carbon steel square pipe (gb-) is a carbon steel square pipe for ship class I pressure pipe system, class II pressure pipe system, boiler and superheater. It is a long-term business square pipe, square pipe, seamless square pipe galvanized square pipe and galvanized pipe. Welcome to consult. The working temperature of carbon steel square pipe wall shall not exceed ℃,SkiffGalvanized steel pipe, because Baosteel's materials are subject to grade flaw detection and the working temperature of alloy steel square pipe wall shall exceed ℃.It is good to purchase Baosteel's materials for cold drawing of square tubes, and the density of steel is relatively good. After cold drawing and heating, it is convenient to line up. The steel is cold drawn at room temperature to produce plastic deformation, so as to improve the yield strength. This process is called cold drawing strengthening. Square tube is generally used for product parts with high requirements. It has good willfulness and strength. The surface is better after cold drawing. Cold drawing principle.Hardness hardness is a pointer to measure the hardness and softness of metal materials. At present, mainly in curtain wall, solar power generation support, construction,Skiff6 points galvanized square pipe price, especially in curtain wall, the steel pipe whose ratio of outer diameter to wall thickness is less than is called square pipe. At present, the square tubes produced by qb square tube factory are mainly used in tap water engineering, petrochemical industry, chemical industry, electric power industry, agricultural irrigation and urban construction. For transportation: water supply and drainage. For gas transmission: gas, steam and liquefied petroleum gas. For structure: for punchingAccording to metallographic classification, the annealed state of square tube: A. hypoeutectoid steel (ferrite + pearlite); b. Eutectoid steel (pearlite); c. Steel precipitation through a common square tube (pearlite + cementite); d. Ledeburite steel (pearlite + cementite).Test conclusion,Hot dip galvanized square tube is a kind of square tube which is welded after using steel plate or steel strip to curl and form, and on the basis of this square tube, the square tube is placed in the hot dip galvanized pool and formed through a series of chemical reactions; The production process of hot-dip galvanized square pipe is relatively simple, but the production efficiency is very high and there are many specifications and varieties, but this kind of square pipe needs little equipment and capital, which is more suitable for the production of small galvanized square pipe manufacturers.Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.After cold drawing and aging treatment, the yield point is improved, the tensile ultimate strength is also increased, and the plasticity continues to decrease. Due to the reduction of internal stress during aging, the modulus can be basically restored. According to this principle, cold drawing or cold drawing of reinforcement or low carbon steel wire rod is often carried out on site or prefabricated component factory, so as to improve yield strength and save steel.

Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, plates and tubes. It is divided into cold rolling and hot rolling.Quality documents,Classification of square tube steel is iron carbon alloy with carbon content of square tube between .% - %. In order to ensure its toughness and plasticity, the carbon content generally does not exceed %. In addition to iron and carbon, the main elements of steel also include silicon, manganese sulfur, phosphorus, etc. There are various classifications of steel and square tubes, mainly including the following: square tubes are classified into ordinary steel according to quality (P & le; .%,SkiffQuotation for galvanized square pipe of 46, S & le; .%)Shot blasting is a high-speed rotating impeller that throws small steel shot or small iron shot out and hits the surface of the square tube at high speed, so the oxide layer on the surface of the square tube can be removed. At the same time, the steel shot or iron shot impacts the surface of the square tube at high speed, resulting in lattice distortion and deformation on the surface of the square tube, increasing the surface hardness, which is the main reason for the surface deformation of the square tubeBecause the green billet can be pressed into any shape, it is easy to weld the square tube into difficult products.Skiff,The surface of galvanized square pipe treated by sand blasting shot blasting or pickling process is relatively clean, and the oxide scale and rust are removed, which improves the adhesion of the coating. When the installation site unconditionally adopts sand blasting and shot blasting, manual and mechanical derusting can be adopted, but the derusting quality level must be reached.Welding seamless welding seamless is to make welded elbows. After grinding and pickling, there is no sign of welding on the surface. Even using advanced flaw detection equipment, it can not be seen that they are welded elbows.Steel for construction and engineering according to the classification of use without phase transformation or partial phase transformation of square tube: A. ordinary carbon structural steel; b. Low alloy structural steel; c. Steel reinforcement.