Formula for hydraulic test pressure of stainless steel welded pipe for weight calculation fluid (gbt-): where: P - test pressure, MPa; R - stress, taking yield point of %, MPa; s - nominal wall thickness of steel pipe, mm; D - Nominal outer diameter of steel pipe,Stainless hot plate (grade I) GB- stainless cold strip (grade I)Stainless steel has two classifications: one is divided into chromium stainless steel and chromium nickel stainless steel according to the characteristics of alloy elements; The other is divided into m stainless steel, f stainless steel, a stainless steel and A-F duplex stainless steel according to the microstructure of steel in normalized state.Rimnicu Vilcea,Since the back is not filled with argon, which is suitable for installation on the construction site. However mainly for its simplicity and low cost, due to its structural characteristics, flux cored welding wire has high requirements for welders during operation, with fast wire feeding speed and high wire feeding accuracy. It is difficult to master. Welders should be specially trained and skilled before they can participate in welding in Yangba, Nanjing And foreign construction sites, we have successfully solved the problem that argon cannot be passed through the junction and repair port.Decorative stainless steel pipe: usually the outer wall is relatively bright, so its name is considered. Decorative stainless steel pipe is used for decorative purposes. The stainless steel pipe for general decorative purposes is relatively thin. Because it is different from the manufacturing process of stainless steel product pipe, the price also varies greatly. The general production process of decorative stainless steel pipe is ordinary welded stainless steel pipe. Guangdong stainless steel product pipe stainless steel product pipe: generally,Jiguani304 stainless steel with magnetic, the surface of stainless steel product pipe is also a bright surface, and a small number of pipes with acid pickling industrial surface. As mentioned above, stainless steel product pipe belongs to the purpose of stainless steel products, because the outer diameter size, mechanical properties, acid, alkali and corrosion resistance of stainless steel pipe are relatively good, Therefore, stainless steel pipes are generally used as anti-corrosion materials or hardware products in large-scale production enterprises. The production process of stainless steel pipes is one-time forming, and nitrogen protection is also added during welding.When the stainless steel fixed port is welded, it will be difficult to ventilate on both sides of the weld. At this time, how to ensure the argon filling protection on the inner side of the weld has become a difficult problem. For a long time, facing the national high price,Jiguani06cr18ni11ti stainless steel plate, the reasonable price and perfect service of all kinds of stainless steel plates, stainless steel belts and stainless steel pipes have been recognized by the majority of customers. In the actual construction on site, we use two welding joints The above problems were successfully solved by plugging with water-soluble paper on the side, ventilation from the weld center and sealing with adhesive tape on the outside (see Table ).

At low temperature, ferritic stainless steel pipe has low-temperature brittleness like carbon steel, but austenitic steel does not. Therefore ferritic or martensitic stainless steel produces low-temperature brittleness, while austenitic stainless steel or nickel base alloy does not show low-temperature brittleness. Sus (Cr) and SUS (cr) of ferritic stainless steel pipe It shows that the impact value decreases sharply at low temperature. Therefore, it is necessary to pay special attention when using at low temperature. As a way to improve the impact toughness of ferritic series stainless steel, high purification process can be considered. With the help of C and N level, the embrittlement temperature is in the range of - ℃ to - ℃Theoretical weight of stainless steel pipe: w = outer diameter - wall thickness x wall thickness x..Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry.production,Ferritic stainless steel the Cr content of ferritic stainless steel is generally % ~ %, and the carbon content is less than .%. Other alloying elements are sometimes added. The metallographic structure is mainly ferrite, and there is no & alpha during heating and cooling=& amp; amp; gt;& gamma; The transformation cannot be strengthened by heat treatment. Strong oxidation resistance. At the same time, it also has good hot workability and certain cold workability. Ferritic stainless steel is mainly used to make components with high corrosion resistance and low strength requirements. It is widely used in manufacturing equipment such as production, nitrogen fertilizer and chemical pipelines.Vickers hardness stainless steel pipe Vickers hardness test is also an indentation test, which can be used to determine the hardness of very thin metal materials and surface layers. It has the main advantages of Brinell and Rockwell methods and overcomes their basic disadvantages, but it is not as simple as Rockwell method. Vickers method is rarely used in steel pipe standards.Human factors are also one of the causes of product oxidation that some consumers often encounter when using stainless steel products. Some consumers operate improperly in product use and maintenance, especially some stainless steel pipe products used in food and chemical equipment industry. For the artificially generated oxidation of steel products, they should have correct product use knowledge and Reasonable and effective maintenance shall be carried out regularly to reduce oxidation caused by improper use.

Some reasons for product composition ratio: in order to reduce the production cost reduce the proportion content of some important elements such as chromium and nickel, and increase the content of other elements such as carbon. This production phenomenon that the composition ratio is not strictly in accordance with the product model and product characteristics not only greatly reduces the product quality, for example,JiguaniStainless steel seamless coil, when the chromium content of stainless steel pipe is insufficient, it not only affects the production The corrosion resistance and formability of products have potential product quality and safety hazards when they are used in chemical, equipment and production industries. At the same time,The bright nickel layer on the stainless steel pipe is a silver white metal with slight yellow light. Its hardness is higher than that of copper, zinc, tin cadmium, gold and silver, but lower than that of chromium and rhodium. Bright nickel has high chemical stability in air and good stability to alkali. Using Brightener on stainless steel pipe, bright nickel can be directly plated without polishing, so as to improve the hardness, wear resistance and leveling of the surface, make the appearance of stainless steel pipe consistent with other nickel plated parts, and avoid the corrosion of potential difference between stainless steel pipe and other bright nickel. After using bright nickel solution for a period of time, due to the of brightenerOrganic substances (such as melons and vegetables, noodle soup, phlegm, etc.) adhered to the surface of stainless steel constitute organic acids in the presence of water and oxygen. For a long time, the corrosion of organic acids on the metal surface.Formula for hydraulic test pressure of stainless steel welded pipe for weight calculation fluid (gbt-): where: P - test pressure MPa; R - stress, taking yield point of %, MPa; s - nominal wall thickness of steel pipe, mm; D - Nominal outer diameter of steel pipe, mm.Jiguani,. Raw material problem of stainless steel pipe. If the hardness is too low, it is not easy to polish (BQ is not good). If the hardness is too low, orange peel is easy to appear on the surface during deep drawing, which affects BQ performance. BQ with high hardness is relatively good.. Domestic wce cerium tungsten electrode is used for electrode data. The shape and diameter of the end of cerium tungsten electrode have a great impact on the fluctuation of welding process and weld formation.Good ductility, used for forming products. It can also be machined to harden rapidly. Good weldability. Wear resistance and fatigue strength are better than stainless steel.