It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Hamburg wangzbeck,: High-pressure water abrasive derusting. Using the impact of high-pressure water jets and abrasives to polish and remove rust on the screw elevator, the advantage is that the damage to the material is small, but the water has certain damage to the electronic equipment and it is suitable for the detachable type of screw elevator.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Vikindu,The wrong connection of the motor of the elevator When a coil, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Conscientiously write the special construction plan for installation and construction,Hamburg wangzbeckElevating cargo elevator, and make safety technical disclosures to the installers.

The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, or one of the parallel branches is disconnected, the three-phase current will be unbalanced and the motor will overheat.How to maintain the elevator in winter? One reason is also the primary reason. Many workers in other industries do not know that the hydraulic oil of hydraulic elevators is also used in summer and winter. freeze. After entering the low temperature in winter, you must remember to replace the hydraulic oil containing antifreeze in winter, which is suitable for operation at low temperature.Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, and pulleys are made of solid materials to ensure safety.Promise and keep promise, and can also be customized according to user requirements, with a load of up to tons.The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.Mechanisms: Mechanisms such as tabletops, track grooves wire ropes, chains, and pulleys are made of solid materials to ensure safety.

Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.consumption,In the construction elevator the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.Avoid, especially during storage. Store in a cool,Hamburg wangzbeckGood comments on cargo elevators, dry place, and avoid rain and snow during work.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Hamburg wangzbeck,Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose,Hamburg wangzbeckFixed hydraulic lifting cargo elevator, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.Test the freight elevator every day to see if the freight elevator can operate normally.The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.