The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.　　The disc friction loss of the slurry pump impeller will decrease with the decrease of the impeller diameter, so that the pump efficiency of most low specific speed pumps will improve slightly after the impeller is cut. After cutting, keep the blades overlapped to a certain extent, and the degree of blade overlap will decrease with the addition of specific speedMars,　　The submersible sewage pump operates under water. Compared with other motors, the working environment is poor. Regular inspection and maintenance are essential to ensure the 'health and longevity' of submersible sewage pumps!　　Limited. According to relevant materials, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut, the flow area in the pump body increases, which makes the flow increase after the impeller is cut.Surinam,　　 the front and rear bearing glands are equipped with oil seals,MarsZD slurry pump, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.　　The development of submersible slurry pump is to adapt to increasingly complex working conditions facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pump　　As a submersible slurry pump widely used in many fields, it has the advantages of simple structure, convenient disassembly and maintenance,MarsAh slurry pump, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged, and the service life of the bearing has also been greatly changed.

　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　 After the electric pump has been used for many times, it is necessary to put the electric pump into clean water and run it for several minutes to prevent sediment in the pump and ensure the cleanness of the electric pump.　　Whether it is the pre installation inspection or the post installation commissioning inspection, the correct operating procedures must be strictly followed. Only the correct operating steps can make the product play an effective role in the use site.Test results,　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.

　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.Meticulous workmanship,　　The use of water pumps is related to all aspects of our life. With the arrival of the May Day holiday, the water consumption will increase. Therefore it is necessary for us to choose a suitable water pump.　　 Professional maintenance: if the submersible sewage pump cannot work normally, do not disassemble and repair it without authorization, but carry out professional maintenance immediately.　　First, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor, the motor is only in local placesMars,　　It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipment　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, so the wear resistance of the pipeline should also be considered.