Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.Tour,Check whether the self-locking device of the differential protector is normal before working at heights.This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.Tororo,The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Outriggers: mechanical outriggers, ordinary hand-operated outriggers, pull-out outriggers.Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.

If the motor of the hydraulic lift is overheated stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.Open the package prematurely. Before installing the elevator bearing, do not open the package in advance. This will easily lead to premature pollution of the bearing. These pollutions will cause premature damage to the bearing. In addition, ensure the installation The environment is clean, do not bring iron filings, dust,Tour3 ton lifting cargo elevator, dust, etc. into the bearings, because even some small dust will affect the running-in between the bearings for a long time, resulting in a decrease in the life of the elevator .The last thing to note is that, compared with the lifting platforms in some places, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce,TourOutdoor lifting cargo elevator, install, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.Supply chain quality management,The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.When installing dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.

Secondly, there must be no dirt on the friction surface. If there is dirt, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.Credit guarantee,After the goods are transported, clean up the debris on the platform.Good stability: The overflow valve can prevent the system pressure from being too high during upward movement. Emergency manual valve: In case of power failure, the car can be emergency lowered to the nearest floor to open the door. Manual pump: When the system fails, the manual pump can be operated to pump out high-pressure oil to raise the car to the nearest floor; Oil tank oil temperature protection: When the oil temperature in the oil tank exceeds the standard setting value, the oil temperature protection device will send out a signal, Suspend the use of the elevator, and start the elevator when the oil temperature drops.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.TourSafety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters and the maximum load is about tons. .Are the water cooling and air cooling of the hydraulic station the same?Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, the door the outer edge of the wheel hub,TourGuide rail type lifting cargo elevator, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.