Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is more　　If the pump outputs more medium liquid, it will certainly do more work. If it sends less water, it will certainly do less work,　　 hydrogen sulfide gas content mg/l　　What is the order.Embu,　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking,Kifar JonahRubber lining submerged slurry pump, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumping

　　 Another possibility is that the gas is sucked in when the pump is in use.　　It is worth noting that the QW mobile type is generally used without a fixed position, so it is usually used temporarily without an electric control cabinet, and a special person is required to control the shutdown of the water pump.　　How to avoid this situation when the equipment is in use.Where to sell API,　　After meters,Kifar JonahSplit vertical pipeline pump, the sealing of the equipment can not bear the water pressure at this depth.　　The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned.　　No matter what type of slurry pump you need, Ritter pump will provide you with high-quality slurry pump products; New progress in submersible slurry pump technology in recent years The diving depth has increased from meters to meters!

　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, otherwise the motor will fall into the waterknowledge,　　It is located in the middle, so it seems that many regions have good effects when using it.　　 Use a V insulation resistance meter to measure the insulation resistance between phases and phase to ground of the electric pump motor, and the value shall not be less than m Ω. Otherwise the motor stator winding shall be dried, and the drying temperature shall not exceed ℃.　　 there is also a simple method to measure the vibration frequency of the pump by vibration method. However, when using one method, there are other vibration sources that will affect the measurement results. Therefore, in fact,Kifar JonahVortex pump and pipeline pump, it is mainlyKifar Jonah,　　As a submersible slurry pump widely used in many fields it has the advantages of simple structure, convenient disassembly and maintenance, and convenient installation and use. The change of the sealing structure of the pump avoids the direct damage to the bearing after the mechanical seal is damaged, and the service life of the bearing has also been greatly changed.　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s.　　The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates.