The load of this series of products is divided into . to . tons,creteil Two ton lifting cargo elevator, and can also be customized according to user requirements, with a load of up to tons.Test the freight elevator every day to see if the freight elevator can operate normally.creteil ,The manufacturer adjusts the relief valve of the hydraulic lifting platform to the best state before delivery. If the customer adjusts it at will during use, the service life of the motor will be shortened; Especially in summer, pay attention to the heat dissipation of the hydraulic lifting platform during use. If the temperature is too high, it is easy to burn out the circuit; Do not underestimate these actions which can save you a lot of unnecessary after-sales.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches, small rocks on the driving tires, there may also be a peeling paint spot and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.Kazimad,Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.

Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so,creteil Enterprise elevator, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)The product has solid structure, large carrying capacity, stable lifting, simple and convenient installation and maintenance, and is an economical and practical ideal cargo transportation equipment for replacing elevators between low floors. The editor will tell you some common sense about its daily maintenance: when the outdoor elevator is maintained, and the elevator must be suspended to prevent the elevator from falling suddenly and causing casualties.Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .Excellent quality,Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.

The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod,creteil Five ton cargo elevator, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.technical service,The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.The manufacturer adjusts the relief valve of the hydraulic lifting platform to the best state before delivery. If the customer adjusts it at will during use, it will cause the internal pressure to fluctuate. In severe cases, the service life of the motor will be shortened; Especially in summer, pay attention to the heat dissipation of the hydraulic lifting platform during use. If the temperature is too high, it is easy to burn out the circuit; Do not underestimate these actions, which can save you a lot of unnecessary after-sales.Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, iron plate seal type.creteil ,Test the freight elevator every day to see if the freight elevator can operate normally.In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.