During the process, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, but in fact, we use it at ordinary times　　It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotatingTanjong Karang ,　　The submersible sewage pump is a kind of pump product which is connected with the motor and works under the water at the same time. Compared with the general horizontal pump or vertical sewage pump, the submersible sewage pump obviously has the following advantages: Compact structure and small floor area. Submersible sewage pump is submerged　　So it is called: submersible slurry pump.Curia, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump,Tanjong Karang Vertical centrifugal slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choice　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.　　In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it too

　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.　　Although they are both pipeline pumps among centrifugal pumps there are still many categories. Next, let&#;s talk about some models of pipeline pumps and their respective uses.　　When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flowsranking,　　Submersible pump is a common water lifting equipment for deep wells. During operation,Tanjong Karang ZD slurry pump, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, industrial cooling, farmland irrigation, seawater lifting, ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersible　　 selection of raw materials for flow passage parts: the raw materials for flow passage parts of the pump can be selected according to the particle composition, shape, hardness, concentration, acid, alkali and other characteristics of the transported materials.　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be

　　 selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.Manufacturing cost,　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.　　Control type Liquid level control: the control cabinet is equipped with a high-performance key float switch to automatically control the start and stop of the water supply and drainage pump according to the high and low changes of the liquid level.　　Carbon, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.Tanjong Karang 　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　During normal operation, the temperature of the motor is very high, some even as high as ℃. In this case,Tanjong Karang Fire deep well pump, it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, or　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer.