protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.When the freight elevator breaks down, professionals should be invited to repair it and the freight elevator cannot be altered without authorization.Lei Shufu,For the introduction to the daily maintenance of the elevator, the brakes of each organization should be regularly inspected and the distance between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. On the surface, there should be no dirt, and if there is dirt, it must be washed off with gasoline or thinner.Conscientiously write the special construction plan for installation and construction,Lei ShufuEnterprise elevator, and make safety technical disclosures to the installers.Tangier,What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.Prepare the foundation according to the foundation plan, leveling, and alignment to ensure the level of the foundation and various requirements for use.Are the water cooling and air cooling of the hydraulic station the same?

Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly, check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)It is forbidden to use hemp rope as a safety rope when using a mobile lift for high-altitude operations.Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.Sales Department,Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.

Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.Promotion,The price is guaranteed, the service is guaranteed, the quality and performance of the product must be good. Do not accept the products of some manufacturers whose quality is not up to standard, so as to avoid some safety hazards in use.Function: Convenient unloading, strong stability, low maintenance cost. It is suitable for various vehicles on the loading and unloading yard and places with relatively heavy traffic. Loading and unloading platform, lifting platform, unloading platform: Anti-slip device: This device is welded by steel plates, which can realize the anti-slip function efficiently and is reliable.Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.Lei ShufuThe anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed it can be realized. At the same time, the platform is level with the ground, does not occupy the ground space, and does not affect the passageway.Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .