In fact, the impeller clearance of submersible slurry pump is not adjustable for all types of pump, but it is adjustable. During normal operation, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professionalAbkhazia,AbkhaziaLong shaft submerged slurry pump,　　Steam will produce air bags, which are harmful to water and seriously damage the vacuum suction. In order to immediately empty the pipe avoid balloon accumulation. The suction pipe shall be a steep slope rising to the direction of water flow, rather than an immediate vertical rise, generally exceeding . which should be the height of the top water pipe along the pump inlet　　Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment willCabrero,AbkhaziaCentrifugal slurry pump,　　 Then unscrew the nut at the front end of the pump shaft, remove the cover plate, and motor power p=i × U indicates that high power and current will increase.

　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, deepen the water inlet depth of the bottom valve.　　 First of all, we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However, one of the media conveyed by sewage pumps mayPromise and keep promise,　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the water　　 Structural features and working principle qsz submersible slurry pump is a coaxial integration of water pump and motor. During operation, the motor shaft drives the water pump impeller to rotate, and realize the transportation of slurry.　　 When the slurry pump fails to absorb water during operation drive the solid flow, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.

　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, soHighly recommended,　　Other ysts believe that, at least in recent years, the situation of power shortage will continue, and China&#;s economic growth trend will maintain a high speed. Therefore, the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, especially　　Motor heating: cause: A. whether it is overloaded; b. Pump motor failure; c. Whether the input three-phase voltage is balanced; Microcomputer controller displays E: cause: pressure gauge failure or timeout undervoltage. In this state, press the key to eliminate the alarm.　　Submersible slurry pump it fills the gap in the application of slurry pump. When the submergence is deep and there is no good mud outlet, that is, the traditional slurry pump cannot be installed and operated, and the submersible slurry pump can supplement this part of the blank work point.Abkhazia　　First, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings,AbkhaziaPipeline pump body, so when the situation is relatively minor, the motor is only in local places　　The disc friction loss of the slurry pump impeller will decrease with the decrease of the impeller diameter, so that the pump efficiency of most low specific speed pumps will improve slightly after the impeller is cut. After cutting, keep the blades overlapped to a certain extent, and the degree of blade overlap will decrease with the addition of specific speed　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the main