When it is used for ground heating and hot spring transportation, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.The wear resistance, fracture toughness, impact toughness and bending strength under different process conditions were compared, and then the heat treatment process of GCrMo was determined. Development and application of ZYS- bearing damping and antirust oil. Bearing is a new type of multial damping and antirust oil. It takes refined mineral oil as the base oil and is equipped with various additives such as antirust and antifriction. Through comparison test, matching test with lubricating grease and user test, it is proved that ZYS- bearing damping and antirust oil has outstanding damping effect and good antirust lubrication performance.nagual ,Straight seam welding is adopted for larger diameter welded pipe, and spiral welding is mostly adopted for large diameter welded pipe; According to the top appearance of seamless steel pipe, it is divided into annular welded pipe and special-shaped (square, etc.); according to different materials and main purposes, it is divided into mining anti liquid transportation welded steel pipe, hot-dip galvanized welded steel pipe for bottom pressure liquid transportation continuous conveyor idler electric welded steel pipe, etc. it is arranged from small to large according to diameter * wall thickness according to the specification, model and dimension table in the current standard.I-beam: national standard * what is the wall thickness of I-beamCoronia del Sacramento,All the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape. H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam, with large lateral stiffness and strong bending resistance. Under the same specification, H-beam is lighter than I-beam.Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.

Cross rolling pass system. This pass system refers to that the two open legs of the I-beam pass are not on the same side of the waist at the same time, and the waist has an included angle with the horizontal axis.The smooth of steel pipe is mainly through tension reducing, which is a continuous rolling process of hollow base metal without center and tip. Under the condition of ensuring the capillary welding quality, the whole welded pipe is heated to more than ℃ by the welded pipe tension reduction process, and then rolled to finished pipes with various outer diameters and wall thicknesses by the tension reduction machine ( times in total). The fluid pipes produced by developed countries in the world have adopted the welded pipe smooth process in a large number of boiler pipes. With the development of society, Domestic hot welded pipe has gradually formed a situation to replace smooth pipe.Key technical characteristics of alloy pipeCredit guarantee,Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different,nagual How much is 75 welded pipe per meter,nagual I-beam price quoted today, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.

What is the purpose of flat steelHonest management,The specification of I-beam is expressed in cm of waist width. For example the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, expressed as No. ~ No., and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.According to the shape of the product, special flour, welding or ordinary thread connection shall be used.C - section steel is reliable and stable in stress, can be accurately positioned, and is resistant to impact and vibration Moreover, it has good versatility and combination, and has a variety of C-section steel and size selection to ensure its flexibilitynagual , Hot push hole diameter. More sensitive applications and facilities of such methods require simplicity, low cost, easy maintenance durable economic development and convenient product specification transformation. For example, the production of large diameter must be grooved pipe, elbow and similar products. You only need to add some spare parts. The expansion method of hot push can be used to process and manufacture large-diameter, thick wall and thin alloy steel pipes, and can not exceed the working capacity of thick wall pipes of machinery and equipment.Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.Metallization: refers to the process of penetrating metal atoms into the surface layer of alloy steel pipe. It is to alloy the surface layer of steel so that the workpiece surface has the characteristics of some alloy steel. Aluminizing, chromizing, boronizing, siliconizing and so on are commonly used in production.