and the air pressure and air volume are relatively small, so the heat cannot be dissipated.　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.Kawasaki,　　For the pipeline pump in the workshop, it is necessary to consider whether the pipeline pump is worn to a certain extent due to inadequate maintenance, but the performance of the pipeline pump is degraded. In case of abnormal water absorption during installation check the motor during installation, and check the motor wiring and speed,　　The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned.Kayan,　　Submersible slurry pump Use ultrasonic method to detect whether there is cavitation in the submersible slurry pump. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps often have better measurement results when in use.　　It is also necessary to clean the ventilation duct to avoid blockage.　　In this way, a smooth surface can be formed on the surface.

　　It is also necessary to clean the ventilation duct to avoid blockage.　　Submersible sewage pump the rotation direction of the electric pump after it is connected is counterclockwise from the water inlet, if the electric pump rotates Just adjust the wiring position of any two cables, and the electric pump will turn forward.　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.Installation material list,　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.　　No matter what type of slurry pump you need,KawasakiVertical centrifugal slurry pump, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　During adjustment, firstly loosen the support cover, and then loosen the bearing seat. After adjusting the screw tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation

　　A large amount of lubricating oil is stored.Application process,　　The submersible slurry pump may be blocked when it is used at ordinary times. In particular,KawasakiIrrigation deep well pump,KawasakiUsed pipeline pump, some equipment is frequently used at ordinary times, but the maintenance work is not done well when it is used, so it will be blocked after being used for a period of time　　 It is not allowed to operate the electric pump at high lift for a long time, and try to control it within the range of the proposed use lift, so as to prevent the electric pump from burning out the motor due to overload.　　The disc friction loss of the slurry pump impeller will decrease with the decrease of the impeller diameter, so that the pump efficiency of most low specific speed pumps will improve slightly after the impeller is cut. After cutting, keep the blades overlapped to a certain extent, and the degree of blade overlap will decrease with the addition of specific speedKawasaki,　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate, the repair is timely, the repair personnel should regularly repair the bearing components check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and write　　The structure of the submersible slurry pump will be more intuitive. First, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speed　　For example, concentrate and tailings are treated in the concentrator, ash and slag are removed from the power plant, slime and dense medium coal are transported in the coal preparation plant, and slurry is transported in coastal river mining operations. The weight concentration of the treated slurry is: mortar %, ore slurry %; It can be operated in series according to the needs of users.