Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)zhen'an ,Boarding bridges are divided into mobile boarding bridges andBrief introduction of application range and mobile boarding bridge: high-priced elevator factory of various specifications welcomes waste dealers, industrial companies, enterprises, and power departments to visit and negotiate with the company! It is used in places where there is no loading and unloading platform on site or where mobile loading and unloading of goods is required. If there is no loading and unloading platform at the logistics site, as a remedial measure, the mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a mobile steel-structured slope, and the forklift can also directly drive into the truck compartment for batch loading and unloading operations. . Quick loading and unloading of goods can be realized with only one person operation and no power supply required.In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present,It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.Before using the aerial work platform, it is necessary to confirm whether the outriggers are well supported, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.

Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.The condition of the oil in each system of the elevator should be checked, and if it is found that the oil is foaming or turbid, it should be replaced in time. The performance of the professional elevator factory is stable,zhen'an Five ton cargo elevator, safe, reliable, and can be maintenance-free. The technical level has reached the domestic level and the international advanced level of similar products.The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation,zhen'an 4-ton cargo elevator, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.ranking,Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies,zhen'an Electric cargo elevator, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.

Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Total quality assurance,Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.When using a helmet, the helmet should be tightened and worn straight, and the strap of the helmet should be tied under the jaw and tightened.Are the water cooling and air cooling of the hydraulic station the same?zhen'an ,The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the feeding of the installed machine at a high place, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods car lifting, fixed three-dimensional parking and other places.Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.