First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs,SamoraCarbon steel explosion-proof pipeline pump, so it is a good choice　　 important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.Samora,　　Note: Motors for special environment can be customized according to the contract.　　 bind the exposed copper wire to the cable core evenly, heat it with an electric iron,　　Troubleshooting: first increase the water pressure, then inject water into the pump body, and then start the pump. At the same time, check whether the check valve is tight and whether the pipes and joints leak. If air leakage is found, apply lubricating oil or mixed paint on the joint after disassembly,SamoraIrrigation deep well pump, and tighten the screws.　　 The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!　　Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, the service life of slurry pump in this section is generally low. Of course, different minerals, abrasion

　　 in addition,SamoraSubmersible sewage pump, the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise, so in fact, such measurement is not very accurate.　　In order to meet the use requirements of slurry pumps in different industrial fields and working conditions, we have continuously carried out research, development and improvement, so that we have different series, each series has a variety of specifications and models and different series of products have different performance and s. Let&#;s learn about it below　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pumpquery　　If the water leakage is serious, the broken pipe shall be dismantled and replaced. Lower the lift and press the nozzle of the water pump into the water for .m.　　The type selection planning of submersible slurry pump has a great impact on its service life and operation stability. A scientific and reasonable type selection plan will affect whether the slurry pump can achieve efficient operation. The operating power of the slurry pump is very high and the loss is small. Service life of flow passage parts of pump　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certain

　　Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced, which maximizes the reliable operation of the mechanical seal and greatly extends its service lifeFinance Department,　　Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced which maximizes the reliable operation of the mechanical seal and greatly extends its service life　　Correct the main shaft of the water pump and adjust the position of the water pump and the motor relatively.　　Rate loss, so shaft power = effective power + lost power.Samora,　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, so　　Pump. In addition, the submersible slurry pump is mainly characterized by 'slurry', it can only be opened or closed, and the action time when opening and closing is relatively short.