I'll give you a detailed introduction to the heating technology of the lower tubes.For gas transmission: gas

There are many processing technologies for square tubes. I won't introduce the specific processing technology here. We only know about the processing technology of each other's tubes. We may have insufficient understanding of its heating technology. Next, steam and liquefied petroleum gas.Alvarden,Functional index analysis of square tube - commonly used are square tube Brinell angle (HB), Rockwell angle (hrahrbhrc) and Vickers angle (HV) Equal angle is a gauge needle to weigh the soft and hard level of metal data. In the current life, the angle method is rarely used to determine the angle. It uses the indenter with a certain number and shape to determine the angle value of the metal data surface being tested under a certain load according to the level.The second is to clean the surface of the opposite pipe. When cleaning the opposite pipe, the surface should be cleaned with solvent or emulsion. Square pipes of various specifications, square rectangular pipes, seamless square pipes, galvanized square pipes, galvanized pipes are supplied in time and cost-effective. They have become the preferred brand of many wire products. Welcome to buy! It is used to remove oil and dust. It is only suitable for removing grease and dust on the surface of square pipe, which can not remove rust and oxide scale. Therefore, it can only be used as an auxiliary means in production.Amatitlan,Plasticity QB square plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.High pressure oil pipe for diesel engine (gb-) is a cold drawn square pipe for high pressure pipe of diesel engine system.Tool derusting mainly uses tools such as steel wire brush to polish the surface of square pipe, which can remove loose or oxidized scale, rust, welding slag, etc. The derusting of manual tools can reach grade SA and that of power tools can reach grade SA. If the square pipe surface is firmly attached with iron oxide scale, the derusting effect of tools is not ideal and can not reach the anchor depth required by construction.

At this time, if the welding wire of the same material is used for spot welding where the thickness is insufficient, it shall be welded to the fixed thickness,AlvardenQuotation for galvanized 20 square pipe, ground and sandblasted, and repair welding shall be adopted where there are cracks, even if the steel pipe with another large opening can be made up at one time.Performance index analysis of square tube - hardness is an indicator to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.B. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.Welcome to inquire, ethylene, phenolic and other coatings commonly used for square pipes, the surface of square pipes is generally required to reach near white grade (SA). Practice has proved that almost all oxide scale, rust and other dirt can be removed by using this derusting grade, and the depth of anchor grain can reach ~ & mu; m,AlvardenHow much is a galvanized pipe, which fully meets the requirements of adhesion between layer and square pipe The shot derusting process can meet the technical conditions of near white level (SA) with low operation cost and stable and reliable quality.The reason why it is divided into two types is that chemical cleaning can only clean the surface very thoroughly, and it is difficult to achieve the desired results in some fine cracks.Carbon steel classified by chemical composition: square tube A. low carbon steel (C & le; .%); b. Medium carbon steel (C & le; . ~ .%); c. High carbon steel (C & le; .%).

Section shape classification of large-diameter qb square tube square tube is classified according to section shape: simple section square tube & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Flower shaped square pipe, open square pipe, corrugated square pipe, special-shaped square pipe, large-diameter qb square pipe surface treatment classification square pipe is divided according to surface treatment: hot-dip galvanized square pipe, electro galvanized square pipe, oil coated square pipe, machine tool equipment, machinery industry,AlvardenGalvanized square pipe 150, chemical industry steel structure, shipbuilding, automobile, steel beam and column, special purpose, large-diameter qb square tube wall thickness classification, large-diameter qb square tube according to wall thickness Classification & mdash& mdash; Super large diameter qb square pipe large diameter qb square pipe and thin-wall large diameter qb square pipe rectangular pipe are the names of square pipe and QB square pipe, that is, steel pipe with equal side length. It is made of rolled strip steel after process treatment. Generally, leveled, crimped and welded to form a round pipe, then rolled into a square pipe from the round pipe, and then cut into the required length. Usually pieces per bag. Qb square pipe, also known as square and rectangular cold-formed hollow section steel, is referred to as square pipe and rectangular pipe, code f and j respectively. The allowable deviation of wall thickness of qb square pipe shall not exceed plus or minus % of nominal wall thickness when the wall thickness is not greater than mm, plus or minus % of wall thickness when the wall thickness is greater than mm, except for the wall thickness of corner and welding joint area.Excellent quality,Structural stainless steel square pipe (gbt-) is a hot-rolled (extruded, expanded) and cold drawn (rolled) square pipe made of stainless steel for corrosion-resistant pipes, structural parts and parts widely used in chemical, petroleum, light textile, food, machinery and other industries.Square tube is the main type of square tube. It is also very popular in the square tube market. There are many people doing this kind of thing, so there are many in the competition. The future market potential is huge. We should grasp this information well. In addition, we must learn about relevant maintenance and repair!Square tube has a wide range of application fields. Its main field is the construction industry, which promotes the development of economic construction. Because the production process of square tube hole is different, the production design of square tube hole is also different. Next, I will introduce in detail the types of tube hole design below.AlvardenB. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.Impact toughness the load acting on the machine part at a great speed by QB is called impact load, and the ability of metal under impact load is called impact toughness.Pull square tube: