Stages needing attention in the production and manufacture of alloy tubesIn order to make the steel pipe workpiece have the required mechanical, physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.Duvich,External steel bonding reinforcement method is a more traditional reinforcement method. The utility model uses an adhesive to paste the steel plate or reinforcement mesh on the cracked part of the wall to achieve the purpose of reinforcement. The commonly used adhesive is usually epoxy resin. This method is simple and fast in construction and has little impact on production and life. Basically, the bearing capacity of the wall can be greatly improved without changing the shape and internal use space of the components. It is mainly applicable to the reinforcement of walls that do not allow to increase the section size of original components, but can greatly increase the section bearing capacity.The shape of I-beam is similar to that of H-beam. What is the difference between them?Samarinda, Miscellaneous scabAfter determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.The section of I-beam has good straight pressure and tensile resistance, but the section size cannot resist torsion because the wing plate is too narrow. On the contrary, H steel has its own advantages and disadvantages.

Small longitudinal crackPackaging: Welding nets are generally packaged in paper (mostly gray white, yellow,DuvichHow much is a ton of straight welded pipe, etc.), some similar to welding wire diameter welding nets, agriculture, construction, transportation, mining and other industries. Such as machine shields, animal fences, flower and tree fences, window fences aisle fences, poultry cages,DuvichCustom welded pipe, baskets and decorations.The shape of small longitudinal crack on the surface of alloy pipe is less than mm The overall width is less than mm The depth is lower than .mm.Good quality,After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.After isothermal quenching treatment, the modified LNs steel of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment.Because all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance, cost saving and light structural weight in all directions, and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, so it is named parallel flange I-beam. The web thickness of I-beam is smaller than that of ordinary I-beam with the same height of web, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.

The pickling agent in the pickling process contains many acidic substances, including hydrochloric acid, etc., which has strong corrosion and reduction, and the temperature of etching substances is relatively high. Therefore the corrosion resistance of alloy pipes is specified higher.Direct labor,Alloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.Generally what are the customer&#;s requirements and standards during acceptance? When the galvanized pipe is accepted, you can judge whether it is qualified from the appearance, or whether there are problems such as missing plating or bubbles on the outer wall of the whole square pipe. Only by solving these problems in time can it be judged as qualified and better used.The specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, expressed as No. ~ No. and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Duvich,At present, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.The core of C-section steel is the structural system of braced frame. More than half of such senior managers in China are the former. Unfavorable to earthquake resistance. Hydraulic power, and the power is large, generally about KW, which is similar to the plate shearing and bending machine. The general control process is complex, and PLC control is mostly used.