Performance parameters and application scope of I-beamWhen selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties,Santa Catalina iktahuakenCustom welded pipe manufacturer, chemical properties, weldability and structural size.Santa Catalina iktahuaken,Oxygen blowing welded pipe: it is used as steel blowing pipe. Generally, small-diameter welded steel pipe is used. There are eight standards from / inch to inch. Made of , , ,Santa Catalina iktahuakenHow much is the price of I-beam per meter, or q-q steel strip. In order to prevent corrosion, some are aluminized.Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main axes of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Dongguan City,I-beam, also known as universal beam, is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape. Remove defective pipes within the allowable length.The delivery length of I-beam is divided into fixed length and double length, and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into -, - and - according to different specification numbers. The length selection range of imported I-beam is generally -.

The section of I-beam has good straight pressure and tensile resistance, but the section size cannot resist torsion because the wing plate is too narrow. On the contrary, H steel has its own advantages and disadvantages.In addition, galvanized steel is more expensive than ordinary steel pipes, the more serious the disadvantages.Home page recommendation, The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.The delivery length of I-beam is divided into fixed length and double length, - and - according to different specification numbers. The length selection range of imported I-beam is generally -. Hot push hole diameter. More sensitive applications and facilities of such methods require simplicity, low cost, easy maintenance, durable economic development and convenient product specification transformation. For example, the production of large diameter must be grooved pipe, elbow and similar products. You only need to add some spare parts. The expansion method of hot push can be used to process and manufacture large-diameter, thick wall and thin alloy steel pipes, and can not exceed the working capacity of thick wall pipes of machinery and equipment.

Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment,Santa Catalina iktahuakenHow much is a 2-inch galvanized pipe, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, meet the requirements of thermal insulation and cold protection, reduce heating equipment unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.Safety production,Performance parameters and application scope of I-beam When the mesh reinforcement on both sides of the beam is different, the reinforcement on both sides extends into the beam, and the reinforcement anchorage length is required.I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill,Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main sleeves of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Defects of alloy pipe and solutions:a. In the forming process, the thick steel plate has uniform deformation, small internal stress and no scratch on the surface. The alloy pipe produced and processed has higher coordination ability in the scope of size specification and model of diameter and wall thickness, especially in the production and manufacturing of steel structure design grade thick wall pipe, especially medium diameter small thick wall pipe, which has incomparable advantages of other processing technologies, and can meet a large number of customer regulations on the specification and model of alloy pipe.