KatriniQJ submersible pumpDoes deformation affect the effect
release time:2023-05-12 06:01:13

   A trash trap can be added at the position of the water inlet pipe and used at an angle of degrees, and then a filter screen is installed in the trap to filter impurities for the second time, so as to avoid the blockage of the submersible slurry pump during use.  Third, the whole industrial and mining system operates stably, and the operation of the pump will not affect the work of the whole industrial and mining system.Katrini,  Finally, select the appropriate pump model according to the determined Q and H. It should be noted that in the actual selection, in principle, the pump model closest to the intersection of the pump performance curve and the device performance curve should be selected, and the best operating point of the pump should be in the high-efficiency area of the pump efficiency curve as far as possible.  Second, the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so IMesa, the power supply across the country has been tense again which has driven the hot sale of it and generators in the phase II market. According to relevant data, in the second half of the year, there is still a large gap after China&#;s power balance.  During adjustment, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operation  In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without its


KatriniQJ submersible pumpDoes deformation affect the effect



  Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.   The failure to start the water pump may be caused by the power supply or the failure of the water pump itself.   Before starting the submersible slurry pump,KatriniVertical heavy-duty slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.index,  The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent  After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started, the outlet valve of the final stage pump can be gradually opened. The speed of opening the valve should be controlled by the fact that the pump does not vibrate and the motor of any stage does not exceed the rated current.  The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump,KatriniRubber lining submerged slurry pump, high automation and performance


KatriniQJ submersible pumpDoes deformation affect the effect



  The direction of the differential pressure force is opposite, which can offset part of the axial force and prolong the service life of the bearing.Equipment maintenance,  Although the shaft seal occupies a small position in the pump, so that the gas can be discharged from the discharge port. Secondly the discharge valve must be opened to start the self-priming pump, there should be enough liquid in the cavity of the self-priming pump, otherwise it will not   important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.Katrini,   First,KatriniWQ submersible pump parameters, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section stuffing box body and bearing body; Then screw off the round nut on the shaft, and successively install the bearing inner race, bearing gland and retaining sleeve  The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pump  So it is called: submersible slurry pump.

comment list
  • FRP production equipment

    KatriniQJ submersible pump The quality is very good, I bought it for the second time, the goods are good, the boss is very good

  • Design of Traction Drive and Control System for Rail Transit

    It is still affordable to buy things online, KatriniQJ submersible pump I signed for two days late, but the things are really good, and the boss is good. The speed of transportation is also very fast.

  • County shuttle bus

    The boss is so kind, he really knows his job well. Under your guidance, I will soon become an expert! The seller's service is really attentive. Bring colleagues together in the future. Very good Katri

  • Qiu Juetong

    The quality is very good, exactly the same as the seller’s description, very satisfied, really like it, completely exceeding expectations, the delivery speed is very fast, the packaging is very carefu

©2009-2024Metal Microblog  Sitemap