Xanthe Pipeline pump bodyApplicable manuals and methods for installation
release time:2023-05-12 12:49:19

  Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment, and the current will slowly increase during use. Well, we should choose  When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise,  The inner wall is corroded and the outside air is sucked in. The pipeline pump packing is worn or the packing is not compacted.  The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.Rio Bueno, the diameter of the impeller after cutting shall not be less than % of the diameter of the standard impeller, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut, the flow area in the pump body increases, which makes the flow increase after the impeller is cut.  Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant,Xanthe HH slurry pump, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.   If the power cord is not well contacted, it will also lead to the burning of the motor.


Xanthe Pipeline pump bodyApplicable manuals and methods for installation



  Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.  Slide until the active coupling is in place. When mobile equipment is selected, the hose shall be sleeved first, it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.quality,  When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium so that  Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment.   Next,Xanthe Water well pipeline pump, you can place abrasive cloth on the glass or dry wood it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However if the thrust rubber water seal is used, when


Xanthe Pipeline pump bodyApplicable manuals and methods for installation



   Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.Welcome to inquire,  There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media,Xanthe Sewage pump diving, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.   No maintenance: if it is not used continuously after startup, the submersible pump will rust and cannot be started. If it is not used for a long time, do not immerse it in water for a long time. Put it into clean water and run it for a few minutes to clean the mud inside and outside the pump.  What should be paid attention to in the process? Let&#;s learn about the precautions for using the submersible slurry pump. When the equipment is in use, the pump itself generally needs to be placed on land for use, but its suction pipe needs to be placed in waterXanthe ,   First remove the pump from the engine.  The purpose is to avoid water leakage of the pump, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.  Water flow into the bearing damages the bearing.

comment list
  • Packaging Machinery

    I just received it in the morning and my friends like it very much. I will buy it from you next time Xanthe Pipeline pump body.

  • Environmental Pollution Prevention and Control

    I just received it this morning and I like it very much. I'll come next time, can you introduce a friend to buy Xanthe Pipeline pump body for a discount?

  • Excellent Alliance Assets

    Xanthe Pipeline pump body Not bad, the price is worth it, just right.

  • Stone Printing Company

    Support each other! Seeing you Xanthe Pipeline pump body, we are preparing to place an order and hope to ship on time.

  • Bearing Manufacturing

    Xanthe Pipeline pump body The quality is not bad, and the goods are delivered in time. I recommend you to buy it next time.

  • Fengda Dingye Technology Co., Ltd.

    Xanthe Pipeline pump body It can be said to be top-notch, and the details are perfect.

©2009-2024Metal Microblog  Sitemap