Application characteristics of I-beam: Judged as failing.Tanjung Balai,The smooth of steel pipe is mainly through tension reducing, which is a continuous rolling process of hollow base metal without center and tip. Under the condition of ensuring the capillary welding quality, the whole welded pipe is heated to more than ℃ by the welded pipe tension reduction process, and then rolled to finished pipes with various outer diameters and wall thicknesses by the tension reduction machine ( times in total). The fluid pipes produced by developed countries in the world have adopted the welded pipe smooth process in a large number of boiler pipes. With the development of society, Domestic hot welded pipe has gradually formed a situation to replace smooth pipe.X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water wastewater, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.Nicoya,Whether I-section steel is ordinary or light, due to the relatively high and narrow section size,Tanjung Balai12Cr2MoWVTiB alloy pipe,Tanjung BalaiPrice of 42CrMo seamless pipe, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.I-beam is mainly divided into ordinary I-beam, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -,Tanjung BalaiHow much is I-beam per meter, that is, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.

What is the purpose of flat steelThe reinforced concrete surface reinforcement method has the advantages of simple construction technology and strong adaptability, which can greatly improve the bearing capacity, flexural stiffness and ductility of the brick wall. At the same time, its natural frequency can be changed to improve its performance in normal use. It is mainly applicable to the solid wall, porous hollow brick wall and mm thick empty bucket brick wall with no cracks and shear in the original wall.I-beam, also known as steel beam is a long strip of steel with I-shaped section. I-beam is divided into ordinary I-beam and light I-beam. It is a section steel with I-type section shape.Home page recommendation,According to the theory of steel structure, that is, the I-beam should be standing rather than lying down.The key purpose of grinding and polishing alloy pipe is to moisten the surface, and the relevant limit accuracy or appearance change is not easy to change.Under the action of thermal stress, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate shape and chemical composition of the workpiece in the martensitic transformation zone.

Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.Quality inspection report,The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment, and the reproducibility of the solution is good. Steel mesh guardrail (steel mesh fence) steel mesh guardrail refers to the guardrail made of steel mesh. It is stronger and more durable than the guardrail made of electric welding mesh, hook mesh, etc., but its cost is much higher, and it is rarely used under normal circumstancesDue to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main sleeves of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Tanjung Balai,The utility model has the advantages that the axial force of the roll is small, the axial movement is small, the working inclined plane is not required, the pass occupies a small length of the roll body, and more passes can be matched under the condition of a certain length of the roll body.a. In the forming process the thick steel plate has uniform deformation, small internal stress and no scratch on the surface. The alloy pipe produced and processed has higher coordination ability in the scope of size, specification and model of diameter and wall thickness, especially in the production and manufacturing of steel structure design grade thick wall pipe especially medium diameter small thick wall pipe, which has incomparable advantages of other processing technologies, and can meet a large number of customer regulations on the specification and model of alloy pipe.At present, there is still a big gap in the production technology of C-section steel between China and foreign countries.