Heating surface pipes, economizers, superheaters, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)Some applications of I-beam:Cardenas, Ditch cover plate (ditch cover plate) is widely used in municipal roads, garden facilities, residential quarters, schools, stadium pipes and other places.a. In the forming process, the thick steel plate has uniform deformation, small internal stress and no scratch on the surface. The alloy pipe produced and processed has higher coordination ability in the scope of size, especially in the production and manufacturing of steel structure design grade thick wall pipe, which has incomparable advantages of other processing technologies,CardenasHow much is I-beam 160 per ton, and can meet a large number of customer regulations on the specification and model of alloy pipe.Gyal,Alloy pipe can be divided into round steel pipe and special-shaped steel according to different cross-sectional area. Because the circular area is large on the premise of the same side length, a large amount of liquid can be transported with an annular tube. In addition, when the circular cross section bears the internal or external axial working pressure the bearing force is more symmetrical. Therefore, most seamless steel pipes are round steel pipes.Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. Remove defective pipes within the allowable length.

The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages. Spiral seam submerged arc welded steel pipe for general low-pressure fluid transportation (SY / t- is a submerged arc welded steel pipe for general low-pressure fluid transportation such as water, gas, air and steam, which is made of hot-rolled steel strip coil as pipe blank, often warm spiral forming and double-sided active submerged arc welding or single-sided welding. Peak crackaverage method,I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, the corresponding height is -. At the same height, the light I-beam has narrow flange, thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.The shape of I-beam is similar to that of H-beam. What is the difference between them?Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.

Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal, eliminate structural defects, reduce strength improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Affordable price, Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded. Silicon; it can improve the hardness of steel, but the plasticity and toughness decrease. Electrical steel contains a certain amount of silicon, which can improve the soft magnetic propertiesIts heat sealing effect is remarkable. It can be directly buried immediately which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation,CardenasSoftware for turning reinforcement, prevent actual operation and maintenance,CardenasWhat is the price of steel bar shear line, meet the requirements of thermal insulation and cold protection, reduce heating equipment, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.Cardenas,I-beam is widely usedThe production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of - thickness of -, rectangular section and slightly pure edge. Flat steel can be finished steel or it can be used as blank for welded pipe and thin slab for laminated thin plate.Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.