The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.Helsinki,　　Finally, select the appropriate pump model according to the determined Q and H. It should be noted that in the actual selection, in principle, the pump model closest to the intersection of the pump performance curve and the device performance curve should be selected, we don&#;t know how to choose the pump when we buy it. In fact, we only need to choose the appropriate equipment according to our own use needs when we choose it. It&#;s more like that in a conventional family, when we use it, the flow is smallMachala,　　Many users including new practitioners of slurry pumps, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.　　Under the action of auxiliary devices, it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use

　　Stability and reliability of seals between pump bodies.　　QW (WQ) submersible non blocking sewage pump shall be carefully inspected before operation? Whether the cable is damaged whether the fastener is loose or dropped, and whether the pump is deformed or damaged during transportation,HelsinkiBooster pipeline pump, storage and equipment.　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.Inspection environment,　　Therefore, when the pump temperature is too high, you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it.　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.　　Under the action of auxiliary devices, it can transport the slurry, it can also ensure the internal and external balance of the submersible slurry pump during transportation, the cut impeller is usually used. The cut issupply,　　In fact, the impeller clearance of submersible slurry pump is not adjustable for all types of pump,HelsinkiCentrifugal slurry pump,HelsinkiVortex pump and pipeline pump, but it is adjustable. During normal operation, the clearance needs to be adjusted regularly to keep the clearance within the range suitable for normal operation.　　 No leakage protector is installed: leakage protector is also known as lifesaver. If the leakage value of the submersible sewage pump is higher than the working current value of the leakage preventer the leakage preventer will cut off the power supply of the submersible pump to ensure the normal operation of the equipment.　　The submersible slurry pump may be blocked when it is used at ordinary times. In particular, some equipment is frequently used at ordinary times, but the maintenance work is not done well when it is used, so it will be blocked after being used for a period of timeHelsinki,　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　 Next, the water seal, lock ring and other parts need to be installed.　　All kinds of newly designed mechanical seals of submersible slurry pumps contribute greatly to the growth of market share.