CeylonSelf priming slurry pump wholesaleHow to stand out at present
release time:2023-03-22 06:58:18

  After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started,CeylonVertical centrifugal slurry pump,CeylonDouble suction slurry pump, the outlet valve of the final stage pump can be gradually opened. The speed of opening the valve should be controlled by the fact that the pump does not vibrate and the motor of any stage does not exceed the rated current.   the submersible slag pump is often used to transport pulp containing solid particles, so the wear resistance of the pipeline should also be considered.Ceylon,   Change the oil: if the oil contains water drain it, change the oil, and then tighten the screw plug.  When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motorNamanyers,  The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall be  The submersible slurry pump is developed to adapt to the increasingly complex working conditions and facilitate the use of users. Its use mode is more flexible. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity,CeylonVortex pump and pipeline pump, excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.   the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer.


CeylonSelf priming slurry pump wholesaleHow to stand out at present



  We also need to limit the starting frequency and select appropriate thermal protection devices for use.   Gradually disassemble the outlet pipe, gate valve and elbow with installation tools, and tighten the next section of water pipe with pipe clamping plate. In this way, disassemble the pump section by section and lift the pump out of the well. (if it is found that there is a jam during the lifting and removal process, it cannot be lifted by force, left and right for safe lifting and removal)  Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves,  The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use   Prepare tools and materials: a set of metric box / open-end wrench bearing puller (commonly known as triangle puller), magnetic dial indicator, outside micrometer, caliper, feeler gauge, square ruler, copper bar, screwdriver with handle, hammer, V-shaped irons of the same specification, clean kerosene, oil basin, cotton yarn, etc.  Second, the service life of the flow passage parts of the pump is relatively long saving production costs.


CeylonSelf priming slurry pump wholesaleHow to stand out at present



  Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.ranking, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing, the service life of slurry pump in this section is generally low. Of course, different minerals, abrasion  (c) The minimum ambient air temperature is - ℃.   Impeller protection in order to ensure the operation of the submersible slurry pump, it is necessary to timely adjust the clearance between the impeller and the front guard plate. When adjusting the impeller clearance, first stop the pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts, make the bearing components move forward, and roll the shaft by hand to press theCeylon,  Therefore, the correct selection of shaft seal can ensure the safe and stable operation of slurry pump.  Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump, tighten the adjusting screw of the bearing box evenly, and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ, When δ= A (. ~ mm  As an emerging product, the submersible slurry pump has many advantages, especially filling the gap in the application conditions of the traditional horizontal and vertical slurry pumps. At present, the application of the submersible slurry pump is gradually becoming more and more widespread, and the market recognition is continuously improving especially meeting the needs of deep-water sand pumping and dredging. At present, the depth can reach meters.

comment list
  • Hao Qinghua

    The level of the seller MM is very high, and the people are very patient. I saw a lot of CeylonSelf priming slurry pump wholesale, but I feel that you have the strength and bought yours. I didn’t expe

  • Research and development of lost foam technology

    Buying things online is about integrity, and you do it! Thank you CeylonSelf priming slurry pump wholesale Like one Fast delivery, very good attitude, very satisfied! very good!

  • Li Tiezhu

    Can you give me CeylonSelf priming slurry pump wholesale detailed specification data?

  • plastic mold

    CeylonSelf priming slurry pump wholesale Very cost-effective! It is worth buying like everyone! worth having!

  • emerging energy companies

    I will buy it in the future CeylonSelf priming slurry pump wholesale and I will come to you again. Thank you boss and send a good comment. I love you boss. Thank you!

  • chemical fiber

    I really like it, I am very supportive, the quality is very good, exactly the same as described in CeylonSelf priming slurry pump wholesale, I am very satisfied, I really like it, completely exceed ex

©2009-2024Metal Microblog  Sitemap