The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.　　Promote the continuous expansion of the sales network group.Guiyang　　During daily use, we can observe, listen to and touch the submersible slurry pump according to the above methods, so as to judge whether there is a fault and the fault part of the slurry pump, and deal with it in time if any fault is found.　　Moreover, the leaked flammable, explosion and poisoning, and the consequences will be unimaginable.Mucumpiz,　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use　　Rate.　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.

　　Many users, including new practitioners of slurry pumps, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar,GuiyangDrilling fluid slurry pump, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?　　 Check the voltage to see if the voltage is too low to drive. Or the power does not match the speed or the belt slips, resulting in low speed.　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling, the motor temperature will rise, so it is easy to burn out the motor.Finance Department,　　Third, the whole industrial and mining system operates stably, and the operation of the pump will not affect the work of the whole industrial and mining system.　　The high-pressure water flows to the space occupied by the original bubble at a very high speed, the first thing we think of is water. Whether it is drinking water or coefficient water, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps,GuiyangSubmersible sewage pump, our basic survival is a problem.The cost is reasonable,　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness, which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possible　　 Determine the head h. After the flow is determined, determine the inlet and outlet pipe diameters of the pump, complete the layout of the whole pipeline, and determine the head. In the actual selection, the resistance coefficient of the pipeline is often too large. In addition when selecting the pump model, a head margin is added, resulting in　　Sex is different. Although the submersible slurry pump is widely used, the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact, the impurity pump dredging pump, etc. are all in the application scope of the slurry pumpGuiyang,　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.