Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal, etc.　　The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect the auxiliary impeller of the submersible slurry pump can also reduce the axial force.Bhiwandi ,　　The liquid level of slurry shall be higher than the inlet of pump.　　Other ysts believe that, at least in recent years, the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, especiallyCaruaru,　　Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment will　　 If there is abnormal sound inside the slurry pump and there is no water, it is likely that the equipment may have air infiltrating into it when absorbing water, which will cause abnormal sound inside the pump, and then at the same time, the impeller is damaged or the impeller is damaged　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certain

　　 drainage and water injection with vacuum equipment: the self exhaust of centrifugal pump is the same as the negative pressure exhaust of vacuum pump, so the water ring vacuum pump is used for exhaust to achieve the of water inlet.　　 estimated installation depth of pump M　　 If there is no corresponding water leakage sensor, it is necessary to regularly maintain the submersible slurry pump and replace the seals.ranking,　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand, the pump shaft should not be blocked under normal conditions. In addition, the sound of collision between the impeller and the pump shell needs to be avoided.　　 strip the outer layer of the cable to expose the copper wire for to mm, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally.　　 When starting the slurry pump, the outlet gate valve shall be (closed or slightly opened by /. Before starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor

　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth,　　Potential energy, pumping water up high. However once the pump can not absorb water, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?　　Environmental conditions for normal operation of ordinary YLB motor:　　Most of the time, we don&#;t know how to choose the pump when we buy it. In fact, we only need to choose the appropriate equipment according to our own use needs when we choose it. It&#;s more like that in a conventional family, when we use it, the flow is smallBhiwandi ,　　For example, in the market,Bhiwandi Used pipeline pump, for example, the sweeping pump, some of which have a depth of more than meters, it is not suitable to use a vertical slurry pump under such a working condition, but it is extremely easy to use a submersible slurry pump.　　 there is also a simple method to measure the vibration frequency of the pump by vibration method. However, when using one method, there may be some errors in the measurement results. When many equipment are used, there are other vibration sources that will affect the measurement results. Therefore, in fact, it is mainly　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pump