What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.Lexington Fayette,Mobile lift fault analysis mobileAnalysis of the mobile lift’s poor lift or weak lifting force: the pressure adjustment of the relief valve does not meet the requirements: adjust the pressure to the required value; the internal leakage of the oil cylinder: check or replace the oil cylinder assembly; the reversing valve is locked or internally leaked: check or exchange the valve assembly ;The oil level is too low, and the oil inlet filter is blocked: add enough oil and clean the oil filter. Fuel pump defective: check or replace pump.Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform,Lexington FayetteHydraulic guide rail type cargo elevator, which is mainly used in industrial plants, restaurants, restaurants, warehouses, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?Acoyapa,The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter, throttle valve, hydraulic control check valve, and balance valve so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted,Lexington FayetteTwo ton guide rail type cargo elevator, and the pressure gauge reads the pressure gauge.Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.Before the elevator manufacturer connects the motor to the elevator, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?

Nowadays, small and medium-sized enterprises are holding products with the idea of ​​good quality and favorable price.Regular inspection and maintenance, elimination of hidden dangers, and troubleshooting are all good for improving work efficiency, prolonging the service life of equipment and ensuring the safety performance of the elevator.Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, price advantage, quality guaranteed!Job description, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply and diesel engine.Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.

Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.query,The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.The development history and current situation of the scissor-type aerial work platform With the more and more widespread use of the vehicle-mounted aerial work platform in production, it has gradually been recognized by various industries and has begun to be applied to other industries with similar working environments. With the continuous expansion of the application range, some shortcomings have gradually been exposed in the process of use in some occasions. For example, its huge size is difficult to use in a small workplace, and the high-speed drive function cannot function in a small space. And if the hydraulic stabilizer configured on this old-fashioned vehicle-mounted platform fails, the equipment often cannot continue to be used. These limitations greatly reduce the working efficiency of the equipment. In order to meet the market demand, a new type of production level - self-propelled remote control aerial work platform came out in the middle and late s. From the birth of this new type of product, the field of aerial work platforms began to grow rapidly, and it was from then on that the global aerial work platforms began to develop in the direction of serialization. The structure and production process of this self-propelled remote-controlled aerial work platform are relatively simple, and a large number of improved aerial work platform products have entered the US market in large numbers. With the popularity of this product, some new contradictions have emerged. In some special occasions, such as gypsum technology, lead technology, live work, fire rescue and other fields, people urgently need a more compact and lightweight product. Driven by this demand, the scissor-type aerial work platform came into being. Due to the extensive use of electric design, the scissor-type aerial work platform can move freely in a small space, and can even be used on some fragile grounds and grounds with loads. At present, the demand for scissor-type aerial work platforms continues to rise. The proportion in the leasing industry has even reached %. Professional elevator factory and other products have a complete range of products, best-selling at home and abroad, advanced equipment, long service life! The product wire products are industry leaders, adjust the PCS system ring to align the side hole with the dust-proof hole,Lexington FayetteTwo ton lifting cargo elevator, and tighten the inner hexagon. After that remove the motor shaft key.Lexington Fayette,Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt it must be washed off with gasoline or thinner.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.