The combined platform is often used in small workshops with small volume of goods. However, it inevitably increases the distance of handling tools/vehicles in the workshop.The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within .MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.cork,Check valve leakage oil pipe check valve leakage. The solution is to carefully check whether the one-way valve is functioning properly. If it is not normal, it is recommended to replace the one-way valve with a new one.Protective device: In case of power or oil circuit failure, there should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)Rousse,Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.Volume speed control circuit: Speed control is achieved by adjusting the displacement of a variable pump or variable motor.The vibration range is proportional to the lifting height. The higher the height, the larger the shaking range, especially for mobile hydraulic cargo elevators. When the working height exceeds meters, the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection, increase stability, and reduce shaking.

The classification of lifting platforms is as follows: they are divided into mobile lifting platforms, automatic lifting platforms, hydraulic lifting platforms, folding arm lifting platforms, and sleeve type lifting platforms according to their different modes of movement.Therefore, maintaining the hydraulic cylinder is an important part of the entire hydraulic system maintenance. In addition, hydraulic cylinders are equivalent to the heart of the hydraulic system, making it difficult to repair heart problems. Therefore, maintenance of hydraulic cylinders should be cautious. Professional elevator manufacturers have advanced technology, strict testing, more affordable prices, and more discounts. Welcome to consultSelection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.Process inspection,The use of cleaning oil and the brand used in the systemThe manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.What are the methods for reducing shaking on lifting platforms? Reducing the shaking of the lifting platform can reduce the psychological obstacles of the operators, ensure the smooth progress of the operation, and also greatly help improve safety. Warm reminder: safety, do not operate blindly. Lifts are widely used in many places, and their working principles vary. Today, we will analyze the working principles of elevators. The types of elevators are generally divided into the following: fixed elevators, This type of elevator uses hydraulic oil cylinders and pump stations to transmit power, in the form of a scissor fork type. According to customer requirements, the length of the support rod for the scissor fork,corkCustomized hydraulic lifting platform, the number of layers the angle of the angle axis, and the expansion and contraction of the oil cylinder complete the lifting operation. Its advantages are large load-bearing capacity, and high safety.

After hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.consumption,The hydraulic elevator overflow valve can also generate high noise. When air is mixed in hydraulic oil, the overflow valve is stuck or severely worn the spring of the overflow valve is fatigued and deformed, and the relief time of the overflow valve is too short, it is easy to cause the pilot valve performance of the overflow valve to be partially stable, it should be replaced.On the other hand, under the action of high pressure,corkFixed electric hydraulic lifting platform, the hydraulic system inevitably causes the hydraulic valve to flow back or the sealing components to produce oil. The main reasons for the natural descent of the hydraulic cargo elevator include the following points: replacement of the support valve due to leakage. The lowering valve is damaged or not powered on. Require the lowering valve to be kept clean on a daily basis, and if damaged, replace it with a new hydraulic lowering valve in a timely manner.The lifting platform is a multifunctional heavy loading and unloading mechanical equipment, which can be divided into fixed and mobile, guide rail and curved arm types. Fixed types include scissor elevators, chain elevators, loading and unloading platforms, and attached electric construction platforms.cork,Ensure that there is a suitable power supply at the installation site, and separate maintenance of the distribution box is required. The distribution box should have a leakage switch, and the hydraulic cargo elevator construction site should be equipped with a fire extinguisher to prevent welding operations from causing fires. When selecting a leakage switch, it should be suitable for the operating power.For hydraulic cylinders in hydraulic elevators, it is not practical to change their effective working area A (equivalent to displacement) to adjust the speed. Generally, the speed can only be adjusted by changing the flow rate. For variable displacement motors, speed regulation can change both the flow rate and the motor displacement.Wholesale manufacturers of hydraulic cargo elevators have found that the market demand for hydraulic cargo elevators is also increasing. More importantly, some cargo loading and unloading work, as well as decoration, hotels, logistics, warehouses, supermarkets, etc., are commonly used in these situations, which are also specially processed and manufactured,corkLifting platform hydraulic pressure, and have some differences from the hydraulic cargo elevators we often see. There are significant differences in structure, shape, lifting speed, and height, and the prices of hydraulic cargo elevators also vary. The hydraulic cargo elevators used in the decoration industry have a low lifting height, some only meters and do not require many materials. He mainly promotes people, not goods, and rarely promotes goods, so the load is small, but not inferior to the use of other hydraulic cargo elevators. He is stable, interpretable, and durable enough to make hydraulic cargo elevators a good helper in the decoration industry. The function of hydraulic cargo elevators is gradually improving with our needs, and the properties we require are different. Wholesale manufacturers of hydraulic cargo elevators also manufacture according to our requirements.