there is no need to build complex ground protection and fixed devices

　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged　　 If there is no corresponding water leakage sensor, it is necessary to regularly maintain the submersible slurry pump and replace the seals.Bahrain,　　The specific treatment methods are as follows: first, check the power supply of the power supply to see whether the connector of the power supply is secure whether the switch is tight, and whether the fuse is intact. In case of short circuit, short circuit, fuse burnout and other problems, it shall be repaired in time. If it is not a power problem, check the water pump　　Reasonable.LexingtonFayette,　　Work no noise and vibration, and the site is cleaner.　　What stands out is the sealing of the container. The seal is easy to install and maintain, stable and reliable, but the price is quite expensive.　　In fact, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it too

　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　And multi-stage slurry pump; Fourth, the types of slurry pump can be divided from the pump shell of slurry pump: single shell slurry pump and lecture slurry pump; Let&#;s talk more about the model classification of slurry pumps: such as ah, HH, m slurry pumps. These series of slurry pumps can be collectively referred to as fractional series slurry pumps because these types　　In this way, a smooth surface can be formed on the surface.Total quality assurance, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, but in fact, we use it at ordinary times　　The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned.　　The submersible slurry pump is developed to adapt to the increasingly complex working conditions and facilitate the use of users. Its use mode is more flexible. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.

　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.knowledge,　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller　　 it can be used within the full head to ensure that the motor will not be overloaded.　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller!Bahrain, so it usually uses some small Flow and small pressure.　　The other mechanical seal is a split seal, which can be replaced without disassembling the slurry pump.　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades,BahrainWater well pipeline pump, but pay attention to adjusting the vacuum pump